Tonka Playskool User manual

*
OVER 9 months
to 3 years
91056
Scoot ’n Scoop 3-in-1 Ride-on™
with Revvin’ Beepin’ Wheel™
Thank you for choosing this TONKA toy!
Includes REVVIN’ BEEPIN’
WHEEL, truck body, seat,
gravel guard, rear axle
assembly, 2 screws,
3 plastic blocks and
instructions.
Adult supervision
required.
x3
BATTERIES INCLUDED
1.5V A A or R6 size
Replace with 3 x 1.5V “AA” or R6 size batteries.
Alkaline batteries recommended. Phillips/cross
head screwdriver (not included) needed to
replace batteries.
1Push
(9+ months)
2Walk
(12+ months)
3Ride
(18+ months)
This product contains small
parts which are necessary for
assembly. Prior to and during
assembly of this product, keep
small parts out of children’s
reach. Small parts pose a
choking hazard to children
under 3 years.
TO AVOID SERIOUS INJURY: continuous adult supervision required;
never use near motor vehicles, near streets, swimming pools, hills,
steps, or sloped driveways. Always wear shoes. Allow only one rider.
WARNING:
™
Adult assembly
and Phillips/
cross head
screwdriver
(not included)
required.
For children up to
42 pounds (19 kg).

ASSEMBLY
Basic
Attach rear axle
assembly to truck body
with the 2 screws.
Push Mode
1. Make sure seat
is locked in the
“down” position.
2. Make sure gravel
guard is locked
in the “down”
position.
Walk Mode
2. Attach seat in the
“up” position. Push
down until the
buttons click to
lock seat in place.
1. Remove seat by
pressing both
buttons at the
same time and
lifting the seat up.
Ride-on Mode
3. Remove gravel guard by pushing
both buttons at the same time
and lifting the gravel guard up.
1. Remove seat by
pressing both buttons
at the same time and
lifting the seat off the
truck body.
2. Attach seat in the
“down” position. Push
down until the buttons
click to lock seat
in place.
NOTE: Seat must be in “down” position for child to ride on
vehicle. Never allow child to sit or ride on gravel guard.
4. Attach the gravel guard
in the “up” position by
pushing both buttons
at the same time and
inserting guard vertically
into slot, then pushing
down on the gravel guard
until buttons click and
guard is locked in place.

PLAY
Revvin’ Beepin’ Wheel
2. Align tabs on base of
WHEEL with slots on top of
gravel guard.
3. Slide button on underside
of gravel guard away from
truck body and lower
WHEEL into gravel guard
housing. Release button
and pull up on WHEEL to
make sure it is locked in
place.
1. Make sure gravel guard is locked
in the “down” position. If it is in
the “up” position, press both
buttons at the same time and
pull gravel guard up and off the
truck body. Attach in the “down”
position by pressing buttons and
inserting guard horizontally into
slot, then pushing down on the
gravel guard until buttons click
and guard is locked into place.
To attach to SCOOT ’N SCOOP 3-IN-1 RIDE-ON:
To detach WHEEL from SCOOT ’N SCOOP 3-IN-1
RIDE-ON: Slide button on underside of gravel guard
away from truck body until you can lift the wheel up
(you will initially only be able to pull on the side of
the WHEEL closest to the front of the truck).
Revvin’ Beepin’ Wheel
To operate:
• Turn key to activate electronic
sounds.
• WHEEL can be used alone or
attached to SCOOT ’N SCOOP
3–IN–1 RIDE-ON.
Mirror is
adjustable!
WHEEL shakes to imitate road vibrations!
Horn makes
4 different
“honking”
sounds!
Directional
lights blink!
Gearshift
clicks!
Key
turns
Scoot ’n Scoop 3-in-1 Ride-on
Scooping action is powered by the forward motion of
the truck; place blocks in front of truck, then push truck
forward and over the blocks to scoop them up.
• Truck has 3 modes: push, walk and ride!
• Shape-blocks help sorting skills! Child can sort the
shape-blocks into the slots on the truck seat.
• Scooping
action picks up
shape-blocks!
• REVVIN’ BEEPIN’ WHEEL and
RUMBLIN’ ROLLIN’ CRANE
(sold separately) can be
attached to truck for more
sounds, lights and towing fun!
View of button on
underside of gravel guard.

© 2006 Hasbro.
All Rights Reserved.
TM & ® denote U.S.
Trademarks.
FCC STATEMENT
This equipment has been tested
and found to comply with the
limits for a Class B digital device,
pursuant to Part 15 of the FCC
Rules. These limits are designed
to provide reasonable protection
against harmful interference in
a residential installation. This
equipment generates, uses and
can radiate radio frequency
energy, and, if not installed
and used in accordance with
the instructions, may cause
harmful interference to radio
communications. However, there
is no guarantee that interference
will not occur in a particular
installation. If this equipment
does cause harmful interference
to radio or television reception,
which can be determined by
turning the equipment off and on,
the user is encouraged to try to
correct the interference by one or
more of the following measures:
• Reorient or relocate the
receiving antenna.
• Increase the separation
between the equipment and the
receiver.
• Consult the dealer or an
experienced radio/TV technician
for help.
Tonka.com
Questions? Call: 1-800-PLAYSKL
Locate battery compartment
cover on top of REVVIN’
BEEPIN’ WHEEL. Use a Phillips/
cross head screwdriver (not
included) to loosen screw in
battery compartment cover
(screw remains attached to
cover). Remove cover. Remove
exhausted batteries and
replace with 3 x 1.5V “AA” or R6
size batteries. Alkaline batteries
recommended. Replace cover
and tighten screw.
TO REPLACE BATTERIES
CAUTION: TO AVOID BATTERY LEAKAGE
1. Be sure to insert the batteries correctly and always follow
the toy and battery manufacturers’ instructions;
2. Do not mix old and new batteries or alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium) batteries;
3. Always remove weak or dead batteries from the product.
IMPORTANT: BATTERY INFORMATION
Please retain this information for future reference.
Batteries should be replaced by an adult.
CAUTION:
1. Always follow the instructions carefully. Use only batteries specified and
be sure to insert item correctly by matching the + and – polarity markings.
2. Do not mix old batteries and new batteries, or standard (carbon-zinc) with
alkaline batteries.
3. Remove exhausted or dead batteries from the product.
4. Remove batteries if product is not to be played with for a long time.
5. Do not short-circuit the supply terminals.
6. Should this product cause, or be affected by, local electrical interference,
move it away from other electrical equipment. Reset (switching off and
back on again or removing and re-inserting batteries) if necessary.
7. RECHARGEABLE BATTERIES: Do not mix these with any other types of
batteries. Always remove from the product before recharging. Recharge
batteries under adult supervision. DO NOT RECHARGE OTHER TYPES
OF BATTERIES.
Product and colors may vary.
91056 PN 6673920000