Trenton TMM4500 User manual

TMM4500
4U 4-PANEL RACKMOUNT
LCD MONITOR
No. TMM4500-xxx Revision A
REFERENCE GUIDE
Publication No. 8404500-04044

WARRANTY
The following is an abbreviated version of Trenton Systems’ warranty policy for rackmount computer
products. For a complete warranty statement, contact Trenton or visit our website at
http://www.trentonsystems.com/.
All boards used in systems delivered by Trenton; including rackmount LCD monitors, are covered under a
pass-through warranty. For example, if Trenton PICMG 1.3 boards are used in the system then these boards
will carry a five-year warranty. All other system sub-components including but not limited to power
supplies, LCD displays, DVDs, CD-ROMS, etc. are covered under their original manufacturer’s warranty.
All systems built by Trenton are warranted against defects in material, workmanship and design for a
period of one year from date of delivery. Repair or replacement products will be warranted for a period of
three months from the date of shipment or for the remainder of the original warranty period for that
particular product, whichever is longer. Any software or firmware that is delivered by Trenton will be
warranted for a period of one year to perform in accordance with published specifications prepared,
approved and issued by Trenton and/or the appropriate 3rd party vendor. Contact Trenton for the complete
system warranty policy.
Buyer agrees that if a Trenton product proves defective, Trenton is only obligated to repair, replace or
refund the purchase price of this product at Trenton's discretion. The warranty is void if the product has
been subjected to alteration, neglect, misuse, or abuse; if any repairs have been attempted by anyone other
than Trenton; or if failure is caused by accident, acts of God, or other causes beyond the control of Trenton.
Trenton reserves the right to make changes or improvements in any product without incurring any
obligation to similarly alter products previously purchased.
In no event shall Trenton Systems, Inc. be liable for any defect in hardware or software or loss or
inadequacy of data of any kind, or for any direct, indirect, incidental or consequential damages arising out
of or in connection with the performance or use of the product or information provided. Trenton Systems,
Inc.’s liability shall in no event exceed the purchase price of the product purchased hereunder. The
foregoing limitation of liability shall be equally applicable to any service provided by Trenton Systems,
Inc.
RETURN POLICY
Products returned for repair must be accompanied by a Return Material Authorization (RMA) number,
obtained from Trenton Systems prior to return. Freight on all returned items must be prepaid by the
customer, and the customer is responsible for any loss or damage caused by common carrier in
transit. Items will be returned from Trenton Systems via Ground, unless prior arrangements are made by
the customer for an alternative shipping method
To obtain an RMA number, call us at [phone] or [phone]. We will need the following
information:
Return company address and contact
Model name
Serial number from chassis label
Description of the failure
An RMA number will be issued. Mark the RMA number clearly on the outside of each box, include a
failure report for each item and return the product(s) to our Gainesville, GA facility:
TRENTON Systems, Inc.
2350 Centennial Drive
Gainesville, GA 30504
Attn: Repair Department
Contact Trenton for our complete service and repair policy.

TRADEMARKS
Trenton and Trenton Systems are trademarks or registered trademarks
of TRENTON Systems, Inc.
IBM, PC/AT, VGA, EGA, OS/2 and PS/2 are trademarks or registered trademarks
of International Business Machines Corp.
Intel is a registered trademark of Intel Corporation.
PICMG is a registered trademark of the PCI Industrial Computer Manufacturers Group
MS-DOS and Microsoft are registered trademarks of Microsoft Corp.
All other brand and product names may be trademarks or registered trademarks
of their respective companies.
LIABILITY DISCLAIMERS
In no event will Trenton Systems be responsible or liable for indirect or consequential damages resulting
from the use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the
many system variables and application requirements associated with any particular installation, Trenton
Systems cannot assume responsibility or liability for actual system use based on the examples and
diagrams. No patent liability is assumed by Trenton Systems with respect to the use of the information,
components, equipment or software described in this manual. This manual is as complete and factual as
possible at the time of publication; however, the information in this manual may have been updated since
that time. Trenton Systems, Inc. reserves the right to change the functions, features or specifications of
their products at any time, without notice.
Reproduction of the contents of this manual, in whole or part, without written permission of Trenton
Systems is prohibited.
Copyright ©2014 by Trenton Systems, Inc. All rights reserved.
E-mail: [e-mail]
Web: www.TrentonSystems.com
TRENTON Systems, Inc.
2350 Centennial Drive • Gainesville, Georgia 30504
Sales: [phone] • Phone: [phone] • Fax: [phone]

