Treestand WMTS-15R Instruction Manual

Distributed by Tahsin Industrial Corp. USA 685 Route 10 East, Randolph, NJ 07869
Every year serious injury and even death occurs from hunting related falls. To ensure your safety, please COMPLETELY read and follow
this safety manual and ALL warning labels BEFORE assembling, installing or utilizing this product.
DO NOT USE THIS PRODUCT BEFORE FULLY UNDERSTANDING ALL SAFETY WARNINGS AND INSTRUCTIONS. IF YOU HAVE
QUESTIONS, ARE UNSUREABOUTANY INFORMATION OR NEED ADDITIONAL INFORMATION CONCERNING YOUR PRODUCT,
CONTACT OUR CUSTOMER SERVICE DEPARTMENTAT 1-866-972-6168 OR VISIT WWW.TREESTANDCUSTOMERSERVICE.COM.
KEEPAND MAINTAIN THIS SAFETY AND INSTRUCTION MANUAL INA SAFE LOCATION FOR FUTURE REFERENCE.
SAFETY MUST BE YOUR FIRST PRIORITY WITH THIS PRODUCT
Warning
MODEL: WMTS-15R
15 FT. TRIPOD
• Weight Limit 300 lbs.
• Do Not Over Tighten Fasteners
F
B
C
N
P
O
M
K
J
E
A
D
P
P
P
L
K
H
Q
R
V
U
X
S
W
T
T
T
K
G
©2012 (rev. 10/11)
Tools Required
Adjustable Wrench
Instruction and Safety Manual

