Tripp Lite DMCS3270XPBB User manual

1
Owner’s Manual
Mobile Flat-Panel
Floor Stand
Model: DMCS3270XP
CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support
Copyright © 2021 Tripp Lite. All rights reserved.
200 x 200 / 300 x 300
400 x 200 / 400 x 400
600 x 400
70”
MAX
150 lb.
150 lb.
(68 kg)
(68 kg)
MAX
MAX
Este manual está disponible en español en la página de Tripp Lite: tripplite.com
Ce manuel est disponible en français sur le site Web de Tripp Lite : tripplite.com
Русскоязычная версия настоящего руководства представлена на веб-сайте компании
Tripp Lite по адресу: tripplite.com
Dieses Handbuch ist in deutscher Sprache auf der Tripp Lite-Website verfügbar: tripplite.com
WARRANTY REGISTRATION
Register your product today and be
automatically entered to win an ISOBAR®
surge protector in our monthly drawing!
tripplite.com/warranty

2
NOTE: Read the entire instruction manual before you start installation and assembly.
Warranty & Product Registration
WARNING
• Do not begin the installation until you have read and understood the instructions
and warnings contained in this manual. If you have any questions regarding any
of the instructions or warnings, please visit tripplite.com/support.
• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone of good mechanical ability, with
basic building experience and a full understanding of this instruction manual.
• Make sure that the mounting surface can safely support the combined load of
the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. The use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over-tighten. Over-tightening screws can
damage the items, greatly reducing their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
5-Year Limited Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects
in material and workmanship for a period of 5 years from the date of initial purchase. If the product should
prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole
discretion.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE,
ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY
SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES,
INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY
PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL
DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions
may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from
jurisdiction to jurisdiction).
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate
or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes
no representation or warranty as to the suitability or fitness of these devices for any specific application.
PRODUCT REGISTRATION
Visit tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a
drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice. Photos and
illustrations may differ slightly from actual products.

3
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to
installing. If any parts are missing or faulty, visit tripplite.com/support for service.
Middle Base
A
M5 x 14 Screw (x4)
M-A
M6 x 16 Screw (x8)
Q
M6 x 8 Screw (x6)
V
M8 x 50 Screw (x4)
M-F
Support Plate
F
Connecting Plate
M
Column
J
Universal Plate
G
Camera Shelf
N
Plastic Handle
K
Plastic Cover (x2)
H
DVD Shelf
O
Top Cover
L
Adapter Bracket (x2)
I
Washer (x4)
P
Caster (x4)
A-1
Left Leg
B
M6 x 14 Screw (x4)
M-B
M6 x 25 Screw (x3)
R
M8 x 25 Screw (x4)
W
Washer (x4)
M-G
M8 x 20 Screw (x4)
M-C
M4 x 6 Screw (x3)
S
M5 x 8 Screw (x2)
X
Small Spacer (x8)
M-H
M6 x 30 Screw (x4)
M-D
M4 x 6 Screw (x4)
T
Allen Wrench
Y
Big Spacer (x8)
M-I
M8 x 30 Screw (x4)
M-E
M6 x 14 Screw (x2)
U
Wrench
Z
Right Leg
C
Left Cover
D
Right Cover
E
Package M
Package P

4
1. Assembling the Base
2. Attaching the Column to the Base
Q
A-1
Z
Y
Y Y
1) Insert Right Leg Cinto Middle Base A. Align the holes in the Right Leg to the holes in the Middle Base.
Secure with Screws Qand Allen Wrench Y. Repeat this step for Left Leg B.
2) Each caster can be adjusted independently for fine tuning. Slightly turn the nut with Wrench Zto lower or
raise Middle Base.
Adjust inner Column Jto the desired height, then tighten all screws.
CAUTION: Hold the inner column
when loosening the screws to adjust
height.
Never
Overtighten
Screws

5
2. Attaching the Column to the Base
K
Y
W
R
Place Plastic Handle Kon Column.
Attach Column to Middle Base with
Screws W. Tighten all screws, then
tighten Safety Screw Rwith user-
supplied Phillips-head screwdriver.
Attach Left Cover Dand Right Cover Eto Legs.
D
E

6
3. Installing the Support Plate
4. Installing the Adapter Brackets
L
U
F
Attach Support Plate Fto Column with Screws Uand
user-supplied Phillips-head screwdriver. Attach Top Cover
Lto Support Plate.
Insert Washers Pinto
back of Universal Plate
Galong plate rails.
Insert Adapter Brackets Iinto Universal Plate. Align holes in Adapter Brackets
to holes in Washers. Insert Screws Q, but do not tighten them yet.
P
Q
Y

7
4. Installing the Adapter Brackets
Attach Plastic Covers Hto both ends of
Universal Plate using Screws V. Tighten
all screws with user-supplied Phillips-
head screwdriver.
Adjust Adapter Brackets to fit VESA hole pattern on your display. Tighten all Screws.
NOTE: Verify proper alignment of all holes.
H V
Y
min. 200 mm - max. 600 mm
min. 200 mm - max. 400 mm

8
M-C
M-C
M-F M-F M-F
M-C
M-D
M-E
M-D
M-E
M-D
M-E
M-G
M-G M-G
M-G
M-G M-GM-G
M-H
M-H
M-I M-H
M-I
M-H
M-I M-I M-I
M-H
4. Installing the Adapter Brackets
4.1 For Flat-Back Screens
4.2 For Recessed-Back Screens or Accessing A/V Inputs
M-G
M-A
M-B
M-C
Note: Choose the appropriate Screws, Washers and Spacers (if needed) according to the type of screen.
Screw the Adapter Brackets onto the display.
CAUTION: Tighten all screws but do not over tighten.
Note: Choose the appropriate Screws, Washers and Spacers (if needed) according to the type of screen.
Screw the Adapter Brackets onto the display.
CAUTION: Tighten all screws but do not over tighten.
or
or or
or or

9
Lever
Plastic
Holder
T
5. Hooking the Display to the Support Plate
6. Installing the DVD Shelf
Hook Universal Plate onto Support Plate. Secure by tightening Screws Xwith user-
supplied Phillips-head screwdriver.
X
CAUTION: Be sure the display is correctly mounted and that the screws are safely tightened
before releasing the display.
Insert the two plastic
holders of DVD Shelf
Ointo slots.
Close lever to lock
DVD Shelf.
Tighten Screws Tto
secure.

10
8. Installing the Camera Shelf
7. Cable Management
Attach Camera Shelf Nto Connecting
Plate Musing Screws S& T. Tighten
screws with user-supplied Phillips-head
screwdriver.
S
T

11
9. Installing the Connecting Plate
10. Display Orientation
Attach Connecting Plate to Column at the
desired height using Screws R. Tighten
screws with user-supplied Phillips-head
screwdriver.
Install at least two Screws V
diagonally to secure the display.
Remove the two
screws to rotate the
display 90° clockwise.
Retighten the removed screws
into the different hole position
to secure the display.
R
For Landscape View For Portrait View
or
V

12
1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support
21-06-083 93-36AF_RevC
Maintenance
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
• For any additional questions, visit tripplite.com/support.
11. Adjustment
Loosen the knobs to
adjust the display to
the desired angle.
Tighten the knobs to
secure.
Display panel center
height measured
from floor.
Y