Toshiba TheaterWide 44HM85 User manual

- 1 -
SERVICE MANUAL
Projection Television
44HM85
FILE NO. 050-200534
Published in Japan, Sep. 2005 (YC)
TOSHIBA CORPORATION 2005

- 2 -
TABLE OF CONTENTS
SAFETY PRECAUTIONS ...........................................................................................................................................................3
SPECIFICATIONS.......................................................................................................................................................................4
DESCRIPTION OF CONTROLS.................................................................................................................................................5
ADJUSTMENT INSTRUCTION ................................................................................................................................................12
EXPLODED VIEW ....................................................................................................................................................................16
REPLACEMENT PARTS LIST ..................................................................................................................................................17
PC BOARDS TOP & BOTTOM VIEW .......................................................................................................................................32
BLOCK DIAGRAM ....................................................................................................................................................................39
SCHEMATIC DIAGRAM ............................................................................................................................................................43

- 3 -
SAFETY PRECAUTIONS
General Guidance
An lsolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the
AC power line. Use a transformer of adequate power rating as
this protects the technician from accidents resulting in personal
injury from electrical shocks.
It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitary that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this monitor is blown, replace
it with the specified.
When replacing a high wattage resistor (Oxide Metal Film
Resistor, over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source, connect
an electrical jumper across the two AC plug prongs.
Place the AC switch in the on positioin, connect one lead of
ohm-meter to the AC plug prongs tied together and touch other
ohm-meter lead in turn to each exposed metallic parts such
as antenna terminals, phone jacks, etc.
If the exposed metallic part has a return path to the chassis,
the measured resistance should be between 1MΩand 5.2MΩ.
When the exposed metal has no return path to the chassis
the reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified
by in the Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this
manual to prevent Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this
check.
Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC
voltmeter with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC
voltage measurements for each esposed metallic part. Any
voltage measured must not exceed 0.75 volt RMS which is
corresponds to 0.5mA.
In case any measurement is out of the limits sepcified, there
is possibility of shock hazard and the set must be checked
and repaired before it is returned to the customer.
Leakage Current Hot Check circuit
TOSHIBA OF CANADA LTD.
191 McNABB STREET, MARKHAM.
ONTARIO, L3R 8H2, CANADA
TEL : [phone]
1.5 Kohm/10W
To Instrument's
exposed
METALLIC PARTS
Good Earth Ground
such as WATER PIPE,
CONDUIT etc.
AC Volt-meter
0.15uF

- 4 -
Product Specifications
Model
44HM85 Horizontal Size (Inches) 39.9
Height (Inches) 29.2
Depth (Inches) 14.3
Weight (lbs.) 56.2
Power Requirement AC 120V, 60Hz
Television System American TV Standard, NTSC, ATSC with STB
Television Channels VHF: 2 - 13
UHF: 14 - 69
CATV: 1 - 125
Power Consumption (W) 210W
Antenna 75 ohm External Terminal for VHF/UHF
Audio Output (W) 15W x 2
External Input/Output Ports A/V input (3 set)
Monitor out (1 set)
S-Video input (3)
COLORSTREAM HD input (2 set)
RGB input (1)
HDMI input (1)
RGB audio input (1 set)
UPGRADE port (1)
RF input (1)
• This model complies with the specifications listed below.
• Designs and specifications are subject to change without notice.
• This model may not be compatible with features and/or specifications that may be
added in the future.
SPECIFICATIONS

- 5 -
Function Status Indicators
Lamp indicator, operation indicator, and temperature indicator located below the front panel controls,
reveal the operating status of the DLP projection TV.
Operation Indicator
Lamp Indicator
Temperature Indicator
Off Power cord is not connected.
Red Power Cord is connected, unit is on standby mode.
Green TV turns on.
Orange (flashing) Preparing operation in standby mode.
Red (flashing) There is a problem with the lamp or around it. Contact
an authorized service center.
Green (flashing) The lamp cover is not closed.
Red The projection TV has shut down due to overheating.
After viewing the phrase “Thermal High Error”.
Red (flashing) The projection TV shut down due to the cooling fan
trouble. Contact an authorized service center.
Orange Thermal warning.
Operation Indicator
Lamp Indicator
Temperature Indicator
DESCRIPTION OF CONTROLS