Customer Service Department 1-866-972-6168
TREESTAND SAFETY WARNINGS
Please read the following instruction manual and warnings labels completely before utilizing this product. Failure to understand and execute the instructions
and warnings may result in serious injury or death. In the event of an accident, have a plan for rescue, including the use of devices that may be easily reached
while suspended.
ALWAYS read and understand all warnings and instructions and use all safety products provided before each use of this product. Failure to read and
understand all warnings and instructions may result in serious injury or death. Contact a Customer Service Representative with any questions you may have.
NEVER exceed total weight limit of 300 lbs. DO NOT use if your combined weight with all of your hunting gear and any accessories exceeds 300 lbs. Use of
tree stand over the weight limit may result in serious injury or death.
DO NOT use this tree stand while under the influence of alcohol, medication or any illegal substances. Use of tree stand while under the influence of any of
these substances may result in serious injury or death.
NEVER use this treestand during inclement weather. DO NOT use tree stand during thunderstorms, snowstorms, hurricanes, tornadoes or any other weather
conditions that include (but not limited to) lightning, icy conditions, or high winds that could create slippery or dangerous situations. End your hunt and return to
the ground if inclement weather conditions arise.
NEVER use treestand If you are feeling ill, nauseous, dizzy or if you have a prior condition that could cause a problem. i.e., heart condition, joints that lock-up
spinal fusions, etc., or if you are not well rested and alert. Physical ailments can reduce your ability to safely install, utilize, and remove your treestand. Please
consult a physician prior to use.
NEVER use this tree stand if you have a history of health problems such as (but not limited to) heart problems, back problems, high blood pressure, impaired
vision, equilibrium impairments, are afraid of heights, have been advised by a doctor or physician not to climb. If you are not physically fit, well rested, and
alert, or if you have any other physical or mental condition that would impair your ability to properly use this treestand.
NEVER use this tree stand on a tree that is dead, leaning, diseased, loose barked or on a utility pole as the tree may fall, break, or uproot and may result in
serious injury or death. NEVER rely on a branch for support.
NEVER jump or bounce on the treestand’s platform or ladder sections to seat it to the tree. Instead, step firmly on the first rung of the bottom ladder section to
set the ladder into the ground before proceeding to climb the ladder.
NEVER transport any of your equipment with yourself while ascending or descending the tree. You will need to have two hands free during ascending and
descending for safety. Use a haul line to pull up your firearm (unloaded, chamber opened with safety lock engaged, barrel facing towards the ground), bows,
arrows, knives or any other equipment to your tree stand once you have reached your desired hunting height. ONLY pull up hunting equipment after the tree
stand has been secured to the tree and after you and your harness have been secured to the tree. Prior to descending, lower your equipment on the opposite
side of the tree from which you are climbing. Make sure that the unloaded firearm’s safety lock is engaged and the gun barrel is pointing towards the ground.
ALWAYS hunt with a plan and a buddy. Before you leave home, let others know your exact location, when you plan to return and who is with you.
ALWAYS carry emergency signal devices such as a cell phone, walkie-talkie, whistle, signal flare, PLD (personal location device) and flashlight with you at all
times and within reach even while you are suspended in your harness. Watch for changing weather conditions. In the event of an accident, remain calm and
seek help immediately.
ALWAYS inspect the tree stand and the Fall Arrest System (FAS) (Harness) for signs of wear or damage BEFORE each use. Also inspect to ensure that nuts
and bolts are secure. Pay special attention to the harness and straps, guaranteeing that nothing has been frayed or severed. Destroy all products that cannot
be repaired by the manufacturer. Contact a Customer Service Representative for replacement parts. The Fall Arrest System MUST be discarded and replaced
after a fall has occurred.
DO NOT ATTACH YOUR FULL BODY HARNESS TO YOUR TREESTAND.
NEVER modify your treestand in any way by making repairs, replacing parts, or altering adding or attaching anything to it except if explicitly authorized in
writing by the manufacturer. Improper installation or adjustment may cause serious injury or death. Remove all contents from box. Inspect for any damaged or
missing parts. If any parts are missing or damaged, you must only use certified replacement parts. Using any other replacement parts will
void product warranty. THERE ARE NO EXTRA PARTS. All parts MUST be used to ensure the safety of you and your stand. If you think parts are missing or
damaged, STOP IMMEDIATELY and contact our Customer Service Department. Using the tree stand with missing or damaged parts may result in serious
injury or death. DO NOT return this product to the retailer. Contact a Customer Service Representative if you have any missing, damaged or extra parts.
PRACTICE installing, adjusting and using your treestand at ground level prior to using it at an elevated position.
ALWAYS keep instructions (written and video) in a safe place and review before each use. It is the responsibility of the treestand owner to furnish the complete
instructions to anyone who borrows or purchases the treestand from you. A safe treestand hunting video has been included. Please view it in it’s entirety prior
to using this product.
NEVER use this treestand for any use other than hunting. Our treestands are designed for hunter’s to wear a Full Body Harness. If you are not completely
comfortable and confident with your ability to safely install, ascend, hunt and descend using a Full Body Safety Harness and this treestand, DO NOT
PROCEED.
NEVER use this treestand for trimming trees.
NEVER fall asleep in your stand as you may fall out resulting in serious injury or death.
ALWAYS be sure to retighten all bolts BEFORE each new use of treestand.
ALWAYS have a minimum of three people present when installing or removing this treestand.
©2012 (rev. 12/11)
www.treestandcustomerservice.com

