Toshiba SD-M1302 User manual

SD-M1302 & SD-M1402 DVD-ROMs
with REALmagic Hollywood+ Playback Card
Installation Instructions
Congratulations on your purchase of a Toshiba SD-M1302 or SD-M1402
DVD-ROM drive and REALmagic Hollywood+ DVD/MPEG-2 Playback
Card Kit. The following information will help you in the simple installa-
tion of your new DVD-ROM. It is assumed that you are replacing a
presently installed CD-ROM with the enclosed DVD-ROM. If this is not
the case, additional installation hardware may be required. Refer to
REALmagic Hollywood+ User’s Guide for installation instructions on
the DVD/MPEG-2 Playback Card.
CHECKINGYOUR KIT PACKAGING
Please unpack your DVD kit, and assure that youhave the following items:
lToshiba SD-M1302 or SD-M1402ATAPI DVD-ROM drive
lDVD/MPEG-2 PCI Playback Card (compatible with all graphics cards)
l13” 3.5mm ext. audio cable
l14” HDB15 - 9 DIN overlay cable
lS-Video to RCA video converter cable
lREALmagic™Accessory Kit envelope
(with software, demo CD and Playback Card User’s Guide)
lSD-M1302 & SD-M1402 DVD-ROM Installation Instructions
(this manual)
Additional items you may need that are not included in the kit are:
lScrewdriver
lmounting screws and mounting hardware
lIDE BUS cable
lDVD/CD-ROM Sound Cable
SYSTEM REQUIREMENT
The DVD-ROM kit requires the following:
✔2MB of free hard disk space
✔16MB of RAM
✔Pentium-based PC (or compatible), 133MHz or higher
✔PCI 2.1 compliant expansion slot
✔VGACard
✔Plug and Play BIOS support
✔Microsoft™ Windows 95 or higher
✔Amplified stereo speakers
TOSHIBA

The following steps must be performed to properly install your DVD-
ROM.
lSet DVD-ROM Drive Jumper Settings
lConnect Audio Cable
lAttach IDE BUS cable
lMount DVD-ROM
SETTING JUMPERS
C
SS
LM A
The mode select jumpers are 6 straight angle pins located on the rear of
the DVD-ROM. By placing a jumper on the pins, you can select the
following functions:
CS: – Drive is configured using host interface signal CSEL
SL: – Configures drive as Slave
MA: – Configures drive as Master (default mode)
In most installations, jumper should remain in MA position (factory de-
fault). It is recommended that you install your DVD-ROM only on the
secondary IDE BUS. If you are installing on primary IDE BUS, your
hard drive would then be the Master, and you should set your DVD-
ROM to the Slave position (SL).
2

PLACING DVD-ROM INSIDE YOUR COMPUTER
Now that you have set the jumpers, you are ready to install your DVD-
ROM inside your computer.
IMPORTANT: Disconnect power from your computer system before
beginning installation.
Remove computer cover and faceplate if required. Refer to your com-
puter system’s manual for removal information. If DVD-ROM is replac-
ing a CD-ROM, remove CD-ROM presently installed in your system.
Your Toshiba DVD-ROM can be placed in any free half-height drive slot
at the front of your computer. (It can be mounted horizontally or verti-
cally.)
Carefully start sliding the DVD-ROM into the opening with the disc tray
facing the front of the computer. Before you push the drive all the way in
you will need to connect the IDE BUS cable,Audio cable and the Power
cable on the back of the drive.
Connecting Cables
IDE BUS Cable (not supplied with kit) - Your computer system should
have a primary and secondary IDE BUS, cable with your Hard Drive
most likely being the Master on the primary BUS. Connect BUS cable as
follows, assuring that pin 1 of cable (side with red stripe) is connected to
pin 1 of DVD-ROM interface connector:
If you are replacing your CD-ROM: connectDVD-ROM to theBUS Cable
connector that the CD-ROM was connected to.
If DVD-ROM is not replacing a CD-ROM or is an addition to a CD-
ROM: connect DVD-ROM to an open connector on the secondary IDE
BUS cable (not supplied with kit).
If DVD-ROM is to be slave on Primary BUS: connect DVD-ROM to open
connector on the primary IDE BUS cable (not supplied with kit).
3

Power Cable - Connect an internal computer power supply cable to the
power socket at the back of the DVD-ROM. One side of the plug has
chamfered edges, so the power connector fits only one way. Push plug
completely into the socket making sure the plug fits correctly.
Audio Cable (optional) - If you have a sound card and speakers, and
would like to play audio CDs on your computer, you will need to get a
sound cable. Contact our small parts supplier, AMC at 888/262-9700
(http://amc-marketplace.com). Sound cables are made for the sound
card you are using and the DVD-ROM to which you are connecting.
Make sure you have this information when purchasing a sound cable.
The sound cable connects to your sound card at one end and the other
end connects to the analog audio connector at the left rear of the DVD-
ROM (see DVD-ROM Back Panel photo on page 5 for location). Refer
to the instructions which came with your sound card for details on any
sound-driver software required. Also refer to the REALmagic Holly-
wood+ User’s guide for additional audio connection options.
4