- 6 -
S-VIDEO
VIDEO
AUDIO
(R)
(L)/
MONO
AV3
INPUT
HDMIINPUT
U
P
G
R
A
D
E
P
O
R
T
PC/DTV
(SXGA/
480p/
576p/
720p/
1080i)
(L)
AUDIO
(R)
RGBINPUT
DVI/ RGBINPUT
MONITOR
OUT
A/V2
INPUT
A/V1
INPUT
VIDEO
(L)
AUDIO
(R)
S-VIDEO
MONO
COMPONENT
P R
P B
Y
(L)
AUDIO
(R)
480i/480p/
576i/576p/
720p/1080i
480i/480p/
576i/576p/
720p/1080i
INPUT2
INPUT1
HDMI INPUT
U
P
G
R
A
D
E
P
O
R
T
PC/DTV
(XGA/
480p/
720p/
1080i)
(L)
AUDIO
(R)
RGB INPUT
MONITOR
OUT
VIDEO 2
INPUT
VIDEO 1
INPUT
VIDEO
(L)
AUDIO
(R)
S-VIDEO
MONO
COLORSTREAM HD
P R
P B
Y
(L)
AUDIO
(R)
480i/480p/
720p/1080i 480i/480p/ 720p/1080i
INPUT 1
INPUT 2
Rear Connections Panel
Mini glossary
JACK A connection on the back of a TV, VCR, or any other A/V device. This includes the RF jack and the Audio/Video jacks that are
color-coded.
SIGNAL Picture and sound traveling through cable, or over the air, to your television screen.
S-VIDEO In
A connection available
with some high-end
equipment that provides
even better picture quality
for Video 2.
Video 1 or 2
Connects the video sig-
nals from various types
of equipment.
Connecting cables and external equipment to your TV.
Left/Right Audio
Used for stereo sound
from various types of
equipment.
UPGRADE PORT
This port is used to upgrade
the software version and
debug without changing the
hardware.
Be careful not to use this
port. Just contact your deal-
er or service centre.
RGB Input
Connect the TV output
connector from a PC/DTV
to the appropriate input
port.
RF Connector: Antenna
Used to connect analog
cable or antenna signals
to the television, either
directly or through your
cable box.
COLORSTREAM HD 1-2
Connect a ColorStream HD
video/audio device to these jacks.
Refer to your DVD manual for further
information.
HDMI
connect a HDMI signal
to HDMI.

- 7 -
Front Connection Panel
There are four jacks on the left side on your projection TV
that make connecting Audio/Video devices like video games
and camcorders very simple.
The jacks are like those found on the back jack connection
panel. This means that most equipment that connects to
those types of jacks on the rear jackpack, may be connect-
ed to the front connection panel.
To use the front jacks as the signal source, select them
using Main Input menu as described on page 44. They will
be named "Front Video" in the Main Input menu.
If you input both Front Video and
S-Video, only the S-Video will
work.
If you're connecting a video game
device, make sure to change the
picture settings with the Picture
Mode option in the PICTURE
menu.
Mini glossary
A/V CABLESAudio/Video cables. Three cable connectorÑRight audio (red), Left audio (white), and V ideo (yellow). A/V cables are used
for stereo playback of videocassettes and for higher quality picture and sound from other A/V devices.
A/V DEVICE Any device that produces video or sound (VCR, DVD, cable box, or television).
Front A/V Panel
S-VIDEO
VIDEO
FRONTA/V
AUDIO
(R)
(L)/
MONO
Left/Right Audio
Used for stereo
sound from various
types of equipment.
Video
Connects the video
signals from any
piece of equipment.
S-Video
A connection available on
some very high-end equip-
ment that provides better
picture quality than video
input.

