Gared 2500 Manual

Wall Mount
Models: 2500
Installation, Operation and Maintenance Instructions
Please read all instructions before attempting installation or operation of these units
SAVE THESE INSTRUCTI ONS FOR FUTURE USE
P UBLICATION N O . Revised
5 0 1 7 5 2 9 3 7 October 16 , 2009

2500 Wall Mount
TABLE OF CONTENTS
Section Page No.
Introduction 2
Notice to Installers 3
Cautions and Warnings 4
Model Information 5
Parts List 6
Kits List (Kits contained within the Parts List) 7
Tools Required 10
Wood Pad Installation 11
Special Bracket Considerations 13
Unit Installation 14
Operation Guidelines 17
Maintenance 18
Maintenance Checklist 19

2500 Wall Mount
2
INTRODUCTION
Thank you for your purchase of a Model 2500 Wall Mounted Backstop . To ensure that
our equipment will provide years of use to you, we are including this installation, operation, and
maintenance guide. This guide will provide information on the proper assembly and installation
methods, operating procedures, and preventative maintenance of your wall mounted backstop .
Please do n ot substitute for factory parts!
Please contact your custom er service representative and allow them to determine if substitute
parts are acceptable.
It is recommended that an individual who has been properly trained perform assembly
and set up of the backstop . No one under the age of 18 should attempt assembly o r set up of the
unit, unless properly supervised.
To prevent normal wear and tear from shortening the life of the unit, preventative
maintenance inspections and repairs should be performed at least once per year. If the units are
subject to high or unusu al usage, inspections should be scheduled to occur more frequently. If
items are found to be nonconforming, replacements can be ordered factory or one of our
authorized dealers. When contacting Gared Sports or Performance Sports Systems , please have
information regarding the dealer/installer who sold the unit, the name of the project, and any
applicable warranty information.

2500 Wall Mount
3
NOTICE TO INSTALLERS
The following instructions are meant as a guide only. This guide is intended to assist you with
the install ation and operation of the Model 25 00 Wall Mounted Backstop. Jobsite conditions
will be different for each project, and conditions may change during the project. Any
suggestions or tips contained herein are for general information, and may not apply to y our
particular installation.
Please contact Gared /PSS for additional information if you are unsure how to proceed with the
installation at any time, or if jobsite or building conditions change before or during this
installation, thus affecting the corr ect installation of this unit .
It is imperative to inspect all material being used in this installation BEFORE you begin.
Confirm that materials and parts received correspond to those listed on the packing list and
production drawings. If any materials or parts have been damaged during shipping or are
missing as a result of shipping, you must file a freight claim with th e delivering freight company.
Missing or damaged material must also be noted on the Bill of Lad ing at the time of delivery.
If materials or parts are determined to be missing due to factory error or oversight, contact
Gared /PSS immediately at 800 -325-2682/ 800-848-8034.
Follow all local safety codes and OSHA regulations. Gared /PSS will not be held liable, in any
way, for improper installa tion or faulty workmanship at the jobsite.
Before proceeding with assembly. READ ALL INSTRUCTIONS AND ASSEMBLY
PROCEDURES. Make sure all parts have been received and are not damaged.
This backstop has been manufactured in accordance with the specificatio ns provided by the
Owner/Architect.

2500 Wall Mount
4
CAUTIONS AND WARNINGS
Read and understand the following warnings to prevent possible personal injury and potential
damage to the equipment during assembly, setup, and operation.

2500 Wall Mount
5
MODEL INFORMATION
MODEL NU MBER DEFINITION
MODEL
2300 – 4 point stationary
2350 – 3 point stationary
2400 – 4 point fold up
2500 – 4 point side fold
EXTENSION
203 – 2’ to 3’ (see installation drawings for exceptions)
304 – 3’ to 4’ (see installation dr awings for exceptions)
406 – 4’ to 6’ (see installation drawings for exceptions)
609 – 6’ to 9’ (see installation drawings for exceptions)
912 – 9’ to 12’ (see installation drawings for exceptions)
BOARD
0 – FAN SHAPED MOUNTING (NARROW FRAME – 35”)
4 – RECTANGULAR BOARD MOUNTING (WIDE FRAME – 63”)
ADJUST -A-GOAL
A – With Adjust -A-Goal
Blank – Without Adjust -A-Goal
2300
203
A
MODEL
EXTENSION
ADJUST -A-GOAL
X
BOARD

