Toro Sand Pro 3040 User manual

1
All Rights Reserved
Printed in the USA
W2006 by The Toro Company
8111 Lyndale Avenue South
Bloomington, MN 55420-1196
Finish Grader Kit
Sand Pro)3040 & 5040
Model No. 08754–Serial No. 260000001 and Up
Form No. 3354–263 Rev. A
Installation Instructions
Safety and Instruction Decals
Safety decals and instructions are easily visible to the operator and are located near any
area of potential danger. Replace any decal that is damaged or lost.
106-5517
1. Warning—do not touch the hot surface.
Loose Parts
Note: Use the chart below to identify parts used for assembly.
Description Qty. Use
Finish Grader Assembly 1Mount to the Sand Pro lift arm adapter
Parts Catalog 1
Installation Instructions 1
Installation
Mount the Finish Grader to the Traction
Unit
1. Remove any attachment from the rear of the machine.
2. Back the traction unit into position in front of the
attachment adapter. Lower the traction unit adapter.
Note: Make sure the locking lever (Fig. 1) is pivoted to
the left (unlocked position) as viewed from the rear of the
machine.
3. Raise the traction unit adapter into the attachment
adapter.
4. Pivot the locking lever to the right to lock the adapters
together.
1
2
Rear of machine
Figure 1
1. Attachment adapter 2. Locking lever

2
Adjusting the Link Assembly
1. With the attachment mounted and secured on the
traction unit, raise the attachment.
2. Measure the gap between the top washer and the
spacer in the link assembly on the attachment adapter
as shown in figure 2.
The gap between the washer and the shoulder should be
0.060 to 0.080 inch
2
3
1
Figure 2
1. 0.060 to 0.080 inch
2. Jam nut
3. Adjustment nut
Operation
•Raise or lower the finish grader to control the grading
or scarifying depth.
•When grading, rotate the scarifier to the upper position
and secure each end with a clevis pin and hairpin
cotter (Fig. 3).
1
2
3
Figure 3
1. Scarifier
2. Grading position (upper)
3. Scarifying position (lower)
•When scarifying, rotate the scarifier to the lower
position and secure each end with a clevis pin and
hairpin cotter (Fig. 3).
•The scarifier aggressiveness can be changed by
adjusted the length of the springs (Fig. 5). Lengthening
the springs will make the scarifier less aggressive.
Shortening the springs will make the scarifier more
aggressive.
•For final grading/leveling, an Adjustable Orifice Kit,
Part No. 112–1433 can be obtained to regulate the
raise/lower speeds.
Inspection and Clean–up
When the grading operation is completed, clean the
machine thoroughly. Since this machine is used primarily
in sand, and sand is extremely abrasive, the sand should
be flushed off after each use. If the machine is cleaned
frequently, (before the sand has a chance to ”cake”), it can
be cleaned with a stream of water from a hose with the
nozzle removed. A high pressure stream could drive the
sand into wear areas where it could act as a grinding
compound.

3
Maintenance
Greasing the Attachment
If the locking lever on the attachment adapter does not
pivot freely and easily, apply a light coat of grease to the
area shown in figure 4.
Figure 4
Adjusting the Actuating Rod Springs
The springs and actuating rods are adjusted at the factory.
However, if new parts are installed or the springs are
removed for any reason, the spring length should be
adjusted to 5.24 inches (Fig. 5)
5.24”
Figure 5
Leveling the Finish Grader Blade
To level the blade in relation to the traction unit, place the
unit on a level surface (such as a concrete driveway), and
slightly vary the rear tire pressure as required.
Reversing the Scraper Blade
The scraper blade (Fig. 6) can be reversed for a second
wear surface after the original edge has worn beyond
acceptable limits.
1
Figure 6
1. Scraper blade
Optional Equipment
Weeder Tooth Scarifier Part No. 112–0260–03
Carbide Tipped Tooth Scarifier Part No. 110–0260–03
(15 required for each)