- 8 -
Remote Control Functions in TV Mode
1 2 3
4 5 6
7 8 9
0
TV
MODE LIGHT POWER
TV/VIDEO HDMI
RGB
VCR CABLE DVD SAT
MUTE
SWAPPIPCH- PIPCH+
PIP
PIC SIZE
REC STOP
PAUSE
REW
PLAY
FF
MENU EXIT
CC FREEZE
PIP INPUT
VOL CH
SURF
SAP VIDEO
C/S HD2C/S HD1
FRONT
SKIP
ENTER
CH RTN
SURF
Scrolls the Surf channel list.
MENU
Brings up the main
menu to the screen.
EXIT
Clears all on-screen dis-
plays and returns to TV
viewing from any menu.
FREEZE
Freezes the currently-viewed pic-
ture. Sub picture is frozen in
PIP/DW picture mode.
VIDEO
Adjusts the factory preset
picture according to the
room.
PIPCH+
Changes to next higher PIP
channel.
SWAP
Switches the picture from
PIP, POP, or twin picture to
the main screen.
MUTE
Switches the sound on or off
THUMBSTICK
Allows you to navigate the on-screen
menus and to adjust the system set-
tings and preferences, by moving to
an option with
  and selecting the
highlighted option with .
TV/VIDEO
Selects: Analog, Video1,
Video2, Front Video,
Colorstream HD 1-2 and RGB
and HDMI input sources .
MODE
Selects the remote operating
mode: TV, VCR, Cable, DVD
and Satellite. Select other oper-
ating modes, for the remote to
control external devices.
FRONT
Selects the front video signal if
a device, such as a camcorder
or game player, is connected
to the front video input jack.
HDMI
Selects: HDMI-DTV and
HDMI-PC input sources.
SAP
Selects: Mono, Stereo, and
SAP.
PIPCH-
Changes to next
lower PIP channel
PIP
Toggles between PIP, POP
(Picture-outside-Picture)
and Twin picture mode.
LIGHT
Illuminates the remote con-
trol keys.
INDICATOR LIGHTS
Show active remote mode
every time any button is
pressed.



- 9 -
Remote Control Functions in TV Mode
1 2 3
4 5 6
7 8 9
0
TV
MODE LIGHT POWER
TV/VIDEO HDMI
RGB
VCR CABLE DVD SAT
MUTE
SWAPPIPCH- PIPCH+
PIP
PIC SIZE
REC STOP
PAUSE
REW
PLAY
FF
MENU EXIT
CC FREEZE
PIP INPUT
VOL CH
SURF
SAP VIDEO
C/S HD2C/S HD1
FRONT
SKIP
ENTER
CH RTN
POWER
Turns your TV or any other
programmed equipment on
or off, depending on mode.
CHANNEL UP/DOWN
Scrolls through available channels in
EZ Scan memory.
NUMBER KEYPAD
For direct channel selection and
programming functions.
ENTER
When in the menu system
and other on-screen dis-
plays, selects highlighted
options.
RECORD, PAUSE, REW,
FFWD, PLAY, STOP
Control the functions on your VCR.
VOLUME UP/DOWN
Increases/decreases the sound
level.
PIC SIZE
Changes the screen format or
aspect ratio.
SKIP
Playing CDs: Selects
songs.
Playing DVDs: Selects
movie chapters.
C/S HD1,HD2
Selects ColorStream HD signal
sources, such as DVD or HD
receiver.
ENTER
When in the menu system and
other on-screen displays,
selects highlighted options.
CH RTN
Tunes to the last channel
viewed.
CC
Selects a closed caption mode
for displaying captioning infor-
mation if available on program.
PIP INPUT
Selects the input source for the
sub picture.
RGB
Selects: RGB-DTV and
RGB-PC input sources.

- 10 -
On-Screen Displays
This page describes your on-screen display and information banner options.
10
Mute
Main Channel Display
Displays current channel number.
PIP Display
This display
appears when
PIP is active.
Volume
Volume level is displayed while
adjusting the sound.
Mute
Appears
when sound
is muted.
TV 13
CATV 16
11:17 AM

- 11 -
Front Panel Controls
1
24
36
7
8
5
POWER
MENU
ENTER (Same as ENTER button on your
remote control)
VOLUME UP / DOWN
CHANNEL UP / DOWN
Operation indicator.
Lamp indicator.
Temperature indicator.
1
2
3
4
5
6
7
8
See menu pages for instructions on using the
on-screen menus.
The POWER, MENU, ENTER, VOLUME, and
CHANNEL buttons work just as they do on
your remote control.
If TV is moved from cold to normal room tem-
perature, condensation may form inside the TV,
wait 6~7 hours for the TV to adjust to room
temperature before turning it on.
-
-
-