TMM4500 Reference Guide
Table of Contents
ADVISORY & SAFETY CONVENTIONS I
SAFETY INSTRUCTIONS I
INSTALLATION PRECAUTIONS II
RACK MOUNTING PRECAUTIONS (WHERE
APPLICABLE) III
SERVICE AND REPAIR PRECAUTIONS III
SAFETY STANDARDS III
CHAPTER 1 - SYSTEM OVERVIEW 1-1
DESCRIPTION 1-1
BASE FEATURES 1-1
DISPLAY 1-1
LCD CONTROLLER 1-1
POWER 1-1
ADDITIONAL SPECIFICATIONS 1-1
PACKING LIST 1-1
CHAPTER 2 - MECHANICAL OVERVIEW 2-1
TMM4500 LAYOUT DIMENSIONS AND OPTIONAL
CONFIGURATIONS 2-1
CHAPTER 3 - INSTALLATION INSTRUCTIONS 3-1
BEFORE YOU BEGIN 3-1
RACK MOUNTING 3-1
RACKMOUNT INSTRUCTIONS 3-1
CHAPTER 4 - TMM4500 OPERATION 4-1
CONNECTING THE TMM4500 DISPLAYS 4-1
BACK PANEL LAYOUT AND CONNECTING TMM4500
POWER 4-1
DEPLOYING THE TMM4500 –BASIC DISPLAY DRAWER
OPERATION 4-2
4-2
4-2
4-2
DEPLOYING THE TMM4500 –SETTING UP THE DISPLAY
HEAD MODULE STOP 4-3
4-3
CHAPTER 5 - UNIFIED BUTTON BOARD
OPERATION 5-1
OSD BUTTON BOARD LAYOUT 5-1
OSD INDICATOR LIGHT DEFINITIONS 5-1
CHAPTER 6 - MAINTENANCE AND
TROUBLESHOOTING 6-1
MAINTAINING THE TMM4500 6-1
TROUBLESHOOTING THE TMM4500 6-1
TROUBLESHOOTING THE TMM4500 (CONTINUED) 6-2
CHAPTER 7 - TMM4500 SPECIFICATIONS 7-1
ENVIRONMENTAL 7-1
ELECTRICAL 7-1
PHYSICAL 7-1
DISPLAYS 7-1
SAFETY STANDARDS 7-1
Trenton Systems, Inc.

TMM4500 Reference Guide
Advisory &Safety Conventions
Follow all instructions marked on the product and described in this document. Pay close attention to the three
types of advisories used throughout this manual: Notes, Cautions, and Warnings. They provide helpful
information or alert you to the potential for hardware damage or personal injury. The following is an example
of each type of advisory. Use caution when servicing any electrical component.
NOTE:A Note indicates information that will help you make better use of the rackmount LCD.
CAUTION
A CAUTION indicates potential damage to hardware and tells you
how to avoid the problem.
WARNING
A WARNING indicates the potential for bodily harm and tells you
how to avoid the problem.
SAFETY INSTRUCTIONS
Before handling the product, read the following instructions and safety guidelines to prevent damage to the
product and to ensure your own personal safety. Refer to the “Advisories” section for advisory conventions
used in this manual, including the distinction between Warnings, Cautions, and Notes.
Do not remove any of the covers. Only qualified, experienced, authorized electronics service personnel
should access the interior of the product. The power supplies produce high voltages and energy hazards,
which can cause bodily harm.
Do not use the product near water. Do not place any liquids (even a wet or damp cloth) on or near the
product. Liquids create an electrical hazard. Do not expose the Product to rain or moisture.
WARNING
To avoid the risk of severe electric shock, do not remove the cover
or back of the monitor. There are no user serviceable parts inside.
Refer all servicing to Technical Support.
i Trenton Systems, Inc.