Customer Service Department 1-866-972-6168
TREESTAND SAFETY WARNINGS
NEVER remove any safety warning
stickers from this product.
Safety must be your first priority
during the use of this product.
NEVER adjust your stand while in use. Practice the attachment of this treestand at ground level before using in a hunting environment. ALWAYS ensure that
you and your treestand are safely secured to a healthy tree. Your tree stand MUST be attached tightly to the tree and secured in place. If the stand is not secure,
it may shift while in use, resulting in serious injury or death.
The Installation Cross Straps and Stabilizer Bar(s) MUST be properly installed before each use of the treestand.
ALWAYS inspect every ladder section connection every time you use the stand before you leave the ground. If ladder sections are separating, with the help of at
least two other people, lower the stand to the ground, make adjustments, and reinstall.
ALWAYS check the ground below the tree stand to make sure it is firm and level. Sloping ground or uneven terrain (one side of a rock or root) can cause your
tree stand to tilt or shift.
ALWAYS maintain three points of contact when climbing the tree stand. (Two feet and one hand or one foot and two hands.)
ALWAYS lean forward as you climb and attach your harness to the tree before securing the platform to the tree and stepping onto the platform.
DO NOT leave your treestand outside since weather or animals may cause damage. Tree growth can also cause stress and damage straps and buckles. It must
be stored inside when not in use.
NEVER wear jewelry or loose fitting clothing, which can cause hazardous conditions. Clothing may be caught in your equipment and cause you to fall. You must
always wear non-slip or rubber boots. Shoelaces must be tucked into your boots. Rings and necklaces MUST NOT be worn.
NEVER use this treestand with a second person. The treestand is designed for use by ONE person.
NEVER let children play with or use this treestand without adult supervision. This treestand is not a toy. No one under the age of 18 should attempt to use this
product without direct adult supervision.
DO NOT use tree stand if any nuts or bolts or parts are loose, bent, or crooked.
ALWAYS know your physical limitations. Don’t take chances. If you start thinking about how high you are, don’t go any higher. Instead, choose a minimum
height that will allow for safe, effective and comfortable hunting.
ALWAYS lean forward towards the tree as you climb and attach your harness to the tree BEFORE securing the platform to the tree and stepping onto the
platform. NEVER lean out from the treestand for any reason.
ALWAYS wear a Fall Arrest System (FAS) (Harness) consisting of a full body safety harness after leaving the ground. ATMA Certified Full Body Harness MUST
always be connected to yourself and the tree during ascending, hunting and descending. Single safety belts and chest harnesses are no longer allowed and
should NEVER be used. If you are not wearing a Full Body Harness properly attached to the tree, that is protecting you from a fall, DO NOT leave the ground.
Failure to wear your Full Body Harness may result in serious injury or death.
Be aware that falls can occur at anytime after leaving the ground.
ALWAYS read and understand the manufacturer’s Warnings, expiration date (if applicable) and instructions on how to use and how to properly adjust the
harness. Practice the use of a full body safety harness at ground level in the presence of a responsible adult to experience the feeling of hanging suspended
before using in a hunting environment. Failure to follow harness instructions may result in not being able to return to the stand and being suspended in a
harness after a fall, or serious injury or possibly death. If the hunting location is unknown by anyone and communication efforts are unsuccessful, you MUST
have a personal plan for rescue/escape because prolonged suspension in a harness may be fatal. It is important to exercise the legs by pushing against the tree
or doing other forms of continuous leg exercises to avoid blood pooling while being suspended. Hunters with varying degrees of physical fitness may require
different plans to recover/escape the effects of prolonged suspension. Have a personal plan and practice it in the presence of a responsible adult before leaving
the ground. No one escape/rescue plan will work for every hunter on every tree in every circumstance. Only you can determine the best recovery/escape plan
for your situation before leaving the ground.
ALWAYS have a suspension relief device on your person and readily accessible while using a harness. These devices allow the user to relieve the load on the
lower extremities if suspended in a harness and help maintain circulation in the legs, mitigate suspension trauma (blood pooling) or allow descent to the ground.
Several optional products/systems are available that offer self-recovery or self-extraction from a fall when suspended in a harness. Some systems automatically
descend the user while others allow user control. One of these products/systems can be considered for use as an additional safety precaution against prolonged
suspension and suspension trauma, Be sure to follow the manufacturers’ instructions on the safe use of these products/systems.
Hunt from the ground when self-recovery escape is absent. There is time to make a correct decision on what action to take if a fall occurs while wearing a full
body harness. It is important to remember “DO NOT PANIC.” Remain calm and implement your practiced rescue, relief and recovery plan.
NEVER allow the tether strap to get under your chin or around our neck. The length of the harness tether MUST be minimized at all times. It should be adjusted
so that it is above the head with no slack (snug) in the sitting position and you should have the minimum amount of slack possible when climbing.
W A R N I N G
DO NOT use this ladderstand under the influence of alcohol,
drugs, or medication. Using ladderstand under the influence
of alcohol, drugs, or medication may result in serious injury or
death.
NEVER use ladderstand if you have dizzy spells, a heart
problem, are afraid of heights, have been advised by a doctor
or other health care provider not to climb, or have any
condition that would impair your ability to climb up or down or
use treestand as it could result in serious injury or death.
NEVER remove or deface ladderstand warning labels.
Replacement labels can be obtained from the address below.
NEVER make any alterations or modifications to the ladder
stand.Doing so may result in serious injury or death and will
void all warranties.
NEVER stand on treestand seat or armrests. Standing on any
of these parts may cause the treestand to break or fail resulting
in serious injury or death.
NEVER use treestand in a tree that is dead, diseased, leaning,
or on wet or uneven ground as the tree may fall, break, or
uproot and may result in serious injury or death.
NEVER use ladderstand during inclement weather. DO NOT
use treestand during thunderstorms or any other weather
conditions including (but not limited to) lightning, freezing rain,
high wind that could create slippery or dangerous conditions.
DO NOT use this ladderstand without reading and following all
warnings and instructions before each use. Failure to do so
may result in serious injury or death.
DO NOT exceed the ladderstand's 300 lbs. weight limit, which
includes your body weight as well as the weight of your clothes
and gear. Exceeding the ladderstand's weight limit may cause
the treestand to break or fail resulting in serious injury or death.
ALWAYS wear a Full Body Harness while using this ladder
stand. Failure to wear a full body harness while using
this ladderstand may result in serious injury or death.
ALWAYS inspect your ladderstand before each use. DO NOT
use if parts are missing, worn, or damaged.
SAMPLE
©2012 (rev. 12/11)
www.treestandcustomerservice.com