- 12 -
1. Application Object
These instructions apply to the DLP Projection TV (Chassis:
MB-05DC).
2. Notes
(1) Because this is not a hot chassis,it is not necessary to use
an isolation transformer. However, the use of an insolation
transformer will help protect test equipment.
(2) The adjustments must be performed in the correct
sequence.
(3) The adjustments must be performed in the condition of
25±5 C of temperature and 65±10% of relative humidity if
there is no other specific designation.
(4) The input voltage of the receiver must remain AC 120V,
60Hz.
(5) Unless stated otherwise, the set must be operated for at
least 5 minutes prior to adjustments.
The heat-run should be performed with a 100% white
pattern,but reception of a moving picture may also be
possible in unavoidable cases.
3. Composition of Adjustment Mode
(3) As shown <Fig. 1>, using the CH+ ( ), CH- ( ) keys to
select an item, press the ENTER Key to enter the
appropriate item and begin adjustment.
(4) Change the value of adjustment by using the ENTER Key.
To change adjustment item, use the CH+ ( ), CH- ( )
keys in ADJ Mode.
(5) Press the EXIT key to exit, after adjustments.
(6) Preparation for Adjustment
1) Connect the power to TV Set and set "Power on".
2) Allow set to Heat-Run for at least 5 minitues before
adjusting.
<Fig. 1> Adjustment Mode OSD
(1) Press MENU keys on the set and Remote Controller at
the same time for more than 10 sec.
(2) Initial Adjustment mode Menu is shown below. <Fig. 1>
4. Check the CWI/ NDC Adjustment
Movement and Default Data
(Base value --> CWI: 160, NDC: 12)
4-1. Required Test Equipment
Remote Controller.
4-2. Adjustment Preparation and Setting of
Device
(1) Connect power and turn Power on.
(2)
Using the Remote Controller, enter CWI/ NDC item in
Adjustment menu.
(3) Confirm variable operation and base value.
(CWI:160, NDC:12)
5. Check the Actuator Adjustment
Movement and Default Data
5-1. Required Test Equipment
Remote Controller.
5-2. Adjustment Preparation and Setting of
Device
(1) Connect power and turn Power on.
(2)
Using the Remote Controller, enter Actuator 60Hz item in
Adjustment menu.
(3) Confirm variable operation and base value of
ACT Gain
and Phase.
- Phase(Base value : 220)
- Gain(Base value : 70)
ADJUSTMENT INSTRUCTION
MB- 05DC
Area Code 1
OPTION1 0
OPTION2 0
OPTION3 0
OPTION4 12
OPTION5 205
Pattern
Position
Auto RGB(HEX)
CWI/ NDC
Actuator 6 0Hz
System control
Manual CCA
Lamp Type : PHIL
DDP1011 Ver : 2.15
SubMiComVer: 4.0
MainMiCom Ver : 3.06

- 13 -
6. Screen Position Adjustment
Area code adjustment: default(H: 0, V: 0)
6-1. Required Test Equipment
Remote Controller
6-2. Horizontal Position Adjustment
(1) Enter the adjustment mode.
(2) Select POSITION in the adjustment menu.
(3) The adjustment pattern below appears.
(4) Change data by using the VOLUME keys on the remote
control in order to adjust left/right screen symmetry.
(5) In case of over variable range is N.G.
<Fig . 2> Pattern for Screen Position Adjustment
6-3. Vertical Position Adjustment
(1) Change data with using CHANNEL key on the remote
Controller in order to adjust Upper/Lower screen symmetry.
(2) In case of over variable range is N.G.
After adjustment is completed, recieve a NTSC-M Digital
Pattern and check the adjusment level.
Adjustment
Adjustment
<Fig . 3> Digital Pattern
6-4. Area code Adjustment
(1) Enter the adjustment mode.
(2) Select Number 1 to the Area code of the adjustment menu.
7. Auto Color Balance Adjustment
7-1. Required Test Equipment
Remote Controller, MSPG-925FS Pattern Generator
(NTSC, 720p YPbPr output & PC 1024x768 @60Hz with
Standard(0.7Vpp)Vertical 100% Color Bar Pattern &
Vertical16 Gray Pattern)
<Fig. 4> COLOR BAR Pattern>
7-2. Preparation for Adjustment
(1) Connect power and turn TV set on.
(2) Perform Heat-Run for at least 5 minutes.
(3) Receive the Component1.
(4) Receive Color bar pattern of MSPG-925FS. <Fig. 4>
7-3. Adjusting the Auto Color Balance
Set TV into component input mode.
(1) Enter the adjustment mode after more than 10 seconds fo
receiving the signals(Color Bar Pattern).
(2) In adjustment items, enter the Auto RGB(HEX) and press
the
() button to enter the adjustment items.
Enter the Auto Color Balance
() t
o Set in the top of menu.
Press the button ( ) to complete and then the "OK" OSD
message will be displayed.

