TRECE PHEROCON BMSB STKY User manual

GSB lure
BMSB lure
INSECT PHEROMONE & KAIROMONE SYSTEMS
Your Edge – And Ours – Is Knowledge.
1 2 3
A B
STKYTrap
1. Remove release liner from both
sides of the STKYTrap.
3. Attach it to the tree branch. Trap
should be in full contact with
tree branch.
4. Insert the second twist tie through
the opposite corner hole of the trap
and attach it to the tree branch.
2. Insert the rst twist tie through
one corner hole of the trap.
5. Insert the twist tie into one of the holes of the
BMSB lure then through the GSB lure. Next, bend
the BMSB lure to align the second hole and insert
twist tie. Twist the twist tie to keep them tight
together.
6. Continue inserting twist tie through a center
hole of the trap then around tree branch.
NOTE: In order to prevent reduction in pheromone
release, do not press the lures onto the
adhesive on the STKY Trap.
7. Finished trap.
NOTE: Remove all foliage from around the trap
that may come in contact with the trap.
Twist ties
Visit our website: www.trece.com or call 1- 866 -785 -1313
Please see Trécé’s IPM Partner® Guidelines for further instructions.
Materials Needed:
A. (3) Twist ties
B. STKY™ Dual Panel Adhesive Trap
C. PHEROCON® BMSB and GSB lures
© 2018, Trécé Inc., Adair, OK USA • TRECE, PHEROCON, STORGARD, CIDETRAK and IPM PARTNER are registered trademarks of Trece, Inc., Adair, OK USA TRE-1238, 05-18
4
5 76
C
For: Brown Marmorated Stink Bug (BMSB), Halyomorpha halys, and Other Stink Bugs
Green Stink Bug(GSB), Acrosternum hilare, Brown-winged Green Bug, Plauti stali,
and Other Stink Bugs
(See other side for instructions
for ground stake assembly)
TRAP
SWD
BMSB STKY
™
Dual Panel Adhesive Trap Installation Instructions: For Trees
STORAGE RECOMMENDATION: Store in a COLD environment.

INSECT PHEROMONE & KAIROMONE SYSTEMS
Your Edge – And Ours – Is Knowledge.
1
1
2
3
CB
STKY trap
A
Twist ties
1. Remove release liner from both sides of the STKY trap.
3. Insert the twist tie into one of the holes of the BMSB lure then through the
GSB lure. Next, bend the BMSB lure to align the second hole and insert twist
tie. Twist the twist tie to keep them tight together.
2. Attach STKY trap to stake with clip as shown.
4. Make a loop with ends of the twist tie and hang on the binder clip on the
other side of the stake as shown.
NOTE: In order to prevent reduction in pheromone release rate, do not press
the lures onto the adhesive.
Visit our website: www.trece.com or call 1- 866 -785 -1313
Please see Trécé’s IPM Partner® Guidelines for further instructions.
Materials Needed:
A. (3) Twist ties
B. STKY™ Dual Panel Adhesive Trap
C. PHEROCON® BMSB and GSB lures
D. Flat wooden stake and
binder clip (not included)
© 2018, Trécé Inc., Adair, OK USA • TRECE, PHEROCON, STORGARD, CIDETRAK and IPM PARTNER are registered trademarks of Trece, Inc., Adair, OK USA TRE-1238, 05-18
4
D
NOT INCLUDED
Flat wooden stake with hole near
the top and binder clip
(See other side for instructions
for tree branch assembly)
Dual Panel Adhesive Trap Installation Instructions: For Ground Stake
TRAP
SWD
BMSB STKY
™
For: Brown Marmorated Stink Bug (BMSB), Halyomorpha halys, and Other Stink Bugs
Green Stink Bug(GSB), Acrosternum hilare, Brown-winged Green Bug, Plauti stali,
and Other Stink Bugs
GSB Lure
Front of the trap Back of the trap
BMSB Lure
STORAGE RECOMMENDATION: Store in a COLD environment.