2500 Wall Mount
6
PARTS LIST
2500 SIDE FOLD WALL MOUNT
EXTENSION
PART NUMBER:
QTY:
DESCRIPTION:
4-6'
6-9'
9-12'
1040-30-00
10 ft
4/O STRAIGHT COIL CHAIN - ZINC
X
1040-30-00
17 ft
4/O STRAIGHT COIL CHAIN - ZINC
X
1040-30-00
24 ft
4/O STRAIGHT COIL CHAIN - ZINC
X
154151696
1 ea
HARDWARE KIT, WALL MOUNT UNITS
X
X
X
154151698
1 ea
CHAIN SUPPORT KIT
X
X
X
154151699
1 ea
SINGLE BRACE KIT
X
154151702
1 ea
SIDE FOLD ADDER KIT
X
X
X
154154093
1 ea
SIDE FOLD ADDER KIT (NARROW NON - AAG ONLY)
X
X
X
501752937
1 ea
MANUAL, 2500 SIDE FOLD WALL MOUNT
X
X
X
504151652
4 ea
PIPE, FU. INNER, 4 -6'
X
504151655
4 ea
PIPE, FU. OUTER, 4 -6'
X
504151653
4 ea
PIPE, FU. INNER, 6 -9'
X
504151656
4 ea
PIPE, FU. OUTER, 6 -9'
X
504151654
4 ea
PIPE, FU. INNER, 9 -12'
X
504151657
4 ea
PIPE, FU. OUTER, 9 -12'
X
504152686
1 ea
INNER SLIDE TUBE A (N ARROW FRAME)
X
504152687
1 ea
OUTER SLIDE TUBE A (NARROW FRAME)
X
504152688
1 ea
INNER SLIDE TUBE B
X
X
504152689
1 ea
OUTER SLIDE TUBE B
X
X
504152690
1 ea
INNER SLIDE TUBE C (WIDE FRAME)
X
504152691
1 ea
OUTER SLIDE TUBE C (WIDE FRAM E)
X
504152692
1 ea
INNER SLIDE TUBE D (NARROW FRAME)
X
504152693
1 ea
OUTER SLIDE TUBE D (NARROW FRAME)
X
504152694
1 ea
INNER SLIDE TUBE E (WIDE FRAME)
X
504152695
1 ea
OUTER SLIDE TUBE E (WIDE FRAME)
X
504151670
2 ea
STRAP BRACI NG, 48" (NARROW FRAME)
X
504151672
2 ea
STRAP BRACING, 69" (WIDE FRAME)
X
504151671
2 ea
STRAP BRACING, 60" (NARROW FRAME)
X
504151673
2 ea
STRAP BRACING, 78" (WIDE FRAME)
X
504151670
4 ea
STRAP BRACING, 48" (NARROW FRAME)
X
504151 672
4 ea
STRAP BRACING, 69" (WIDE FRAME)
X
2500 SIDE FOLD WALL MOUNT - WOOD PADS
FRAME SIZE
PART NUMBER:
QTY:
DESCRIPTION:
504151591
3 ea
WOOD PAD, 3.5" HC, 48"
NARROW FRAME UNITS
504151590
3 ea
WOOD PAD, 3.5" HC, 72"
WIDE FRAME UNITS
2500 SIDE FOLD WALL MOUNT - W/ AAG
FRAME SIZE
PART NUMBER:
QTY:
DESCRIPTION:
153954405
1 ea
KIT, FAN BOARD TO AAG
NARROW FRAME UNITS
153954404
1 ea
KIT, RECT BOARD TO AAG
WIDE FRAME UNITS
154155287
1 ea
NARROW AAG TO WM FRAME KIT
NARROW FRAME UNITS
154155281
1 ea
KIT, AAG TO WM MTG, 4PT RECT
WIDE FRAME UNITS