- 14 -
Set TV into PC input (RGB) mode.
be compensated manually.
(1).Enter to the adjustment mode after receive the signals <Fig. 5>
Vertical 16 Gray pattern.
(2).In adjustment items, enter the Auto RGB(HEX) and press
the
() button to enter the adjustment items.
Sub-screen(HUDSON) hand-operated compensation
After adjustment of PC-XGA/60Hz completed, if color
sensation of Vertical16 Gray Pattern seems out of order, it can
(1) Green is too strong , (greenish tone)
1) Menu -> Device -> Hudson
2) ADC G-Offset2 value of menu down.
3) After adjustment completed, press Exit button.
(2) Green is too weak. (violet tone)
1) Menu -> Device -> Hudson
2) ADC G-Offset2 value of menu up.
3) After adjustment completed, press Exit button.
8. Actuator Adjustment
8-1. Required Test Equipment
Remote Controller
8-2. Preparation for Adjustment
(1) Connect a power source to the TV Set and turn TV set on.
(2) Enter to Actuator 60Hz.
(3) ACT Gain and Phase is variable and the Tartan plaid of
the R, G, B, W Horizontal Line.
- The Phase(Base value: 220) variable adjust Mutation
point of Actuator.
- The Gain(Base value: 70) adjust mutation quantity of
Actuator.
Adjust ACT Gain and phase so that the Tartan plaid of R, G
When the R, G and B will not be ballanced, adjust the R
and B will not be visible.
and G to be ballanced.
Actuator 60Hz
ACT Phase 220
ACT Gain 70
<Fig. 7> Test Pattern
Before Actuator Adjustment After Actuator Adjustment
Enter the Auto Color Balance () t
o Set in the top of menu.
Press the button ( ) to complete and then the "OK" OSD
message will be displayed.
Set TV into HD1 color stream mode.
(1).Enter the adjustment mode after receiving the color bar.
Color bar pattern(MSPG-925FA 720P/60Hz)
(2).In adjustment items, enter the Auto RGB(HEX) and press
the
() button to enter the adjustment items.
Enter the Auto Color Balance
() t o Set in the top of menu
and press the ( ) button. If it is completed, the "OK" OSD
message is displayed.
<Fig. 5> Vertical 16 Gray Pattern
<Fig. 6> COLOR BAR Pattern

- 15 -
9. CWI/NDC Adjustment
(Base value --> CWI: 160, NDC: 12)
9-1. Required Test Equipment
Remote Controller
9-2. Preparation for Adjustment
(1) Connect power and turn the TV set on.
(2) Enter to CWI/NDC.
9-3. Adjustment
(1) Using the channel key, adjust CWI-Pat.1 to the left/right.
(2) During adjustment, check the appearance of noise in the
TEST Pattern.
Set the value to reduce green noise in step 3~4.
(3) Using CH UP/DOWN key of the Remote Controller, enter the
RED PATTERN.
(4) Check the uniformity of RED Pattern to verify.
Starting point of noise
(Appearance GREEN)
<Fig. 8> TEST Pattern(Lamp Gray Pattern)
<Fig. 9> TEST Pattern(RED Pattern)
9-4. NDC Adjustment
NDC Mode is for compensating the deviation of each Lamp.
Adjust Left/Right value with using CH UP/DOWN key on the
Remote Controller to set an uniformity for White color.
The sensitivity of sensor may vary due to the temperature.
Thus it may cause color changed bacause of the color wheel
angle changed.
<Fig. 10> TEST Pattern

- 16 -
304
303
305
121
300
301
310
650
600
120
630
700
410
400
433
430
401
402
681
680
670
432
431
503
174
623
612
611
610
617
618
616
720
615
502
601
530
590
602
640
620
570
571
622
520
501
540
EXPLODED VIEW
*The availability of some parts shown is subject to the condition applied.