TMM4500 Reference Guide
Installation Precautions
WARNING: This system has internal components which may be damaged by electrostatic discharge.
To protect yourself from harm and the internal components from electrostatic damage, be sure to observe the
following precautions when handling or storing the system:
• When you disconnect the power cable from the socket, pull on the plug not the cord.
• To help prevent electric shock, connect the power cable to a properly wired and grounded
power source. Do not use adapter plugs or remove the grounding prong from the cable.
• Always connect any equipment used with the product to properly wired and grounded
power sources. Be sure to tighten all connector screws.
• Reliable earthing of this equipment must be maintained. Particular attention should
be given to supply connections when connecting to power strips, rather than direct
connections to the branch circuit.
• Do not connect or disconnect this product during an electrical storm.
• Do not place any object on the cables that might cause the cables to make sharp bends or that
affect the integrity of the cables. Be sure that cables are not located where they can be
stepped on or tripped over.
• Route all wiring and cabling away from heat sources and sharp metal edges to avoid
damage.
• Keep product away from direct sunlight and heat sources. Hot air may cause damage to
the cabinet and other parts.
• Install the product in a well-ventilated area. Do not block ventilation slots and openings
with objects.
• Do not allow metal pieces or objects of any kind to fall into the ventilation holes. Keep the
ventilation holes and openings clean. Vacuum openings if you notice dirt accumulating on
them.
• Handle the product with care. The display may contain glass parts. Dropping the product
may cause any glass parts to break.
• To help protect the product from sudden, transient increases and decreases in electrical
power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS).
• Consideration should be given to the connection of the equipment to the supply circuit and the
effect that circuit overloading might have on overcurrent protection and supply wiring.
Appropriate consideration of equipment nameplate ratings should be used when addressing
this concern.
• The ambient temperature within the rack may be greater than room ambient. Installation
should be such that the amount of air flow required for safe operation is not compromised.
Consideration should be given to the maximum rated ambient.
• Installation should be such that a hazardous stability condition is not achieved due to
uneven loading.
Trenton Systems, Inc. ii

TMM4500 Reference Guide
Rack Mounting Precautions (WhereApplicable)
The following safety guidelines are provided for all rack-mountable equipment:
•Maximum operating ambient temperature is typically 50 °C.
•Never restrict the airflow through the devices’ fan or vents.
•When installing equipment into a rack, distribute the units evenly.
•Otherwise, hazardous conditions may be created by an uneven weight distribution.
•Connect the unit only to a properly rated supply circuit.
•Reliable earthing (grounding) of rack-mounted equipment should be maintained.
Service and Repair Precautions
Unplug the product from the power outlet and refer servicing to qualified service personnel in the event that:
•Liquid is spilled in to the product or the product is exposed to rain or water.
•The product does not operate properly when the operating instructions are followed.
•The product has been dropped or the frame has been damaged.
•The product exhibits a distinct change in performance, indicating a need for service.
•The power cable or plug is damaged or frayed.
Safety Standards
Unplug the product from the power outlet and refer servicing to qualified service personnel in the event that:
•Liquid is spilled in to the product or the product is exposed to rain or water.
•The product does not operate properly when the operating instructions are followed.
•The product has been dropped or the frame has been damaged.
•The product exhibits a distinct change in performance, indicating a need for service.
iii Trenton Systems, Inc.

