TouchTunes Media Player FRU User manual

Purpose
This document explains how to install the Camera Assembly Field Replacement Unit (FRU) kit (P/N 600273-001)
for an Angelina jukebox.
Topics
•Required Tools and Equipment
•Important Safety Information
•Included in This Kit
•Replacing the Camera Assembly
•Aligning the Camera
•Setting the Camera’s White Balance
•Contacting TouchTunes Technical Support
Required Tools and Equipment
• Measuring tape
• Phillips head screwdriver, #1
• Cable ties, if not included in this kit
• Cutting tool (to cut existing cable ties)
• Anti-static wrist band
• Several blank sheets of white paper (for the calibration procedure)
Audience
• TouchTunes Angelina jukebox operators and
technicians
• TouchTunes Field Service and Customer Support
Estimated Time
15 minutes
Required Personnel
1 technician
This document includes tasks of the following
types:
Software
Hardware
Mechanical



FRU Installation Guide
Replacing Angelina’s Camera Assembly
May 2018
901070-001
Rev 00

2Replacing Angelina’s Camera Assembly
Important Safety Information
Important Safety Information
To avoid damaging the camera, it is important to prevent exposure to static discharge during installation.
TouchTunes strongly recommends you follow these guidelines during installation.
• Wear a grounded anti-static wrist strap, or work with one hand always touching a metal part of the metal
chassis.
• Whenever possible, leave the camera laying on an anti-static bag or anti-static foam.
• Leave the jukebox plugged into the AC outlet with the power switch turned OFF. Doing so places a ground
on the metal chassis.
Included in This Kit
Ensure that you have received all required parts before proceeding with this installation.
Replacing the Camera Assembly
To replace the defective camera assembly:
1. Unlock and open the jukebox door.
2. Press the MNGR button on the I/O Board to open the Operator interface main menu.
3. On the Angelina screen, press the REBOOT button.
NOTE For warranty returns, place the defective unit into the packaging/container from which
you removed the replacement unit. Do not disassemble the defective unit. Doing so
voids its warranty.
You must obtain a valid Return Authorization (RA) number from TouchTunes before
shipping a defective unit.
Part Quantity TouchTunes Part #
Camera Assembly 1 401552-001
Fasteners 2 200020-008
FRU Manual: Camera Assembly (this document) 1 901070-001
WARNING: When performing this procedure or any other maintenance on your jukebox, the unit
must be powered off.

3Replacing Angelina’s Camera Assembly
Replacing the Camera Assembly
4. When you hear the BIOS beep, power down Angelina by setting the rocker switch on the Power Supply Unit
(PSU) to the off (O) position.
5. Snip the cable tie holding the cables together to the right of the existing camera assembly, if needed.
6. Disconnect the cable that connects the existing camera assembly to the Angelina computer USB port.
7. Loosen the middle calibration screw.
Loosen middle calibration screw
WARNING: Never shut down or unplug Angelina without first performing a reboot and waiting
for the BIOS beep. Doing so can cause damage to the hard drive and make it unusable.
IMPORTANT: Leave the jukebox plugged into the AC outlet while turned off. This grounds the
metal chassis.

4Replacing Angelina’s Camera Assembly
Replacing the Camera Assembly
8. Remove the two screws that fasten the existing camera assembly to Angelina and set them aside. Note that
when removing the second screw, you should support the camera assembly to ensure it does not fall (as
shown in the following figure).
Removing second screw
9. Remove the existing camera assembly from the jukebox.

5Replacing Angelina’s Camera Assembly
Replacing the Camera Assembly
10. Take the replacement camera assembly (which consists of the camera mounted on a bracket with a USB
cable connected) out of its packaging.
Replacement camera assembly
11. Remove the lens cap from the camera.
12. Fit the camera assembly onto the two studs and fasten it using the two screws you removed earlier.
NOTE The cable should extend from the camera assembly from its right side. If the
cable is extending from the left, then the camera assembly is upside-down.