- 17 -
CHASSIS AND CABINET REPLACEMENT PARTS LIST
Model : 44HM85
Capacitors ............. CD : Ceramic Disk PF : Plastic Film EL : Electrolytic
Resistors ............... CF : Carbon Film CC : Carbon Composition MF : Metal Film
OMF : Oxide Metal Film VR : Variable Resistor FR : Fusible Resistor
(All CD and PF capacitors are ±5%, 50V and all resistors, ±5%, 1/6W unless otherwise noted.)
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “SERVICE SAFETY PRECAUTIONS” ON PAGE 3 OF
THIS MANUAL.
CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components
which have special characteristics important for safety and should be replaced only with types identical to those in
the original circuit or specified in the parts list. The mounting position of replacements is to be identical with originals.
Before replacing any of these components, read carefully the SERVICE SAFETY PRECAUTIONS. Do not degrade
the safety of the receiver through improper servicing.
NOTICE:
• The part number must be used when ordering parts, in order to assist in processing, be sure to include the
Model number and Description.
• The PC board assembly with ∗ mark is no longer available after the end of the production.
Location Parts No. Reference Description
No.
CAPACITORS
C2 72782108 0CN1030F679 TUBULAR(HI, 10000PF D 16V 20% X5
C3 72782107 0CN1010K519 TUBULAR(HI, 100PF D 50V 10% B(Y5
C4 72782107 0CN1010K519 TUBULAR(HI, 100PF D 50V 10% B(Y5
C38 72782123 0CK225DFK4A CERAMIC, 2.2UF 2012 16V 20%, -
C39 72782123 0CK225DFK4A CERAMIC, 2.2UF 2012 16V 20%, -
C40 72782143 0CE227SF6DC ELECTROLYTIC, 220UF MVG 16V 20% R/
C41 72782149 0CE475SK6DC ELECTROLYTIC, 4.7UF MVG 50V 20% SM
C42 72782149 0CE475SK6DC ELECTROLYTIC, 4.7UF MVG 50V 20% SM
C49 72782123 0CK225DFK4A CERAMIC, 2.2UF 2012 16V 20%, -
C50 72782123 0CK225DFK4A CERAMIC, 2.2UF 2012 16V 20%, -
C52 72782123 0CK225DFK4A CERAMIC, 2.2UF 2012 16V 20%, -
C53 72782123 0CK225DFK4A CERAMIC, 2.2UF 2012 16V 20%, -
C55 72782123 0CK225DFK4A CERAMIC, 2.2UF 2012 16V 20%, -
C57 72782123 0CK225DFK4A CERAMIC, 2.2UF 2012 16V 20%, -
C58 72782143 0CE227SF6DC ELECTROLYTIC, 220UF MVG 16V 20% R/
C61 72782123 0CK225DFK4A CERAMIC, 2.2UF 2012 16V 20%, -
C65 72782138 0CE226SF6DC ELECTROLYTIC, 22UF MVG 16V 20% SMD
C66 72782138 0CE226SF6DC ELECTROLYTIC, 22UF MVG 16V 20% SMD
C72 72782135 0CE107SF6DC ELECTROLYTIC, 100UF MVG 16V 20% SM
C88 72782135 0CE107SF6DC ELECTROLYTIC, 100UF MVG 16V 20% SM
C91 72782123 0CK225DFK4A CERAMIC, 2.2UF 2012 16V 20%, -
C96 72782123 0CK225DFK4A CERAMIC, 2.2UF 2012 16V 20%, -
C97 72782123 0CK225DFK4A CERAMIC, 2.2UF 2012 16V 20%, -
C150 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C151 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C152 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C153 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C154 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C155 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C156 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C157 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C158 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C159 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C160 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C161 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C172 72782138 0CE226SF6DC ELECTROLYTIC, 22UF MVG 16V 20% SMD
C180 72782138 0CE226SF6DC ELECTROLYTIC, 22UF MVG 16V 20% SMD
C189 72782138 0CE226SF6DC ELECTROLYTIC, 22UF MVG 16V 20% SMD
C209 72782138 0CE226SF6DC ELECTROLYTIC, 22UF MVG 16V 20% SMD
C211 72782138 0CE226SF6DC ELECTROLYTIC, 22UF MVG 16V 20% SMD
C215 72782138 0CE226SF6DC ELECTROLYTIC, 22UF MVG 16V 20% SMD
C241 72782138 0CE226SF6DC ELECTROLYTIC, 22UF MVG 16V 20% SMD
C242 72782138 0CE226SF6DC ELECTROLYTIC, 22UF MVG 16V 20% SMD
*The availability of some parts listed is subject to the condition applied.