Customer Service Department 1-866-972-6168
• ALWAYS thoroughly inspect the tree before installing your product. DO NOT install your TREE/LADDER STAND onto any dead or unsafe tree, telephone or utility
pole, structural column, or man-made structure. Doing so may result in serious injury or death.
• ALWAYS select the proper tree for use with your TREE/LADDER STAND. Select a live straight tree that fits within size limits recommended (minimum tree
diameter must be no less than 9 inches and maximum of 18 inches.). DO NOT rely on a branch for support.
• DO NOT select a tree in the dark or choose a tree in close proximity to a fence. You must not have any stumps or rocks beneath your tree.
• NEVER use TREE/LADDER STAND on a tree that is dead, diseased , leaning or on wet and uneven ground as the tree may fall, break or uproot.
• Your tree must not be wet, icy or slippery or on wet, swampy, or loose ground that allows the tree to be unstable. Check the ground under TREE/LADDER STAND
to ensure it is firm and level.
• Be sure you have a level stand platform. Your tree must not lean or have any irregular shape.
• Tree must not have any loose or scaly bark or excessive vines, nails, screws, or any other sharp objects protruding that may sever webbing on product. Any
surrounding trees must not lean or have dead limbs that may fall onto you or your product.
• NEVER HURRY!! HURRYING CAUSES ACCIDENTS!! While climbing a TREE/LADDER STAND, make slow, even movements no more that ten to twelve inches
at a time. Make sure you have proper contact with tree and/or TREE/LADDER STAND every time you move. On ladder tree stand, ALWAYS maintain three points
of contact with each step and ALWAYS lean forward as you climb.
Several treestands are equipped with a footrest, armrests and/or shooting rail. Neither the footrest, armrests nor the shooting rail have been designed to
support a user’s weight. Under NO circumstances should you place more than fifteen (15) pounds of weight on these structures. Doing so will put the user
in serious risk of injury or death.
CHOOSING A SAFE TREE
PROPER CARE AND MAINTENANCE:
• Inspect for defects (damage, rot, corrosion, cracks, freezing, excessive heat, etc.) before every use is required. Do not use if damage is detected or
suspected.
• We recommend replacing all hardware/cables/nuts/bolts/clips on your tree stand every two (2) years or sooner if inspection finds it necessary. Use only
Primal Vantage approved replacement straps and parts. Use of any other straps or parts, will be viewed as a modification to the product. Any modification
will void the warranties and relieve Primal Vantage from all liabilities. Failure to follow these instructions may result in serious injury or death.
• By registering your product, you may be enrolled in our discount program.
You may receive a 20% off coupon for our website store, www.primal-store.com to purchase replacement parts in the future.
• DO NOT overtighten the hardware. DO NOT use a socket wrench. This can lead to structural damage and may negatively affect the performance of your
stand. Failure to follow these instructions may result in serious injury or death.
©2012 (rev. 12/11)
www.treestandcustomerservice.com