TMM4500 Reference Guide
Chapter 1 -System Overview
DESCRIPTION
The TMM4500 represents the first of its kind multi-head rackmount LCD monitor platform. Within a
standard 19” component rack the TMM4500 “Hydra” display head design can accommodate from one to four
21.5” LCD displays.
BASE FEATURES
• 3U/4U 26” Deep 19” Rack Mount
• Rugged All Aluminum Design
• 1,2 or 3 Screens Available in 3U, Quad in 4U Only
• Unified Button Board Design (Patent Pending) - For Independent or Simultaneous LCD Control
• Heavy Duty Friction Slides
• Integrated Cable Guide
• Gas Spring Support Struts
• Innovative Front Face w/ Locking Display Module Stop
• Robust Torque Hinges
• 90 Degree Mechanical Swivel
• XLR Quick-Disconnect Power Cord
DISPLAY
• 21.5” widescreen Full HD 1920×1080, (1080p) with LED backlight
• 250NITS brightness
• Ultra wide viewing angle 178/178
• 16.7M colors
• 1000:1 contrast ratio
• Response time 8ms G to G Latest
LCD CONTROLLER
• Support for digital picture-in-picture
• Standard video inputs include: VGA, DVI, CVS(2x), YPbPr, and HDMI
• Optional video input interfaces include: Dual or single channel 3G HD/SD-SDI
POWER
• +12VDC operation via a universal 100-240VAC adapter
• The input power connector is a secure XLR quick disconnect
• 175W power supply
ADDITIONAL SPECIFICATIONS
• Operating Temperature: 0-50c
• Storage Temperature: 20-60c
• Standard 4-Screen System Dimensions: 7”H (4U )x 19”W x 26”D
• Optional Single/Dual/Triple System Dimensions: 5.25”H (3U)x19”Wx26”D
• Standard 4-Screen System Weight: 85 lbs. (Approx.)
• Optional Single-Screen System Weight: 50 lbs. (Approx.)
• Optional Dual-Screen System Weight: 61 lbs. (Approx.)
• Optional Triple-Screen System Weight: 70 lbs. (Approx.)
PACKING LIST
The standard Trenton TMM4500 is shipped with the following:
• Universal 100-200VAC, 175W power supply and a cable with a XLR quick disconnect cable
• One or two, 10ft. (3.1m) AC power cord(s)
• Four (4) video interface cables (interface type depends on what was ordered from Trenton)
• Friction slides (installed)
• Ship kit containing standard rackmount hardware
1-1 Trenton Systems, Inc.

TMM4500 Reference Guide
A. 1,2, or 3 Screens Available in a 3U; Quad Available in 4U Only
B. New Unified Button Board Design for Independent or Simultaneous LCD Control
C. Front Face - Innovative folding front face which acts as a display module stop
D. Solid Bearing Slides - 2 Sets of heavy duty steel solid bearing/friction slides
E. Cage-Style Cable Guides - To protect and secure cabling for continuous use
F. Electronics Back - Large area for easy connections and access to electronics
G. Display Module Lock Downs - To ensure the panel is secure during transport
H. Telescoping Arms w/ “L” Brackets - This technology facilitates easy straight-in mounting
(Actual arms/brackets not shown)
I. Assembly Cover - (Comes with 4U only, not shown)
Trenton Systems, Inc. 1-2

TMM4500 Reference Guide
Chapter 2 -MechanicalOverview
TMM4500 LAYOUT DIMENSIONS AND OPTIONAL CONFIGURATIONS
2-1 Trenton Systems, Inc.

TMM4500 Reference Guide
Chapter 3 -Installation Instructions
BEFORE YOU BEGIN
We suggest you power the unit up and confirm it functions correctly and that nothing was
damaged in shipping.
We suggest you power the unit up and confirm it functions correctly and that nothing was
damaged in shipping.
CAUTION
Do not remove the cover or back of your new equipment. There are
no user serviceable parts inside. Contact Trenton Systems technical
support if you need assistance.
RACK MOUNTING
The TRC4012 system can be installed in a rackmount cabinet that conforms to EIA standards for computer
equipment with 19-inch wide panels. The cabinet must be tall enough to accommodate the computer’s
height and deep enough to accommodate the system’s depth, while providing the proper clearances for air
flow and cabling. A cabinet with a standard depth of 31.5 inches (800mm) should be sufficient; however, a
rack with a non-standard depth dimension of at least 22 inches (559mm) will provide the suggested
minimum front and rear chassis clearances needed for an installation.
The TRC4012 is designed to be supported in the cabinet with rack slides or placed on a cabinet shelf. The
front flanges of the computer are designed to secure the TRC4012 to the rack cabinet’s front mounting rails
RACKMOUNT INSTRUCTIONS
A) Determine the mounting location within the rack and mark the mounting holes in the front and
rear of the rack enclosure accordingly (this is for easy reference while you are mounting the equipment).
NOTE If installing by yourself or even with a helper, just below where you are going to mount the unit
install 2 of the 10-32 screws (or M6 if using an alternate rack) in the front mounting surface leaving at
least 1/4” inch of thread exposed. This will act as a wrest to assist holding the unit in place when
installing the unit.
B) Install the rear “L” mounting brackets to the rear face of the enclosure using 4x 10-32 Panhead
Screws set at the desired height/location.
C) Find the target installation depth by measuring the front face/mounting surface of the rack to
center- line of the mounting hole of the rear “L” mounting bracket.
D) The measurement from the front ear to the rear arms elongated mounting holes must be the same
length as step 3. Some adjustment of the aluminum support arms is likely needed ensure a proper fit. To
adjust the arms use the Hex Head tool to loosen or remove the Pancake screws as necessary until the
elongated holes of the arms match the measurement. Once at the correct measurement then once again
secure the arms in place.
3-1 Trenton Systems, Inc.