The Toro General Commercial Products Warranty
A Two-Year Limited Warranty
Conditions and Products Covered
The Toro Company and its affiliate, Toro Warranty Company,
pursuant to an agreement between them, jointly warrant your Toro
Commercial Product (“Product”) to be free from defects in
materials or workmanship for two years or 1500 operational
hours*, whichever occurs first. Where a warrantable condition
exists, we will repair the Product at no cost to you including
diagnosis, labor, parts, and transportation. This warranty begins
on the date the Product is delivered to the original retail purchaser.
* Product equipped with hour meter
Instructions for Obtaining Warranty Service
You are responsible for notifying the Commercial Products
Distributor or Authorized Commercial Products Dealer from whom
you purchased the Product as soon as you believe a warrantable
condition exists.
If you need help locating a Commercial Products Distributor or
Authorized Dealer, or if you have questions regarding your
warranty rights or responsibilities, you may contact us at:
Toro Commercial Products Service Department
Toro Warranty Company
8111 Lyndale Avenue South
Bloomington, MN 55420-1196
952-888-8801 or 800-982-2740
E-mail: [email protected]
Owner Responsibilities
As the Product owner, you are responsible for required mainte-
nance and adjustments stated in your operator’s manual. Failure
to perform required maintenance and adjustments can be grounds
for disallowing a warranty claim.
Items and Conditions Not Covered
Not all product failures or malfunctions that occur during the
warranty period are defects in materials or workmanship. This
express warranty does not cover the following:
•Product failures which result from the use of non-Toro
replacement parts, or from installation and use of add-on,
modified, or unapproved accessories
•Product failures which result from failure to perform required
maintenance and/or adjustments
•Product failures which result from operating the Product in an
abusive, negligent or reckless manner
•Parts subject to consumption through use unless found to be
defective. Examples of parts which are consumed, or used up,
during normal Product operation include, but are not limited to,
blades, reels, bedknives, tines, spark plugs, castor wheels,
tires, filters, belts, and certain sprayer components such as
diaphragms, nozzles, and check valves, etc.
•Failures caused by outside influence. Items considered to be
outside influence include, but are not limited to, weather,
storage practices, contamination, use of unapproved coolants,
lubricants, additives, or chemicals, etc.
•Normal “wear and tear” items. Normal “wear and tear” includes,
but is not limited to, damage to seats due to wear or abrasion,
worn painted surfaces, scratched decals or windows, etc.
Parts
Parts scheduled for replacement as required maintenance are
warranted for the period of time up to the scheduled replacement
time for that part.
Parts replaced under this warranty become the property of Toro.
Toro will make the final decision whether to repair any existing part
or assembly or replace it. Toro may use factory remanufactured
parts rather than new parts for some warranty repairs.
General Conditions
Repair by an Authorized Toro Distributor or Dealer is your sole
remedy under this warranty.
Neither The Toro Company nor Toro Warranty Company is
liable for indirect, incidental or consequential damages in
connection with the use of the Toro Products covered by this
warranty, including any cost or expense of providing substi-
tute equipment or service during reasonable periods of
malfunction or non-use pending completion of repairs under
this warranty. Except for the Emissions warranty referenced
below, if applicable, there is no other express warranty. All
implied warranties of merchantability and fitness for use are
limited to the duration of this express warranty.
Some states do not allow exclusions of incidental or consequential
damages, or limitations on how long an implied warranty lasts, so
the above exclusions and limitations may not apply to you.
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
Note regarding engine warranty: The Emissions Control System
on your Product may be covered by a separate warranty meeting
requirements established by the U.S. Environmental Protection
Agency (EPA) and/or the California Air Resources Board (CARB).
The hour limitations set forth above do not apply to the Emissions
Control System Warranty. Refer to the Engine Emission Control
Warranty Statement printed in your operator’s manual or con-
tained in the engine manufacturer’s documentation for details.
Countries Other than the United States or Canada
Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer)
to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor’s service or
have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty
Company.
Part No. 374-0031 Rev. C