Triclimb ARCHI Original instructions

ARCHI – Folding Rocker and Climber
GB - ASSEMBLY INSTRUCTIONS, MAINTENANCE AND SAFETY INFORMATION
Suitable for ages 0+ | Weight limit – 50kg (100kg when connected to the Triclimb base unit)
ENCOURAGE – ENHANCE – ENGAGE
TRICLIMB - Encouraging children to develop motor skills independently in their own time, to enhance their
creativity and to become engaged in problem solving.
Benefits of Play – Triclimb products provide a surface designed for climbing which is intended for young
children. Younger children are still developing a sense of judgement and learning the strength of their own
bodies. They will be testing how far and how high they can jump and move. Their balance is still under
development, and they are learning how to solve physical problems using their bodies. The Triclimb products
therefore provide a chance to develop all sorts of skills appropriate to their age; climbing gives them the
opportunity to test, retest and perfect their strength, coordination, self-confidence, concentration and
independence.
Designed and built to the highest safety standards using FSC certified timber, our products are extremely
strong and sturdy. All products are independently tested (EN71:1, 2, 3 and 8) giving you peace of mind.
CARE INSTRUCTIONS
Caring for your Triclimb Archi is not only essential for ensuring safety, but will also add years to its life for
your children to play on and enjoy it as they grow.
WARNING: If the checks and maintenance of the Triclimb Archi are not carried out the activity toy could
overturn or otherwise become a hazard.
*All bolts and fixings should be checked regularly and tightened if necessary.
*It is important to check your Triclimb Archi for wear and damage regularly. If you are unsure as to the
integrity of any component, replace it immediately.

*It is extremely important that you read and retain the information in this WARNINGS section to
reduce the
risk of injury.
*Children must be supervised at all times while using the Triclimb Archi.
*No running, pushing or fighting.
*Only use the Triclimb Archi for its intended purpose. For indoor use only, in a domestic setting.
*Tip over hazard - Place play-frame on a level surface.
*Do not allow children to play on the Triclimb Archi until the unit is fully opened.
*Keep floors free of trip hazards and observe an obstacle free safety zone of at least 2m in all
directions
around the unit.
*To minimize risk of injury from falling, do not install over a hard surface; a protective surface
should be used.
Maximum vertical fall height - 525mm
*Never allow children to play with ropes, clotheslines, pet leads, cables, chains or cord-like items
when using
this play-frame or to attach these items to the play-frame.
*Never allow children to wear loose fitting clothing, ponchos, hoods, scarves, capes, necklaces,
items with
draw-strings, cords or ties when using this Triclimb Archi.
*Do not allow children to wear open toe or heel footwear like sandals or flip–flops whilst climbing.
*Do not permit rough play or use of equipment in a manner for which it was not intended. Jumping
from the
top, elevated rungs could be dangerous.
*Observe capacity limitations of your play-frame - 1 user maximum.
*Recommended age: 0 months +
*Weight limit – 50kg (100 KG when connected to the Triclimb base unit.)
*Not suitable for children under 36 months until fully assembled – fall hazard and small parts –
choking
hazard.
*Risk of entrapment when folding. Never allow children to open and close the frame – ensure the
thumb
screws are secure both in the open position and the folded position. WARNING – periodically
check thumb
screws to make sure they are securely in place.
WARNINGS
*We recommend that you regularly check your climbing frame for splits, broken or cracked wood
and for
loose, missing or sharp-edged hardware. Replace, tighten and/or sand smooth as required prior to
playing.
*The wooden components are manufactured from FSC birch plywood and solid timber poles; they
are
protected with a durable child/toy-safe finish.
*To clean, wipe with a damp cloth and mild detergent. Dry immediately. Leaving water or cleaning
agent on
the surface may damage the finish. Do not use abrasive cleansers.
* Do not modify the unit. Triclimb is not responsible for any injury arising as a result of
modifications made by
customers to our products without our supervision, testing, or evaluation.
* Do not modify the unit. Triclimb is not responsible for any injury arising as a result of
modifications made by customers to our products without our supervision, testing, or evaluation.

Tools needed:
Hex head Allen key (provided) | Mallet or hammer. A rubber mallet is ideal; if using a wooden
mallet or claw hammer please ensure suitable protection is applied to surface of the Archi.
ASSEMBLY GUIDE
AClimbing Rungs x 8
BFlat Rails x 2
CFlat Rails with cut out x 2
DLeg sets (assembled) x 2
EFlat head screws (hex head) x 24
F Thumb screws x 2
GHex head Allen key x 1
Contents
A
B
C
D
E F G
1
Place the pre-assembled legs (D) flat on the floor with the larger rung holes facing up. Using the pre-inserted dowels
locate one of the flat rails with a cut out (C) with the cut out facing down to the corresponding holes on the legs
over the joint in position 1. Place the second rail with cut out (C) at position 2 with the cut out facing up. Locate the
remaining two rails (B) in positions 3 and 4. TIP: you may need to use some side to side motion to fully engage the
rails.
Items required:
B x 2 C x 2 D x 1
1
2
3
4
1
2
3
4
Cut out facing up
Cut out facing down