Platform Parts List
Customer Service Department 1-866-972-6168 www.treestandcustomerservice.com
Left Platform (1)
A
Right Platform (1)
B
Seat
Pedestal (1)
C
Seat Back (1)
D
Seat Platform
(1)
E
Shooting Rail
(2)
F
Armrest (2)
GHandle Rail
(2)
H
Rear Leg Brace (2)
J
Support Brace (4)
Shooting Rail Support (4)
P
J
K
P
N
M
Q
L
Part # WLP-600
Part # WRP-600
Part # WSP-600
Part # WSB-600
Part # WSP-610
Part # WSR-600
Part # WAR-600
Part # WHR-600
Part # WRLB-600
Part # WSRB-600
Part # WSC-611
Part # WSC-610
Part # WS-650
Part # WARC-600
B
A
1 Seat Pedestal
C
D
E
F
G
H
1 Left Platform
1 Right Platform
1 Seat Back
2 Shooting Rail
2 Armrest
2 Rear Leg Brace
4 Support Brace
2 Handle Rail
1 Seat Platform
1 Seat Back Cushion
1 Seat Cushion
1 Skirt
2 Armrest Cover
4 Shooting Rail Cover Part # WSRC-600
O
Part # WSRS-600
4 Shooting Rail Support
M12x75mm M12x65mm
M12x55mm
M12x110mm
M12x30mm RED Bolt
with Large Washer
Platform Hardware Blister Pack
Platform Hardware
4 M12x65mm Bolt
24 M12x55mm Bolt
Part # 1265
Part # 1255
65
55
110 2 M12x110mm Bolt Part # 12110
4 M12x75mm Bolt Part # 1275
75
K
Seat Cushion
(1)
M
Seat Back
Cushion (1)
N
Shooting Rail Cover (4)
O
Skirt (1)
Q
Armrest
Cover (2)
L
©2012 (rev. 10/11)
Tools Required
Adjustable Wrench
MODEL: WMTS-15R
15 FT. TRIPOD
• Weight Limit 300 lbs.
• Do Not Over Tighten Fasteners
Distributed by Tahsin Industrial Corp. USA 685 Route 10 East, Randolph, NJ 07869

Customer Service Department 1-866-972-6168 www.treestandcustomerservice.com
Leg Foot (2)
Upper Leg (2)
Lower Leg (2)
Male Brace (6)
Leg and Ladder Parts List
X
R
T
V
U
W
Y
S
Part # WLF-650
Part # WL-600
Part # WL-610
Part # WB-600
Part # WBL-600
Part # WTL-600
Part # WCB-600
Part # WAP-600
2 Leg Foot
2 Upper Leg
2 Lower Leg
4 Anchor Pin
6 Male Brace
1 Bottom Ladder
1 Top Ladder
3 Cross Brace
Bottom Ladder
Section (1)
Top Ladder
Section (1)
Cross Brace (3)
Anchor Pin (4)
Leg and Ladder Hardware
22 M12x40mm Bolt Part # 1240
8 M12x45mm Bolt Part # 1245
8 M10x30mm Bolt Part # 1030
45
40
30
R
S
T
VU
WX
Y
©2012 (rev. 10/11)
Tools Required
Adjustable Wrench
MODEL: WMTS-15R
15 FT. TRIPOD
• Weight Limit 300 lbs.
• Do Not Over Tighten Fasteners
Distributed by Tahsin Industrial Corp. USA 685 Route 10 East, Randolph, NJ 07869
Leg and Ladder Hardware Blister Pack
M12x45mm
M10x30mm
M12x40mm

