TRACE ELLIOT Transit B User manual

Trace Elliot® Transit B
Bass Instrument Preamp
Owner’s Manual

FCC Compliancy Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, that may cause undesired operation.
Warning: Changes or modications to the equipment not approved by Peavey Electronics
Corp. can void the user’s authority to use the equipment.
Note - This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try and correct the interference by one or more of the following
measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3(B)/NMB/3(B)
Trace Elliot • Hwy. 5022 Hwy. 493 North • Meridian, MS 39305
Tel: [phone] • Fax: [phone] • www.traceelliot.us

3
Congratulations on your purchase of the all-new Trace Elliot Transit B Bass Guitar Pre-amp pedal! The Transit-
B pedal is a professional grade pre-amp for the discerning bassist. Built-in tools for tone shaping like Pre-
shape, 5 band active EQ and dual band Compressor are easy to use and easy to tweak on the y. Features like
Drive with blend control and built-in bass enhancement add to tonal options available. The back-lit control
panel becomes the chromatic Tuner for accurate tuning. Built-in Pre and Post XLR balanced output, dry output
and headphone output give the user the ins and outs they need for the best live coverage. e pre and post
DI outputs make sure your tone is THE tone, and stays consistent night aer night. e Transit B pedal was
also designed to t in your case or bag, making it the perfect travel companion. e controls are simple and
intuitive, making ne adjustments easy. Please read this manual carefully so you can get the most out of your
new Trace Elliot product!
FEATURES:
•Color coordinated backlit controls
•Passive/Active switch
•Pre-shape switch for the classic Trace Elliot EQ curve
•Drive control with blend knob, foot-switchable
•5 band EQ with defeat switch
•Dual band compressor with defeat switch
•Mute/Tune switch
•Built-in chromatic tuner
•Input Gain and Output Level controls
•Line level, instrument level and dry outputs
•Pre and Post balanced XLR outputs with Ground Lift
•Aux input
•Headphone output
•Dimensions (pedal only): 312mm W x 114mm D x 58.4mm H (12.3” W x 4.5” D x 2.3” H)
•Weight: 1.18 kg (2.6 lbs; pedal only), 1.45 kg (3.2 lbs; pedal + bag + supply)
Caution: Please look over this guide and read any caution or warning statements found within. Following
these warnings is crucial to your personal safety and the safety of your Trace Elliot product.
TRACE ELLIOT®TRANSIT™-B
PRE-AMP
ENGLISH

4
Top Panel
1
6 1310 117 8 9 12 14
2 43 5
(1) OUTPUT LEVEL
Controls the output level of the pre-amp. It does not aect the XLR direct outs. is allows you to adjust the
1/4” outs for stage rig, while not aecting the PA level.
(2) LO-BAND/HI-BAND
Controls the amount of compression to the Lo-Band and Hi-Band frequencies. e backlit LEDs come on with
the footswitch, but each will icker o while playing to show when compression occurs.
(3) 5-Band Equalisation controls
Controls the equalisation of the pre-amp. e green LED behind the MID knob will turn red if clipping occurs
in the EQ circuit due to too much boost. Adjust EQ accordingly.
(4) Drive/Blend controls
Controls the amount of Gain for the Drive signal. e Blend control controls the blend of the Drive signal with
the Clean signal.
(5) INPUT GAIN
Controls the input signal recieved from the instrument. e backlit LED turns red to indicate clipping. You
should ideally set the knob as high as you can while still avoiding clipping.
(6) BASS ENHANCEMENT Switch and LED
Incorporates a proprietary subharmonic generator circuit that is specially voiced for deep bass. If you are
driving a system with with no subwoofer or limited low frequency capabilities, then this switch may cause the
speakers to be overdriven at the extent of the low frequency response.
(7) MUTE/TUNE Switch
Mutes the pre-amp signal and activates the onboard tuner (11).
(8) COMPRESSION Switch
Activates the pre-amp’s Lo-Band and Hi-Band compression.

5
(9) EQUALISATION Switch
Allows user to bypass the on-board EQ.
(10) PRE and POST Compression Switch and LED
Allows user to choose whether to add compression to the signal before the EQ or aer.
(11)TUNER Display
Activates when the MUTE/TUNE switch (7) is pressed. e note being played is displayed and the LEDs on
the above knobs indicate whether the note is too at or sharp. When the center red LED shines alone, the note
is in tune.
(12)DRIVE Switch
Activates the Drive circuit.
(13)PASSIVE/ACTIVE INPUT Switch and LED
Allows user to select the optimum setting for an instrument with either a passive or active pickup.
(14)PRE-SHAPE
Activates the circuit for the classic Trace Elliot®‘Mid Pre-Shape’ that all users of Trace Elliot
graphic style ampliers will recognise immediately. The actual effect of this circuit is to boost the low and
high frequencies (55Hz and 2kHz to 5kHz respectively) and to cut the mid frequencies (centred around
400Hz), giving an instant, clearly dened, punchy sound.

