Trans Pac TPH-5500 Series User manual

I. Introduction
The TPH-5500 series Camera Housing is constructed from die-cast aluminum alloy with powder coated finish and is
equipped with an adjustable Fully-Cable-Managed Mounting Bracket. The product is CE certified and has environmental
protection level IP 68 or IP 44 with blower, Reach and RoHS compliance.
II. Mounting Configuration and Dimensions of TPH 5500
User’s Manual
Model No: TPH-5500 Series
Adjust position and direction
III. Fitting instructions for camera.
Inside the internal wiring diagram of TPH 5500 for the
window demister. A spare 6 way terminal block is
provided at the rear of the housing for the camera when
necessary and lens connections. Circuit identified as
follows:
IV. Wiring Diagram
TB.1 6 way terminal block
TB.2 3 way terminal block
FTB.1 Fused terminal block
STAT.1 18℃Thermostat
STAT.2 35℃Thermostat
H.1 Heater
PSU Power Supply Unit
P.C.B.1 Thermal control circuit board
FS.1 3 Amp. Fuse
BR-13 Fully-Cable Managed Bracket
Inner space for camera mount
W60 x H80 x L260mm
Dimensions of Bracket Base
Power supply unit (option)
Camera mounting platform
Heater shield
Heater
Thermal control board
Cable conducts
Terminal block assembly
Blower
Ground wire

!
V. INSTALLATION SUGGESTION:
If you plan to installthis camera into a tropical, sear coastal, saltwater or corrosive industrial water/moist environment,
please seal each stainless steel screw and fittings with a silicon grease compounds. This will help prevent electrolysis
corrosive occurring and extend the lifespan of the camera and housing. The installationof a surge protection device is
strongly recommended in frequent thunder area.
1. Pin1,2 and pin 3,4 is DC 12V output for motor lens, IR illuminator,
siren or speaker use. If no use please remove cable from connector.
2. Pin 5,6 is for DC12V output for camera.
DC output of PSU connectors AC power connection
Shows how to connect the AC power cord to
the FTB. 1 connector.
IMPORTANT NOTE:
1. Disconnect Device: A disconnect device from main supply shall be incorporated in the building installation wiring.
2. Electrical Connections: Only a qualified electrician allow to make electrical connections.
Trans Pacific Industries Corp.
5F, No.79 Jen-Ai Road Section 4, Taipei 106, Taiwan
Tel: [phone] Fax: [phone] http://www.transpac-cctv.com
Features
1. Turn on at 35°C 1. 880 (80-260Vac input, 1x12Vdc output, 1A)
2. Turn off at 25°C 2. 080 (80-260Vac input, 4x12Vdc output, 3.5A)
3. 324 (24Vac input, 4x12Vdc output, 3.5A)
Model No. 4. 424 (24Vac input, 1x12Vdc output, 1.5A)
12Vdc / 24Vac 110 / 230Vac 12Vdc / 24Vac 110 / 230Vac 12Vdc 24Vac 880 080 324 424
5500
5500-12/24HS ●
5500-12/24HD ●
5500-012/F ●
5500-012/HF ● ●
5500-024/F ●
5500-024/HF ● ●
5500-110/230HS ●
5500-110/230HD ●
5500-080/HS ● ●
5500-080/HD ● ●
5500-080/F ● ●
5500-080/HF ● ● ●
5500-080/HC** ●●
5500-324/F ● ●
5500-324/HF ●●●
5500-324/HC** ● ●
5500-880/F ● ●
5500-880/HF ● ● ●
5500-880/HC** ●●
5500-424/F ●●
5500-424/HF ●●●
5500-424/HC** ●●
*First heater prevents moisture on the window glass till weather temperature -25°, second heater is heating in enclosure for camera operation properly till
weather temperature -40°
** With 12Vdc camera jet
PSU (power supply unit)
Turn off at 28°C
2. Turn off at 28°C
Blower (IP44)
Double heaters*
1. Turn on at 18°C
Single heater
1. Turn on at 18°C
2. Turn on at 0°C
Turn off at 10°C
●