COMPLETING INSTALLATION
After you have connected all the necessary cables, push the DVD-ROM
completely intothe computer’s driveslot. Mountdrive peryourcomputer’s
instructions. The screw length should
not exceed 3±0.5mm (measured from
outside surface of side or bottom of
DVD-ROM to tip of screw). Replace
computer cover and all outer screws.
Software Driver: Toshiba’s DVD-
ROM Drive is “plug n’play”. In Win-
dows, when you apply power to your
computer and boot-up, the system will
recognize new hardware, and begin installing Window’sATAPI driver. If
you prefer using DOS, you can download an ATAPI driver from our web
site (http://www.toshiba.com/taecdpd/support/drivers.shtml). After you
have completed installing your DVD-ROM, refer to REALmagic™ User’s
Guide to install DVD/MPEG-2 Playback Card.
DVD-ROM FRONT PANEL
The photo illustrates the following features of the SD-M1302 and SD-
M1402 DVD-ROMs front panel:
➀➀
➀➀
➀ DVD loading tray
➂➂
➂➂
➂ Emergency eject hole (insert solid bar
➁➁
➁➁
➁ Eject button into hole, i.e. paper clip, and push until
➃➃
➃➃
➃ Busy light tray opens)
DVD-ROM BACK PANEL
The photo below illustrates the following features of the SD-M1302 and
SD-M1402 DVD-ROMs back panel:
;
;
;
;
;
3 ±0.5mm
Surface of side or bottom
of drive
Mounting frame of
host computer
Mounting Screw
M3
5
➀ ➀
➀ ➀
➀ Digital audio out connector
➃ ➃
➃ ➃
➃ ATAPI connector
➁ ➁
➁ ➁
➁ Analog audio out connector
➄ ➄
➄ ➄
➄ Power connector
➂ ➂
➂ ➂
➂ Mode select jumper

Specifications SD-M1302 SD-M1402
DVD CD DVD CD
DATA CAPACITY Mode Mode Mode Mode
(bytes/block) 2,048 1 2 2,048 1 2
2,048 2,336 2,048 2,336
ROTATIONAL DVD: CD: 8,500 DVD: CD/CDR: 8,500
SPEED (rpm) 4,600 (17.2-40X) single layer: (17.2-40X)
(3.3-8X) CD-RW: 4,300 6,900 (5-12X) CD-RW: 4,300
DVD-R: (8.6-20X) dual layer: (8.6-20X)
1,100- Audio/Video: 6,300(4.1-10X) Audio/Video:
2,800 1,200 - 2,000 DVD-R: 1,200 - 2,000
(2X) (4-5.7X) 2,800 (2X) (4-5.7X)
SUSTAINED Mode Mode Mode Mode
DATA TRANSFER 4,460 - 1 2 6,750 - 1 2
RATE (kbytes/sec) 10,800 2,595- 2,959- 16,200 2,595- 2,959-
6,000 6,843 6,000 6,843
ACCESS TIME (typ)
Avg. RandomAccess 95ms 80ms 95ms 80ms
Avg. Random Seek 85ms 75ms 80ms 75ms
Avg. Full Stroke 210ms 145ms 170ms 140ms
DATA BUFFER 256kbytes 128kbytes
POWER SUPPLY +5v, +12V
MTBF 100,000 hours
DIMENSIONS 5.75” X 1.6” X 7.6” (146mmx41.5mmx193mm)
WEIGHT 1.92lbs/0.87kg 2.09lbs/0.95kg
460014-D0
P/N 460014-D0
TECHNICAL SUPPORT
Technical support can be obtained by calling 949/455-0407 or e-mail-
ing: [email protected]. Additional technical information can be
found on our website at: http://www.toshiba.com/taecdpd/
FCCDECLARATIONOFCONFORMITY
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaclassB digitaldevice,pursuant topart
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by
turningtheequipmentoff and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a class B computing device, pursuant to FCC
Rules. In order to maintain compliance with FCC regulations, shielded cables must be used with this
equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to
radio and TV reception. The user is cautioned that changes and modifications made to the equipment without
the approval of the manufacturer could void the user's authority to operate this equipment.
LASERCAUTION
This appliance contains a laser system and is classified as a "CLASS 1 LASER PRODUCT". To use this model
properly,readthisOwner'sManualcarefullyandkeepthismanualforfuturereference. Incaseofanytroublewith
thismodel, pleasecontact yournearest "AuthorizedRepairCenter".Toprevent directexposure tothelaserbeam,
do not try to open the enclosure