6
Rear Panel
17 18 19 2015 16 21 22 23 24
(15) INPUT JACK
Accepts signal from the instrument cable.
(16) DRY OUT
Provides a buered version of the raw instrument signal to drive additional electronic inputs without loading
of the instrument. is is the only output that does not mute when the tuner is activated - allowing it to drive
an external tuner if preferred.
(17) AUX INPUT
Allows you to connect a media device to the unit and play along.
(18) HEADPHONE OUTPUT
1/8” headphone output for personal monitoring.
(19) DI PRE EQ XLR OUTPUT
e Transit B can be run with a signal source from either pre or post processing. Use this XLR output if the DI
is used in a live setting to send signal directly to a PA system. In this case, the DI signal will not be aected by
changing any of the preamp controls, which allows independent adjustments for the PA system. Output Level
Control (1) DOES NOT aect the output level of this output.
(20) DI POST EQ XLR OUTPUT
e POST EQ setting is useful for recording or connecting the preamp to an external power amplier in a live
application, or directly to a PA, if you want the on-board processing to be heard in the FOH system. Output
Level Control (1) DOES NOT aect the output level of this output.
(21) GND LIFT Switch
is switch may be used to eliminate hum caused by ground loops between the preamp and other equipment,
such as a mixing console.
(22)LINE OUTPUT
Line (high) level unbalanced output for driving the input of a power amp or an eects return.
(23)INST OUTPUT
Instrument (low) level unbalanced output for driving the input of a preamp or a mixer input channel.
(24) DC Input Socket
For connection of the included 9VDC power supply. Please note that the polarity of the center pin in the socket
is negative (-) with respect to ground. Please use the included Trace Elliot® Power Supply. Replacement Part
#000908180.

7

8
Specifications
Weight:
1.6 lb (0.73 Kg)
Dimensions (H x W x D):
1.35” (3.4cm) x 6.75” (17.1cm) x 4.10” (10.4cm)
e following nominal measurements were taken with all controls set at 12 o’clock, unless otherwise noted:
Nominal INPUT level:
PASSIVE = -1.41 dBV
ACTIVE = 4.60 dBV
Maximum INPUT level:
PASSIVE = 4.60 dBV
ACTIVE = 10.9 dBV
INPUT impedance:
PASSIVE = 500k Ohms
ACTIVE = 44k Ohms
Nominal DRY OUT level = 0.00 dBV
Nominal INST OUTPUT level = -10 dBV
INST OUTPUT impedance = 1k Ohms
Nominal LINE OUTPUT level = 1.78 dBV (+4 dBu)
LINE OUTPUT impedance = 1k Ohms
Nominal D.I. PRE level = 1.78 dBV (+4 dBu)
Nominal D.I. POST level = 1.78 dBV (+4 dBu)
EQUALISATION:
BASS = +/- 15 dB @ 117 Hz; Q = 0.91
LO-MID = +/- 15 dB @ 279 Hz; Q = 0.89
MID = +/- 15 dB @ 664 Hz; Q = 0.88
HI-MID = +/- 15 dB @ 1.73 kHz; Q = 0.74
TREBLE = +/- 15 dB @ 4.95 kHz; Q = 0.73
AUX IN level:
Nominal = 1.78 dBV (+4 dBu)
AUX IN input impedance = 10k Ohms
PHONES output level:
Minimum load impedance = 4 Ohms
Maximum output power at minimum load = 500 mW (rms)
COMPRESSION : Two-band compressor with crossover point at 333 Hz and option to place the compressor
either before or aer the EQUALISATION controls in the signal chain.

9
Warranty registration and information for U.S. customers available online at
www.traceelliot.com/warranty
or use the QR tag below
DRIVE : Special valve-emulated overdrive circuit with 50% dry vs. distorted mix when BLEND is set to 12
o’clock.
PRE-SHAPE : e classic and proprietary Trace Elliot bass EQ curve.
Power Supply (included): 9V DC (negative tip) @ 900 mA.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

10
Features and specications are subject to change without notice.
Trace Elliot • Hwy. 5022 Hwy. 493 North • Meridian, MS 39305
Tel: [phone] • Fax: [phone] • www.traceelliot.us ©2016 Printed in U.S.A. 80305734
B