TRENT PM-1P-10-5ic User manual
PM-ic the Intelligent answer
Model: PM-1P-10-5ic
REF: PM-OPM3 0.01 issue - 3 05-11
PM-ic Power Monitors
GAS SUPPLY CONTROL STATION
with
Fan Power Ventilation Inter-lock
For Models: PM-1P-10-5ic
OPERATOR’S MANUAL
PM-ic the Intelligent answer
Model: PM-1P-10-5ic
REF: PM-OPM3 0.01 issue - 3 05-11
Product Overview
The PM-ic Fan power monitor unit is part of a range of products and ancillary equipment designed to meet the ever changing
requirements of the catering industry and associated regulations.
The system comes in a number of models for you to select which are based on our patented system.
PM-ic Power Monitor Five channel unit with over & under current monitoring
The controller has been designed to make for easy system usage.
Contents
1.01 How does my PM-ic unit work?
1.02 How do I start my PM-ic unit?
1.03 How do I stop my PM-ic unit?
1.04 What do I do if my PM-ic unit does not operate?
1.05 Do I have any form of override?
1.06 Fault finding
1.01 How does my PM-ic unit work?
Your PM-ic unit is designed to ensure that your kitchen ventilation system is operational and maintaining the design air flow rates
before your gas supply is enabled to your cooking appliances.
The PM-ic unit is operated via an easy wipe clean facia with clear high bright LED indicator arrangement.
1.02 How do I start my PM-ic unit?
First start your kitchen canopy ventilation system.
Turn the system set/reset key switch to the "set" position and release and the PM-ic unit will carry out a number of system
checks. If all checks are clear the “gas valve output” LED will switch on and open the gas supply to your cooking appliances.
1.03 How do I stop my PM-ic unit?
Switch off your kitchen canopy ventilation system and the “gas valve output” LED will switch off and the gas valve will close,
isolating the gas supply to your appliances.
NOTE: Always ensure that all appliances have been switched off and taps closed.
1.04 What do I do if my PM-ic unit does not operate?
If after the system set/reset key switch has been turned your gas valve output light does not come on, the gas valve fails to
open’ check the following :
1 Ensure that your kitchen canopy ventilation system is operational.
2 If not have your supply to the unit checked by an electrician.
3 Ensure you have power to the unit; is the power on lamp lit?
4 Check that the SYSTEM STOP button on the front of the panels has not been pressed.
5 Check that either the fire alarm or remote knock-off push buttons have not been activated, if fitted.
If the steps above do not solve your problem, refer to section 1.06 of this manual for further instructions.
PM-ic the Intelligent answer
Model: PM-1P-10-5ic
REF: PM-OPM3 0.01 issue - 3 05-11
1.05 Do I have any form of override?
The PM-ic unit has no means of system override.
ANY FORM OF OVERRIDE IS NOT PERMITTED UNDER THE CURRENT REGULATIONS
1.06 Fault finding
In the event that your PM-ic unit is not operational, the following has been designed to help you identify your problem and offer a
course of action for you to take.
Fault finding Only to be carried out by a qualified engineer
Fault
Possible cause
Action
No Power On LED a. No power to the unit Check power supply to unit,
mains cables, terminals and
5Amp MCB switch on the side of
the unit.
b. Primary transformer fuse “blown” Remove cover and check if
“blown”. If yes, check for any
signs of a wiring fault and rectify
before replacing with a new fuse.
c. None of the above Call for further assistance
Gas valve output lamp
is not lit and gas valve
is closed
a. Fans are not running Check that the fans are running
correctly
b. Fans are running but unit not set correctly Check that the respective
channel lamps are on. Action as
detailed in set-up instructions
c. User definable input operated Check if remote knock-off and
fire alarm inputs and any other
remote circuits have been
activated
d. Emergency Gas Shut off push button on
the front of the unit has been pressed
Twist and reset
Gas valve output lamp
is on and gas valve is
closed
a. No power to gas valve Check in / out terminals to see if
240Vac is present and check
cables to gas valve.
b. Gas valve not operational Check if 240Vac is present at
gas valve terminals. If yes
replace gas valve.
Gas valve open but no
gas at appliance
a. Gas supply has been isolated or is
blocked
Check gas supply
b. No gas pressure Check gas supply
Channel lamp not on a. Fans are not running Check that the fans are running
correctly
b. Fans are running but unit not set correctly Check that the respective
channel lamps are on. Action as
detailed in set-up instructions
PM-ic the Intelligent answer
Model: PM-1P-10-5ic
REF: PM-OPM3 0.01 issue - 3 05-11
FOR FURTHER TECHNICAL ASSISTANCE, PLEASE CONTACT US BY
Phone: 01782 844688
Fax: 01782 844772
E-mail: info@trentproducts.com
Web site: www.trentproducts.com
Note: i) Ensure that the electrical installation has been installed in
accordance with the current edition of the IEE regulations.
ii) Ensure that the gas installation has been installed in accordance with the current gas
regulations and GAS SAFE guide-lines.
iii) Ensure that the ventilation and extract system has been set to the correct air flow
design levels in accordance with the current regulations.
iv) If in doubt, ask! (Contact us on or by any of the above).
v) Ensure that the client has been shown how to operate the system and that they have
been handed the Operators Manual.
This symbol on this product or the package indicates that disposal of this product
After its lifecycle could harm the environment.
DO NOT dispose of this product (or batteries if used) as unsorted municipal waste.
It should be disposed by a specialised company for recycling.
This product should be returned to your distributor or to a local recycling service.
Respect the local environment rules.
TRENT PRODUCTS
Trent House
Dewsbury Road
Fenton
Stoke-on-Trent
Tel: 01782 844688 Fax: 01782 844772
Web: www.trentproducts.com
E-mail: info@trentproducts.com