TMM4500 Reference Guide
NOTE: The arm may need to be adjusted to the next set of mounting holes to fit correctly.
E) Slide the rack mount unit straight into the rack (if following the TIP you can wrest it on the screws
you previously installed in the front) and secure the rear arms into the “L” brackets with the provided 10-32
Panhead screws.
F) With the remaining 10-32 screws, secure the unit into the Rack Frame. (Removing the 2x 10-32
screws you were using as stops in the TIP and install them into the remaining hold of the rack ears). Ensure
the unit is level and then tighten all of the 10-32 screws.
G) Your equipment should now be mounted in the rack.
NOTE: This is a general install guide. Actual rack mount install may vary from unit to unit. For
additional assistance please contact Trenton Systems technical support.
Trenton Systems, Inc. 3-2

TMM4500 Reference Guide
Chapter 4 -TMM4500 Operation
CONNECTING THE TMM4500 DISPLAYS
There are four sets of video input connectors on the TMM4500 in the standard four-display configuration.
Additional video interface options may include:
Other video interface options may be available for specialized applications.
The silk screen located above the video connectors indicates the video interface connection type. Some
video input connectors may not be populated depending on your specific TMM4500 product configuration.
Use the appropriate video interface cable to connect each video input connector to the corresponding video
output source.
BACK PANEL LAYOUT AND CONNECTING TMM4500 POWER
Illustrated below is a typical back panel layout for a 4-screen TMM4500 configuration. Using the
information below, connect power and ground to the unit and ensure that the desired video connections
between the TMM4500 and the video source devices are secure.
A. Video Inputs and optional I/O connections
B. Power Input 0 This is the 12VDC input from the external 100-240VAC power supply adapter
C. Chassis Ground
VGA DVI-D HDMI YPbPr Composite
HD-SDI Display Port
A
B
C
4-1 Trenton Systems, Inc.

TMM4500 Reference Guide
DEPLOYING THE TMM4500 –BASIC DISPLAY DRAWER OPERATION
CAUTION
Ensure that the TMM4500 is securely mounted in the component
rack before opening and extending the display drawer.
The display head of the TMM4500 contains the majority of the unit weight. Failure to secure the unit before
sliding open the display drawer will cause the unit to tip forward and may result in system damage or injury.
For pre-installation, testing situations the back of the unit should be secured to a stable surface or countered-
weighted to prevent the unit from tipping forward.
Follow the steps below to open the TMM4500 display drawer, slide out the display assembly and rotate and
rotate the display assembly to the stable-deployment position.
STOWED POSITION
1.Unscrew the four
thumb screws located
on the unit’s front face
FULL EXTENSION
2.Pull drawer out
3.Unlock the two ¼ turn latches
4.Fold front face down 180 degrees
FULL EXTENSION - UP
6.Release any display securing
latches that may be engaged
7.Grab back of display head
8.Lift display head up 90°
STABLE – VERTICAL
5.Push the display head into the
stable up position just far enough
the clear the component rack,
transit case or pre-installation test
station
ROTATION MANEUVER
10. Ensure front face is hanging
straight down at 180° as shown
11.Rotate display head 90°
STABLE - HORIZONTAL
9.STOP! Before opening the display
head, the front face must be setup
to enable the display head module
stop. See the next step.
Trenton Systems, Inc. 4-2

