TP-Link M7000 User manual

d. Note down the default SSID and Wireless
Password. Then replace the cover.
a. Remove the back cover. b. Install your SIM card.
SSID: TP-Link_XXXX
WirelessPassword: XXXXXXXX
c. Install the provided battery.
SSID: TP-Link_XXXX
WirelessPassword: XXXXXXXX
1
2
1. Install the SIM Card and Battery
· If you cannot access the internet, refer to FAQ > Q1.
·By default, Power Saving is enabled and the Mobile Wi-Fi will turn o Wi-Fi when no wireless devices are connected to it for 10 minutes.
To resume the Wi-Fi connection, press the Power button.
!
2. Connect to the Internet
©2020 TP-Link 7106508955 REV3.0.0
!
The LEDs will turn o automatically after idling for 30 seconds. To check the LED
status, press the Power button to turn them on again.
LED Indicators
Solid Green
Blinking Red
Blinking Green
O
On/O
On/O
Status Explanation
Wi-Fi is enabled or disabled.
Internet service is available or unavailable.
LED
(Battery)
(Wi-Fi)
(Internet)
* Images are for demonstration only.
b. Connect your wireless device to the Mobile Wi-Fi using the
SSID and the Wireless Password you have noted down.
a. Press and hold the Power button
to power on the Mobile Wi-Fi.
SSID:
TP-Link_XXXX
Wireless Password:
XXXXXXXX
Wi-Fi
Wi-Fi
TP-Link_XXXX
CHOOSE A NETWORK...
Other...
< Settings
Enjoy the internet!
Quick Installation Guide
Mobile Wi-Fi
SSID:
TP-Link_XXXX
WirelessPassword:
XXXXXXXX
SSID:TP-Link_XX XX
WirelessPassword: XXXXXXXX
SSID:
TP-Link_XXXX
Wireless Password:
XXXXXXXX
+ +
SIM card requirement:
!
+ +
Micro SIM card +
Provided Micro SIM card adapter + Provided sticker
Standard
SIM card
Nano SIM card +
Provided Nano SIM card adapter + Provided sticker
Mobile Wi-Fi has enough power or is fully charged.
The battery level is lower than 10%.
Mobile Wi-Fi is charging.
Power is o.

FAQ (Frequently Asked Questions)
· Keep the device away from water, re, humidity or hot environments.
· Do not attempt to disassemble, repair, or modify the device. If you need service,
please contact us.
· Do not use the device where wireless devices are not allowed.
· Do not disassemble, crush, puncture, short external contacts, or dispose of the
battery in re or water.
· Do not leave a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of ammable liquid or
gas. Do not leave a battery subjected to extremely low air pressure that may
result in an explosion or the leakage of ammable liquid or gas.
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE.
Please read and follow the above safety information when operating the device.
We cannot guarantee that no accidents or damage will occur due to improper
use of the device. Please use this product with care and operate at your own risk.
Safety Information
Charging Your Mobile Wi-Fi
!· The Battery LED will be solid green when the Mobile Wi-Fi is fully charged.
·The power adapter is not provided by TP-Link.
5V/1A
Method 1
Via a Wall Outlet (Recommended)
Method 2
Via a Computer
Managing Your Mobile Wi-Fi
tpMiFi App
1. Get the tpMiFi app from App Store or Google Play, or by
scanning the QR code.
2. Connect your wireless device to the Mobile Wi-Fi.
3. Launch tpMiFi and enter admin to log in.
Web Management Page
1. Connect your wireless device to the Mobile Wi-Fi. If it is a computer,
make sure it is set to obtain an IP address automatically.
2. Launch a web browser and visit http://tplinkmi.net or
http://192.168.0.1. Enter admin to log in.
For technical support, user manuals and more information,
please visit https://www.tp-link.com/support, or simply
scan the QR code.
Manage your Mobile Wi-Fi using any of the methods below. You can customize Wi-Fi settings, block Wi-Fi devices and more.
· Check the Data Roaming settings
If your SIM card is operated in a roaming service area, go to Dial-up, enable
Data Roaming and tap Done.
· Check Mobile Data
Go to Dial-up to verify that Mobile Data is On. If not, enable it and tap Done.
· Check Data Limit
Go to Device > Data Usage Settings to check whether your data usage has
exceeded the Total/Monthly allowance.
Q2. How do I restore the Mobile Wi-Fi to its factory default settings?
A. With the Mobile Wi-Fi powered on, remove the cover, then use a pin to
press and hold the Reset button until all LEDs turn on momentarily.
Note: Restoring the device to its factory defaults will clear all your settings.
Q1. What should I do if I cannot access the internet (the Internet
LED doesn’t light up)?
A. Visit the web management page (http://tplinkmi.net) on your phone,
enter admin to log in, then check the following:
· Check PIN status
If the current SIM card status is PIN Locked, your SIM card is PIN
protected and you need to unlock it using the PIN code provided by your
mobile carrier.
· Verify the mobile carrier parameters
1. Go to Dial-up, tap View prole details,and verify that the parameters
(i.e. APN, username and password) provided by your mobile carrier are
correct.
2. If the parameters are not correct, return to the Dial-up page and
create a new prole with the correct information.