2
Ensure all rails are flush with the leg. Turn the
assembly on its side. Insert flat head screws (D)
into each rail and tighten using the hex key
provided.
Items required:
E x 4 G
Connect the rungs (A) x 8 to one pair of legs. One
at a time, place the rungs into the recessed holes
on the legs. Insert flat head screws (E) and tighten
using the hex key provided. Note: ensure you hold
the pole with one hand to stop it spinning as you
tighten the screws.
Items required:
A x 8 E x 8 G
3
Turn assembly so that the legs are flat on the
floor. Make sure the leg set is closed. This will help
with the next part of the assembly process.
4
Place the second pre-assembled leg set on top of
the current assembly. Make sure the larger
recessed holes locate to the poles.
Locate the dowels to their corresponding holes
first – at this stage they only need to just sit in
the leg holes.
Items required:
D x 1
5

Starting at the joint end – gently start to
tap above each dowel point a little at a
time, working your way down to the
bottom dowel. You may need to move the
poles into the recessed holes. Repeat until
all dowels are in place and all poles are in
place. TIP: you may need to use a rubber
mallet to fully engage the wood dowels in
the rails. (If using a hammer, please use a
scrap piece of wood to protect your Archi.)
6
7Ensure all rungs are securely inserted into
leg recesses and then insert flat head
screws (E). All screws should be tight and
rungs should not be able to move or turn
easily. Tightening the screws requires
significant strength; this is to ensure they
do not spin or become loose during use.
Items required:
E x 12
G
Check whether your Archi sits flat on the ground. If not, you will need a book (or
something similar) about 40mm thick to act as a raiser. Perform the following steps:
CHECK POINT
1) Open the Archi frame and insert the thumb screws.
2) Place the book or similar under one of the two opposing legs
that are flat to the ground.
3) Push down on the top joints. You may hear a creaking sound -
do not be alarmed, this is just the frame moving into correct
alignment.
4) Remove the book or similar and repeat step 3.
5) You should now have a correctly aligned frame.
If there is still a slight wobble, simply increase the size of the
raiser and repeat step 2 and 3.

OPENING AND CLOSING
OPEN CLOSED
Your Archi includes two thumb screws that are designed to lock the product in an open or closed position.
To open the Archi:
1) Fully unscrew and remove both thumb screws from the sides of the unit
2) Holding the unit at the bottom edges, carefully open the unit. The mechanism may be sti.
3) Once fully open, replace both thumb screws into the unit prior to use.
Closing the unit is the reverse of opening.
WARNING: Opening and closing should be attempted by adults only. The thumb screws are an important
safety feature and should always be fully inserted prior to use or storage.
DIMENSIONS: Open: L1060 x W500 x H525mm Folded: L470 x W500 x H745mm Approx.
The Archi has been designed to work as a standalone rocker or climbing frame. But it can also be used in
conjunction with several other products within the Triclimb range.
The rocker has our innovative Trifix system built in which means you can connect it directly to a second
Archi or a Triclimb frame without the need for any additional joints or tools – it works in the same way as
the Triclimb attachments (e.g. the Miri or Wibli.) LIFT- SET- DROP
Combinations:
1) Archi + Attachment
2) Archi + Triclimb*
3) Archi + Attachment + Triclimb
4) Triclimb* + Archi + Triclimb* + Attachment
*Original or Mini
1

2
33
4
WARNING: If using one Triclimb, the Archi must only be connected to the Triclimb/Mini using the
bottom two CLIMBING rungs of the Triclimb/Mini (not counting the longer bottom rungs that sit on the
ground) (Fig 2)
If using two Triclimbs, the Archi must only be connected to the Triclimb/ Mini using the following
combinations: - First to first CLIMBING rungs of the Triclimb/Mini (Fig 4) or First to second CLIMBING
rungs of the Triclimb/Mini
PLEASE NOTE: Archi has been independently laboratory tested (EN71:1, 2, 3 and 8) as a rocker and as
climber on and o the Triclimb base units.

IPO - Registered design.
Model – TC: Archi
Designed and Manufactured by Triclimb Ltd.
Ty Gelert, Penamser Road, Porthmadog, Gwynedd, LL499NX, Wales UK
www.triclimb.co.uk [email protected]
IMPORTANT! These instructions must be followed for safe assembly and use.
Please retain for future reference. 2019 V1
CONNECTING - Archi to a Triclimb
Prior to use you must ensure you lock the attachment in place using our specially designed locking method to
ensure it does not move whilst in use. The connection is the same as that used on the Triclimb to connect an
attachment. Simply – LIFT – SET – DROP
1) Lift one side of the Triclimb o the floor by a few inches.
2) Carefully bring the Archi to the desired rung and hook the shallow cutouts over the rung as shown in
figure 2
3) Gently drop the Triclimb to the floor and the Archi will become locked in position.
REMOVING the accessory is the reverse of connecting.
1 2
33
CONNECTING - An attachment to your Archi
Prior to use you must ensure you lock the attachment in place using our specially designed locking method to
ensure it does not disengage whilst in use. The connection is the same as that used on the Triclimb to connect
an attachment. Simply – LIFT – SET – DROP
1) Lift one side of the Archi o the floor by a few inches.
2) Carefully bring the attachment to the desired rung and hook the shallow cutouts over the rung.
3) Gently drop the Archi to the floor and the attachment will become locked in position.
REMOVING the accessory is the reverse of connecting.