- 18 -
Location Parts No. Reference Description
No.
C259 72782138 0CE226SF6DC ELECTROLYTIC, 22UF MVG 16V 20% SMD
C276 72782142 0CE227SC6DC ELECTROLYTIC, 220UF MVG 6.3V 20% S
C311 72782142 0CE227SC6DC ELECTROLYTIC, 220UF MVG 6.3V 20% S
C321 72782132 0CE106SF6DC ELECTROLYTIC, 10UF MVG 16V 20% R/T
C400 72782131 0CE105SK6DC ELECTROLYTIC, 1UF MVG 50V 20% SMD
C402 72782153 0CE476SF6DC ELECTROLYTIC, 47UF MVG 16V 20% SMD
C403 72795164 0CC221CK41A CERAMIC, 220PF 1608 50V 5% R/
C404 72782153 0CE476SF6DC ELECTROLYTIC, 47UF MVG 16V 20% SMD
C405 72782138 0CE226SF6DC ELECTROLYTIC, 22UF MVG 16V 20% SMD
C406 72782135 0CE107SF6DC ELECTROLYTIC, 100UF MVG 16V 20% SM
C407 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C408 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C409 72782116 0CK103CK56A CERAMIC, 0.01UF 1608 50V 10%
C410 72782153 0CE476SF6DC ELECTROLYTIC, 47UF MVG 16V 20% SMD
C411 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C412 72782119 0CK105CD56A CERAMIC, 1UF 1608 10V 10% R/T
C413 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C414 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C415 72782132 0CE106SF6DC ELECTROLYTIC, 10UF MVG 16V 20% R/T
C416 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C417 72782153 0CE476SF6DC ELECTROLYTIC, 47UF MVG 16V 20% SMD
C418 72782142 0CE227SC6DC ELECTROLYTIC, 220UF MVG 6.3V 20% S
C420 72782131 0CE105SK6DC ELECTROLYTIC, 1UF MVG 50V 20% SMD
C422 72782142 0CE227SC6DC ELECTROLYTIC, 220UF MVG 6.3V 20% S
C423 72782142 0CE227SC6DC ELECTROLYTIC, 220UF MVG 6.3V 20% S
C426 72782149 0CE475SK6DC ELECTROLYTIC, 4.7UF MVG 50V 20% SM
C434 72782149 0CE475SK6DC ELECTROLYTIC, 4.7UF MVG 50V 20% SM
C435 72782149 0CE475SK6DC ELECTROLYTIC, 4.7UF MVG 50V 20% SM
C440 72782149 0CE475SK6DC ELECTROLYTIC, 4.7UF MVG 50V 20% SM
C441 72782149 0CE475SK6DC ELECTROLYTIC, 4.7UF MVG 50V 20% SM
C443 72782138 0CE226SF6DC ELECTROLYTIC, 22UF MVG 16V 20% SMD
C445 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C446 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C447 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C448 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C449 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C450 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C452 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C454 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C455 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C456 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C481 72782138 0CE226SF6DC ELECTROLYTIC, 22UF MVG 16V 20% SMD
C482 72782138 0CE226SF6DC ELECTROLYTIC, 22UF MVG 16V 20% SMD
C511 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C515 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C517 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C519 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C523 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C526 72782146 0CE336SH6DC ELECTROLYTIC, 33UF MVG 25V 20% SMD
C527 72782146 0CE336SH6DC ELECTROLYTIC, 33UF MVG 25V 20% SMD
C528 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C529 72782146 0CE336SH6DC ELECTROLYTIC, 33UF MVG 25V 20% SMD
C530 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C531 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C532 72782146 0CE336SH6DC ELECTROLYTIC, 33UF MVG 25V 20% SMD
C533 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C535 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C554 72782153 0CE476SF6DC ELECTROLYTIC, 47UF MVG 16V 20% SMD
C555 72782133 0CE106SH6DC ELECTROLYTIC, 10UF MVG 25V 20% SMD
C556 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C557 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C569 72782135 0CE107SF6DC ELECTROLYTIC, 100UF MVG 16V 20% SM
C575 72782132 0CE106SF6DC ELECTROLYTIC, 10UF MVG 16V 20% R/T
C576 72782132 0CE106SF6DC ELECTROLYTIC, 10UF MVG 16V 20% R/T
C580 72782145 0CE335SK6DC ELECTROLYTIC, 3.3UF MVG 50V 20% SM
C590 72782145 0CE335SK6DC ELECTROLYTIC, 3.3UF MVG 50V 20% SM
C598 72782138 0CE226SF6DC ELECTROLYTIC, 22UF MVG 16V 20% SMD
C600 72782132 0CE106SF6DC ELECTROLYTIC, 10UF MVG 16V 20% R/T
C601 72782132 0CE106SF6DC ELECTROLYTIC, 10UF MVG 16V 20% R/T
C602 72782132 0CE106SF6DC ELECTROLYTIC, 10UF MVG 16V 20% R/T
C603 72782132 0CE106SF6DC ELECTROLYTIC, 10UF MVG 16V 20% R/T
C604 72782145 0CE335SK6DC ELECTROLYTIC, 3.3UF MVG 50V 20% SM