2500 Wall Mount
7
KITS LIST
HARDWARE KIT, WALL MOUNT UNITS
PART NO. 154151696
QTY.
PART NO.
DESCRIPTION
1
1000-26-00
BANK BOLT HARDWARE KIT
1
1001-26-00
GLASS BOARD GOAL BOLT KIT
2
501-6-16-56
BOLT, CARRIAGE 3/8"x 3 1/2"
4
502-6-16-56Z
BOLT, HEX HEAD 3/8" -16 x 3 1/2"
8
501-6-16-32
BOLT, CARRIAGE 3/8" -16 x 2"
4
502-6-16-40
BOLT, HEX HEAD 3/8" -16 x 2 1/2"
8
502-8-13-56
BOLT, HEX HEAD 1/2" -13 x 3 1/2"
16
504151706
BUSHING, FOLDING UNITS
4
512-6-16-6
SET SCREW, ALLEN FLT PT 3/8"x 3/8"
4
545-6-16Z
NUT, NYLON LOCK NUT 3/8"
8
545-8-13
NUT, NYLON LOCK 1/2" -13 COARSE
8
548-6-16
NUT, WHIZLOCK 3/8"
CHAIN SUPPORT KIT
PART NO. 154151698
QTY.
PART NO.
DESCRIPTION
6
1113-30-00
5/16" QUICK LINK
4
501-6-16-32
BOLT, CARRIAGE 3/8" -16 x 2"
2
504151595
BRACKET, UPPER CHAIN/ PULLEY MOUNT
4
548-6-16
NUT, WHIZLOCK 3/8"
2
7011-11-00
3/8" TURNBUCKLE W/ BOTH EYES
SIDE FOLD ADDER KIT (FAN NON -AAG)
PART NO. 1541540 93
QTY.
PART NO.
DESCRIPTION
1
1030-02-08
LOCKING CLAMP, SIDE SWING WALL MOUNT
4
151651768
KIT, #116 TEE CLAMP
1
2183-02-00
#0183 - 1 7/8" TO 2 3/8"
16
501651854
SPACER BUSHING, 2 1/8" TO 2 3/8"
2
502-8-13-56
BOLT, HEX HEAD 1/2" -13 x 3 1/2"
2
504151 596
HINGE, SIDE FOLD SHORT
2
504151597
HINGE, SIDE FOLD LONG
2
504151600
HINGE, WOODPAD SHORT
2
504151601
HINGE, WOODPAD LONG
4
504151706
BUSHING, FOLDING UNITS
2
504151755
PLATE, BOARD BRACKET
1
504152629
LONG UPPER MOUNT, WALL
1
504152630
SHORT UP PER MOUNT, WALL
1
504152653
SLIDE TUBE WALL BRACKET
1
504152658
SLIDE TUBE BOARD BRACKET
4
504154091
TUBE, SIDE FOLD BRACE (FAN NON - AAG)
1
5042-02-00
1 7/8" MUFFLER CLAMP
2
545-8-13
NUT, NYLON LOCK 1/2" -13 X 2 1/2"

2500 Wall Mount
8
SIDE FOLD ADDER KIT
PART NO. 15 4151702
QTY.
PART NO.
DESCRIPTION
1
1030-02-08
LOCKING CLAMP, SIDE SWING WALL MOUNT
4
151651768
KIT, #116 TEE CLAMP
1
2183-02-00
#0183 - 1 7/8" TO 2 3/8"
16
501651854
SPACER BUSHING, 2 1/8" TO 2 3/8"
2
502-8-13-56
BOLT, HEX HEAD 1/2" -13 x 3 1/2"
2
504151596
HINGE, SIDE FOLD SHORT
2
504151597
HINGE, SIDE FOLD LONG
2
504151600
HINGE, WOODPAD SHORT
2
504151601
HINGE, WOODPAD LONG
4
504151706
BUSHING, FOLDING UNITS
2
504151755
PLATE, BOARD BRACKET
1
504152629
LONG UPPER MOUNT, WALL
1
504152630
SHORT UPPER MOUNT, WALL
1
504152653
SLIDE TUBE WALL BRACKET
1
504152658
SLIDE TUBE BOARD BRACKET
4
504152663
TUBE, SIDE FOLD BRACE
1
5042-02-00
1 7/8" MUFFLER CLAMP
2
545-8-13
NUT, NYLON LOCK 1/2" -13 X 2 1/2"
SINGLE BRACE KIT
PART NO. 154151699
QTY.
PART NO.
DESCRIPTION
2
1093-02-08
#93 STRAP CLAMP ASSEMBLY
1
151651766
KIT, #92 STRAP CLAMP
4
501651854
SPACER BUSHING, 2 1/8" TO 2 3/8"
1
502-6-16-16
BOLT, HEX HEAD 3/8" -16 x 1"
1
548-6-16
NUT, WHIZLOCK 3/8"
KIT, RECTANGLE BOARD TO AAG
PART NO. 153 954404
QTY.
PART NO.
DESCRIPTION
1
1000-26-00
BANK BOLT HARDWARE KIT
2
501-6-16-56
BOLT, CARRIAGE 3/8" x 3 1/2"
4
502-6-16-16
BOLT, HEX HEAD 3/8" -16 x 1"
2
502-6-16-56Z
BOLT, HEX HEAD 3/8" -16 x 3 1/2"
4
502-8-13-24
BOLT, HEX HEAD 1/2" -13 x 1 1/2"
2
503852349
BRACKET, ADJUSTABLE BOARD MOUNT
1
503853428
WELDMENT, DIRECT MOUNT EXTENSION
1
504151666
SUPPORT ANGLE, WM 63" CENTER
8
548-6-16
NUT, WHIZLOCK 3/8"
4
548-8-13
NUT, HEX, SERRATED FLANGE 1/2" -13