TMM4500 Reference Guide
DEPLOYING THE TMM4500 –SETTING UP THE DISPLAY HEAD MODULE STOP
The information and illustrations below will enable you to properly set-up the display head module stop.
This step is important because the module stop ensures a stable display reading experience in typical
application environments.
Display Front Face Hardware Overview
1. Thumb Screws
The four (4) thumb screws are used to
secure the assembly into the component
rack.
2. Quarter-Turn Latches/Receptacles
These quarter-turn fasteners are used to
secure the front face to the display
drawer.
3. Display Module Lock Down Latches
The lockdown latches are used to secure
the modules when stowed for transit.
4. Rubber Bumpers
The rubber bumpers are used as stops
and prevent the display module head
from moving once the screens are
deployed.
UNLOCK
3.Unlock display head
assembly lock downs
FOLD
2.Fold front face as shown
SECURE
1.Secure front face into the
display drawer using the
quarter-turn latches
The multi-head display of the TMM4500 is now ready for deployment.
4-3 Trenton Systems, Inc.

TMM4500 Reference Guide
Chapter 5 -Unified Button Board Operation
The TMM4500 includes an On-Screen Display (OSD) button board for use with multi-display systems. In
the past each panel required its own OSD button board and controls to manage the basic display functions.
The single unified OSD button board mounted on the center screen allows the user toggle control
functionality of each individual display or all of the panels at once. This single OSD management feature
brings a new level of control to multi-screen display systems.
OSD BUTTON BOARD LAYOUT
The OSD button board located on display screen one (1), i.e. the center display screen, is illustrated below.
The basic functions of the OSD button board are:
• Power Button – Turns the TMM4500 on and off
• Menu – Activates the OSD set-up menu
• Navigation & Hot Keys, Up Arrow – Brightness
• Navigation & Hot Keys, Down Arrow – Auto-Calibrate (VGA Only)
• Navigation & Hot Keys, Left Arrow – Contrast
• Navigation & Hot Keys, Right Arrow – Activates Volum3
OSD INDICATOR LIGHT DEFINITIONS
The OSD button board has a bank of four (4) LEDs that indicate LCD display status.
Here are the definitions of the OSD indicator lights:
• Red – Power is applied to an individual display screen, but no active video source is detected.
• Green – Power is applied to an individual display screen, and an active video source is detected.
• Blue – In the example above, display screen 1 is selected or “in focus”.
• Focus Options – Display screen selection is accomplished by using the Panel Select + or - buttons
shown below
Reset / No Focus Panel 1 Focus Panel 2 Focus Panel 3 Focus Panel 4 Focus All Panel Focus
NOTE: The unified button board supports up to four displays. TMM4500 configurations with fewer than
four displays will have LEDs that are not populated.
RED GREEN BLUE- Display 1
No Video Good Video Shows Current
Signal Signal Status
5-1 Trenton Systems, Inc.

TMM4500 Reference Guide
Chapter 6 -Maintenance and Troubleshooting
If you have a problem setting up or using this product, refer to the suggested actions in this chapter to
troubleshoot the problem. You may also want to consult the video card user’s manual section for
additional troubleshooting advice.
MAINTAINING THE TMM4500
To maintain the TMM4500 and to keep the unit operating at peak performance:
• Keep the display screen clean
• Adjust the OSD controls for optimum display performance.
• Keep all ventilation openings clean and occasionally vacuum the openings to remove any
accumulation of dust or dirt.
• Do not block ventilation openings with objects or install the TMM4500 in a place where
ventilation may be obstructed. Always maintain adequate ventilation to protect the TMM4500
from overheating and to ensure reliable and continued display operation.
TROUBLESHOOTING THE TMM4500
Problem
Possible Causes and Solutions
No image displayed (blank screen)
Is the unit receiving power? Check that the computer’s power cable is
connected properly and securely into a grounded electrical outlet.
Check that the monitor’s power cable is connected properly and
securely to an electrical outlet. Check that the panel is in a raised
position for the power switch to automatically activate. Try using
another electrical outlet.
Is the unit receiving a valid video signal from the PC or video
source? Check that the
computer/video source is powered on. Check that the video cable is
connected properly and securely to the computer/video source.
Check that no pins are bent in the video cable connector. Check that
the video card is firmly seated in the card slot in your computer.
Is the unit in Power Management mode? Touch the screen (if
applicable), press any key on the keyboard, or use the touch pad to
restore operation. Are the brightness and the contrast settings too
low? Use the monitor controls to adjust these values.
Abnormal image
Check that the video signal is within specifications for the monitor
Check that the video cable is connected properly and securely to the
computer.
Image colors are abnormal
Check that the video cable is connected properly and securely to the
computer.
Check that no pins are bent in the video cable connector.
Check that a magnetized object is not nearby.
Check the settings under the color balance options.
6-1 Trenton Systems, Inc.