- 19 -
Location Parts No. Reference Description
No.
C605 72782132 0CE106SF6DC ELECTROLYTIC, 10UF MVG 16V 20% R/T
C606 72782132 0CE106SF6DC ELECTROLYTIC, 10UF MVG 16V 20% R/T
C607 72782132 0CE106SF6DC ELECTROLYTIC, 10UF MVG 16V 20% R/T
C608 72782132 0CE106SF6DC ELECTROLYTIC, 10UF MVG 16V 20% R/T
C609 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C610 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C611 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C612 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C613 72782145 0CE335SK6DC ELECTROLYTIC, 3.3UF MVG 50V 20% SM
C614 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C615 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C616 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C617 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C618 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C619 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C620 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C621 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C622 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C623 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C624 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C625 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C626 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C627 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C628 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C629 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C630 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C631 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C632 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C633 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C634 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C635 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C636 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C637 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C638 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C639 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C640 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C641 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C642 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C643 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C644 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C645 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C646 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C647 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C648 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C649 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C650 72796129 0CC270CK41A CERAMIC, 27PF 1608 50V 5% R/T
C651 72796129 0CC270CK41A CERAMIC, 27PF 1608 50V 5% R/T
C652 72796129 0CC270CK41A CERAMIC, 27PF 1608 50V 5% R/T
C653 72796129 0CC270CK41A CERAMIC, 27PF 1608 50V 5% R/T
C654 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C655 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C700 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C701 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C702 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C704 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C706 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C707 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C709 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C710 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C711 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C712 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C713 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C714 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C715 72782135 0CE107SF6DC ELECTROLYTIC, 100UF MVG 16V 20% SM
C716 72782146 0CE336SH6DC ELECTROLYTIC, 33UF MVG 25V 20% SMD
C717 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C718 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C719 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C720 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C721 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C722 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C723 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R

- 20 -
Location Parts No. Reference Description
No.
C724 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C725 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C726 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C727 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C728 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C729 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C730 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C731 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C732 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C733 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C734 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C735 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C736 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C737 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C738 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C739 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C740 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C741 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C742 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C743 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C744 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C745 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C746 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C747 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C748 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C749 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C750 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C751 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C752 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C753 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C754 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C755 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C756 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C757 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C758 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C759 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C760 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C761 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C762 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C763 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C764 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C765 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C766 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C767 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C768 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C769 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C770 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C771 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C772 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C773 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C774 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C775 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C776 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C777 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C778 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C779 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C780 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C783 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C784 72782146 0CE336SH6DC ELECTROLYTIC, 33UF MVG 25V 20% SMD
C800 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C801 72782094 0CQZVBK002C DRAWING, A.C 275V 0.22UF K (S
C802 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C803 72782094 0CQZVBK002C DRAWING, A.C 275V 0.22UF K (S
C804 72782132 0CE106SF6DC ELECTROLYTIC, 10UF MVG 16V 20% R/T
C805 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C806 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C807 72782113 0CK10202510 CERAMIC, 1000PF D 2KV 10% B(Y
C808 72782111 0CC680CK41A CERAMIC, 68PF 1608 50V 5% R/T
C809 72782111 0CC680CK41A CERAMIC, 68PF 1608 50V 5% R/T
C810 72782115 0CK1030K945 CERAMIC, 0.01UF D 50V 80%, -20
C811 72782118 0CK104CF56A CERAMIC, 0.1UF 1608 16V 10% R
C812 72782096 181-007H DRAWING,MPEECQ-V1H474JL3(TR