Distributed by Tahsin Industrial Corp USA, 685 Route 10 East, Randolph, NJ 07869
Customer Service Department 1-866-972-6168 www.treestandcustomerservice.com
ASSEMBLY INSTRUCTIONS PAGE 1 MODEL: WMTS-15R
15FT. TRIPOD
3. Slide both halves of Shooting Rail F together and secure with
1-M10x30mm bolt on each side. Set aside for future use.
AB
40
110
40
1. Slide Left Platform A into Right Platform B . Use 1-M12x40mm
bolt on each side of platform. Use 2-M12x110mm bolt in the middle
of the platform. Set aside for future use.
E
D
G
55
55
2. Attach Seat Back D to Seat Platform E using 1-M12x55mm
Bolt on each side.
Attach Armrest G to Seat Back D and Seat Platform E using
2-M12x55mm Bolt at each connection point.
Set aside for future use.
F
F
30 30
W
T
30
4. Insert the crimped end of Male Brace T into the end of Cross
Brace W near the pivot point. Insert 1-M10x30mm Bolt at each
point. Do this for ALL remaing Cross Braces.
Set aside for future use.
©2012 (rev. 10/11)

Distributed by Tahsin Industrial Corp USA, 685 Route 10 East, Randolph, NJ 07869
Customer Service Department 1-866-972-6168 www.treestandcustomerservice.com
ASSEMBLY INSTRUCTIONS PAGE 2 MODEL: WMTS-15R
15FT. TRIPOD
5. Turn the assembled platform over so that
the top of the platform is on the ground.
Attach Handle Rail H to the bottom of the
assembled platform using 2-M12x65mm Bolts
for each Handle Rail.
A
B65
H
H
6. With the platform still upside down, Attach
Rear Leg Brace J to the rear of the platform using
2-M12x75mm Bolts for each Rear Leg Brace.
A
B
JJ
75 75
7. Turn the platform upright.
Attach Seat Pedestal C to the center of the platform
using 4-M12x45mm Bolts.
BA
C
45
8. Disassemble the RED Bolt with Large Washer.
Place the Large Washer on top of the Seat Pedestal C . Hold
the assembled Seat on the Seat Pedestal. Place a metal
washer onto the RED bolt, then insert a nylon washer on the
bolt. Insert the bolt through the Seat Platform, Large Washer,
and the seat Pedestal. Place another nylonwasher onto the
bolt, then the last metal washer and tighten with the nut.
RED BOLT
CE
©2012 (rev. 10/11)

Distributed by Tahsin Industrial Corp USA, 685 Route 10 East, Randolph, NJ 07869
Customer Service Department 1-866-972-6168 www.treestandcustomerservice.com
ASSEMBLY INSTRUCTIONS PAGE 3 MODEL: WMTS-15R
15FT. TRIPOD
P
P
K
KP
K
P
K
55 55
40
40
40
40
P
P
KK
55 40
40 40
40 55
REAR CLOSEUP
FRONT CLOSEUP
9. Attach Shooting Rail Support P the assembled platform using 1-M12x55mm Bolt for each piece.
(See Close-up for correct placement).
Attach Support Brace K to the assembled platform and to the INSIDE of the Shooting Rail Supports using 1-M12x40mm Bolt for
each connection point. (See Close-Up for correct placement).
55
55 55
55
P
F
F
P
P
P
10. Attach assembled Shooting Rail F to each
Shooting Rail Support P using 1-M12x55mm
Bolt at each connection point.
©2012 (rev. 10/11)

Distributed by Tahsin Industrial Corp USA, 685 Route 10 East, Randolph, NJ 07869
Customer Service Department 1-866-972-6168 www.treestandcustomerservice.com
ASSEMBLY INSTRUCTIONS PAGE 4 MODEL: WMTS-15R
15FT. TRIPOD
N
M
L
O
Q
11. Attach each Shooting Rail Cover O to Shooting Rail F .
Attach Each Armrest Cover L to each Armrest G .
Attach Seat Back Cushion N to Seat Back D .
Attach Seat Cushion M to Seat Platform E .
12. Tie Skirt Qaround the top of Shooting Rail and the Platform.
©2012 (rev. 10/11)