TMM4500 Reference Guide
TROUBLESHOOTING THE TMM4500 (CONTINUED)
Problem
Possible Causes and Solutions
“Video Mode Not Supported”
message
Check the maximum resolution and the frequency on the video port of
your computer. Compare these values with the data in the Display
Modes Timing Chart.
Image is too dark or too light
Adjust the display’s Brightness and Contrast
Horizontal bars appear to flicker,
jitter or shimmer on the image
Adjust the Fine function
Vertical bars appear to flicker, jitter
or shimmer on the image
Adjust the Coarse function and then adjust the Fine function
Image is not stable and may appear
to vibrate
Check that the display resolution and frequency from your PC or video
board is an available mode for your display screen. On your computer
check: Control Panel -- Display Settings, if the setting is not correct,
use your computer utility program to change the display settings.
Horizontal Frequency: 30kHz ~ 61kHz
Vertical Frequency: 50kHz ~ 75kHz
Maximum Refresh Rate: 1280 x 1024 @ 75Hz
Image is not centered on a display
screen
Adjust the screen’s horizontal and vertical positions
Display screen video cable not
connected
If power is applied to the unit without the video cable connection
between a display screen and the computer, one of the following on-
screen messages will be displayed:
“No Signal Going to Sleep” or “No Signal”
The OSD adjustment buttons are inactive for the unconnected display
screen. This message will appear for 10 seconds before turning off. If
the video cable is connected to the computer, this information is not
displayed.
Video Signal Out of Specification
If the video sync signals do not
meet the monitor specifications, the
unit will display the following
screen:
Out of Range
– or –
Invalid Mode FH: 93.6 KHz
FV: 74.9 Hz
The message will detail the current horizontal and vertical scan
frequencies, which the LCD panel does not support. This message will
appear for 15 seconds before turning off.
Trenton Systems, Inc. 6-2

TMM4500 Reference Guide
Chapter 7 - TMM4500 Specifications
ENVIRONMENTAL
Temperature
Operating
0°C to 50°C
Storage
-20°C to 60°C
ELECTRICAL
TMM4500 Input Voltage
+12VDC
Power Supply Adapter Line Voltage &
Power
100-240VAC, 175W
Line Frequency
50-60Hz
PHYSICAL
TMM4500Approximate Dimensions
(W x H x D) 4-Screen Configuration
19” x 7.0” x 26.0”
48.30cm x 17.78cm x 66.04cm
Net Weight
85 lbs. (38.59 kg)
DISPLAYS
Type
21.5” WFHD, 1920 x 1280, LED backlight
Brightness
250 NITS
Viewing Angle
89° Left of vertical center and 89° Right of vertical
(178° total), 89° Up over horizontal center and 89°
Down from horizontal center (178° total)
Color Depth
16.7M
Contrast Ratio
1000:1
Response Time
8ms G to G Latest
SAFETY STANDARDS
The product(s) described in this manual have been
designed and built to meet the safety requirements of
Underwriters Laboratories (UL) for the US and
Canadian market based on UL’s published Standards
for Safety.
The product (s) described in this manual have been
designed and built to meet the safety requirements of
TUV Rhineland for the European Union and is based
on the Low Voltage Directive.
7-1 Trenton Systems, Inc.