6Replacing Angelina’s Camera Assembly
Replacing the Camera Assembly
13. Connect the camera’s cable to the USB port on the Angelina computer.
USB cable plugged into Angelina computer

7Replacing Angelina’s Camera Assembly
Replacing the Camera Assembly
14. Route the cable over and towards the right of the monitor.
Cable routing
15. Use the cable ties supplied with the camera kit to fasten the USB cable to the existing bundle of cables. If
cable ties are not included in the kit, use self-provided ties.
16. Power up Angelina by setting the rocker switch on the PSU to the on position (l).
NOTE Since you have not yet aligned the camera, it is normal and expected that the
camera lens does not line up with the circular aperture on the outside of the
Angelina door. Centering the lens is part of the next step of the installation,
Aligning the Camera.

8Replacing Angelina’s Camera Assembly
Aligning the Camera
Aligning the Camera
Before you proceed with the camera calibration, it is critical that the Angelina jukebox be mounted at the correct
height.
The top of the Angelina bracket should be 62 inches from the floor. The correct height is necessary to avoid
damage to the bracket and to achieve the correct calibration.
Wall bracket height
If your Angelina jukebox is not mounted at this height, consult the Angelina Installation and Setup Guide for
mounting instructions.
To properly align the camera, you must use the Video Capture Test utility on the Operator menu.
1. On the I/O Board, press the MNGR button to open the Operator menu.
2. From the main menu, select HARDWARE and then press the Camera button. The preview area displays the
field of view being captured by the camera.
3. If part of the image is obscured or presents a “tunnel vision” effect, you will have to adjust the position of the
camera.
4. Put a mark on the floor 152 inches away from the wall, centered with the Angelina jukebox.
5. Turn the screw in the middle of the camera bracket on the rear of the bracket until you see the mark on the
floor at the bottom of the preview area.
6. The camera lens and the aperture on the exterior of the Angelina jukebox door should align vertically more
and more as you adjust the camera screw using the method above.

9Replacing Angelina’s Camera Assembly
Setting the Camera’s White Balance
Setting the Camera’s White Balance
Now that you have installed and aligned the camera’s firmware, you must set the camera’s white balance to
optimize the coloration of its images.
1. Stand at arm’s length from the Angelina screen. This simulates the optimal distance a patron’s face would be
positioned from the camera.
2. From the Operator interface, go to HARDWARE > Camera and then press the WHITE BALANCE button.
The Preview screen will display a red square.
3. Hold up a stack of white or light gray paper and position it at a 45 degree angle backwards (that is, tilting the
top towards yourself). Do not use a single sheet of paper as it may be translucent. The entirety of the red
square should be filled on screen by your sheet and you should be reflecting the ceiling light towards the
camera.
Setting white balance
4. The white balance process will take approximately 5 seconds. Keep the sheet as still as possible during this
time.
You have now completed the replacement of the camera assembly.
NOTE If the location generally operates under low-lighting conditions, it is essential to
replicate these lighting conditions when performing the white balance
procedure.
NOTE If the lighting of the location changes significantly and permanently, you should
reset the white balance as part of your routine when visiting the location.

Copyright © 2018 The Octave Music Group, Inc. (formerly known as TouchTunes Interactive Networks, Inc.)
The Octave Music Group, Inc.
7250 Mile End, Suite 202
Montreal, Quebec,
Canada, H2R 3A4
The Octave Music Group, Inc.
850 Third Ave, 15th Floor
New York, NY 10022
USA
Technical Support
888-338-5853
www.touchtunes.com
10 Replacing Angelina’s Camera Assembly
Contacting TouchTunes Technical Support
Contacting TouchTunes Technical Support
If you need help or have questions about this guide, call the TouchTunes 24/7 Service Hotline at 888-338-5853.
To help us assist you more effectively with problem reports, the following information may be required when
contacting TouchTunes support:
• Jukebox model and ID
• Operator ID
• Serial number of the component you believe to be defective
• Date/time of the problem
• Actions performed immediately before the problem occurred
• Any additional comments relevant to the problem