Distributed by Tahsin Industrial Corp USA, 685 Route 10 East, Randolph, NJ 07869
Customer Service Department 1-866-972-6168 www.treestandcustomerservice.com
ASSEMBLY INSTRUCTIONS PAGE 5 MODEL: WMTS-15R
15FT. TRIPOD
13. Insert Upper Leg R into Rear Leg Brace J .
(The Upper Leg has 2 holes on the Bottom). The brackets
on the legs MUST be facing towards the inside of the stand.
Secure with 2-M12x55mm Bolts on each leg.
RR
JJ
55
R
S
R
S
55 55
14. Insert Lower Leg S into Upper Leg R .
(The Lower Leg has 1 hole on the Bottom). The brackets
on the legs MUST be facing towards the inside of the stand.
Secure with 2-M12x55mm Bolts on each leg.
55
©2012 (rev. 10/11)

Distributed by Tahsin Industrial Corp USA, 685 Route 10 East, Randolph, NJ 07869
Customer Service Department 1-866-972-6168 www.treestandcustomerservice.com
ASSEMBLY INSTRUCTIONS PAGE 6 MODEL: WMTS-15R
15FT. TRIPOD
45
U
45
H
45
V
45
U
16. Insert Top Ladder Section U into Handle Rails H .
The brackets on the Ladder Section MUST be facing
towards the inside of the stand.
Secure using 1-M12x45mm Bolt on each side.
17. Insert Bottom Ladder Section V into Top Ladder
Section U . The brackets on the Ladder Section
MUST be facing towards the inside of the stand.
Secure using 1-M12x45mm Bolt on each side.
40
R
S
R
S
40
40
40
W
©2012 (rev. 10/11)
15. Attach one Cross Brace W to the Upper Leg R and
Lower Legs S using 1-M12x40mm Bolt at each point.
Attach Braces to the OUTSIDE of the Brackets

Distributed by Tahsin Industrial Corp USA, 685 Route 10 East, Randolph, NJ 07869
Customer Service Department 1-866-972-6168 www.treestandcustomerservice.com
ASSEMBLY INSTRUCTIONS PAGE 7 MODEL: WMTS-15R
15FT. TRIPOD
VS
R
R
S
40
40
40
U
40
W
V
R
S
40
40
U
40
40
W
LEG BRACKET
CLOSEUP
X
55
S20. Insert Foot X into Lower Leg S .
The Foot is adjustable so you can raise or
lower the stand as needed.
Insert 1-M12x55mm Bolt to secure.
Insert Anchor Pin Y through the hole on
each Foot X when the stand is in desired
position.
©2012 (rev. 10/11)
18. Attach another Cross Brace W to Top Ladder Section U and
Lower Leg S . Attach the same Cross Brace to Bottom Ladder
Section V and Upper Leg R using 1-M12x40mm Bolt at each
point. Attach Braces to the OUTSIDE of the Brackets.
19. Attach the last Cross Brace W to Top Ladder Section U and
Lower Leg S . Attach the same Cross Brace to Bottom Ladder
Section V and Upper Leg R using 1-M12x40mm Bolt at each
point. Attach Braces to the OUTSIDE of the Brackets.
W
Table of contents
Popular Sport & Outdoor manuals by other brands

Lifetime
Lifetime 73621 Assembly instructions and owner's manual

BAT
BAT LOGIC BasePlates Fitment Guide

Bestway
Bestway Supersized Duck Rider manual

PURE
PURE P4F940150 Instructions for use

SPORTSPOWER
SPORTSPOWER 6VL33 Assembly instruction

SMARTPONG
SMARTPONG Table Tennis Robot INSTALLATION AND TROUBLESHOOTING BRIEF INSTRUCTION GUIDE

Rukket Sports
Rukket Sports GLOW Assembly instructions

Bison
Bison DIRECT BURY SQUARE BASKETBALL installation instructions

Pop-A-Shot
Pop-A-Shot OUTDOOR DUAL SHOT PASOUT22 Assembly instructions

CAP
CAP FM-FLDIPR Assembly instructions

Kwik Tek
Kwik Tek Sportsstuff manual

Gato Sports
Gato Sports LED USB SPORT VEST user manual