2500 Wall Mount
9
KIT, FAN BOARD TO AAG
PART NO. 153954405
QTY.
PART NO.
DESCRIPTION
1
1000-26-00
BANK BOLT HARDWARE KIT
4
502-6-16-16
BOLT, HEX HEAD 3/8" -16 x 1"
2
501-6-16-56
BOLT, CARRIAGE 3/8"x 3 1/2"
2
502-6-16-56Z
BOLT, HEX HEAD 3/8" -16 x 3 1/2"
4
502-8-13-24
BOLT, HEX HEAD 1/2" -13 x 1 1/2"
2
503852349
BRACKET, ADJUSTABLE BOARD MOUNT
1
503853428
WELDMENT, DIRECT MOUNT EXTENSION
1
504151667
SUPPORT ANGLE, WM 35" CENTER
8
548-6-16
NUT, WHIZLOCK 3/8"
4
548-8-13
NUT, HEX, SERRATED FLANGE 1/2" -13
KIT, AAG TO WM MTG, 4PT RECT
PART NO. 154155281
QTY.
PART NO.
DESCRIPTION
8
502-6-16-24
BOLT, HEX HEAD 3/8" -16 x 1 1/2"
4
502-8-13-32
BOLT, HEX HEAD 1/2" -13 x 2"
4
502-8-13-44
BOLT, HEX HEAD 1/2" -13 x 2 3/4"
1
504155373
FRAME, WIDE AAG TO WM ADAPTER BRACKET
8
548-6-16
NUT, WHIZLOCK 3/8"
4
548-8-13
NUT, H EX, SERRATED FLANGE 1/2" -13
KIT, NARROW AAG TO WALLMOUNT FRAME
PART NO. 154155287
QTY.
PART NO.
DESCRIPTION
8
502-6-16-24
BOLT, HEX HEAD 3/8" -16 x 1 1/2"
4
502-8-13-32
BOLT, HEX HEAD 1/2" -13 x 2"
4
502-8-13-44
BOLT, HEX HEAD 1/2" -13 x 2 3/4"
1
504155374
FRAME AAG, WM ADAPTER NARROW BRACKET
8
548-6-16
NUT, WHIZLOCK 3/8"
4
548-8-13
NUT, HEX, SERRATED FLANGE 1/2" -13

2500 Wall Mount
10
TOOLS REQUIRED
Electric Drill
Drill bits – 9/16”, 5/8”
Hammer
Wrenches – 1/2", 9/16”, 11/16, and 3/4"
Ratchet Wren ches with 1/2", 9/16”, 11/16, and 3/4" sockets
File
4’ Level
25’ Tape measure
Duct Tape
Block of wood (for tapping)
Broom
Shop-Vac
Utility Knife
Extra rope or chain

2500 Wall Mount
11
WOOD PAD INSTALLATION
Instructions for 2 500 Side Folding Wall Mounts
1) Wood pads are provided for use in anchoring the units to the walls.
2) Verify all dimensions and locations with the General Contractor using the latest
architectural prints before beginning. Also, verify floor thickness if not working over a
finished floor. NOTE: All production drawing dimensions override any dimensions
contained within this manual.
3) Mark the centerline of the unit on the wall utilizing the best method available.
4) Mark the centerline of the wood pad. Wood pads for rectangular boards are 72” w ide,
with predrilled bracket locations spaced 63” center to center. Wood pads for fan shaped
boards are 48” wide, with predrilled bracket locations spaced 35” center to center.
Anchors should be spaced to allow installation of chain and structure bracket s without
interference. The recommended layout is to have one anchor on each end of the wood
pad (center approximately 1 13/16” from the outer most edge of the wood pad) and two
evenly spaced in the center of the wood pad (see figure 1).
5) Next mark anchor locations on the wood pad and drill through.
6) Use the holes drilled in the wood pad as a template to mark the anchor holes on the wall.
Mark and drill the anchor holes in the wall. PSS recommends pads be bolted through the
wall with through bolts and an chor plates. When it is not possible to bolt through the
wall contact the structural engineer for the building for advice.
Figure 1. Generic w ood pad drawing with recommended anchor locations.
NOTE: Anchor holes should not be dri lled in line with each other or existing bracket holes.
7) Attach the brackets to the wood pad. Brackets for the chains should be spaced the same
as the pipe supports. NOTE: Attach the quick links and chains to the brackets prior
to anchoring the wood pads to the wall.
8) After all brackets are in place, anchor the wood pads in place on the wall, making sure to
place the wood pads for chains and supports in the correct locations (per F igure 2 ).

2500 Wall Mount
12
NOTE: Wood pad dimensions for reference only. See production drawing for final A, B, and C
dimensions. If production drawing cannot be located please contact the factory.
UNITS INSTALLED WITH OR WITHOUT AAG
ALL UNITS
DIM "A"
DIM "B"
FOB EXTENSION
DIM "C"
Rectangular or Wide Mou nting
0'-2' (0.0M -0.61M)
NONE
LXP 4200
9'-8 7/8" (2.97M)
36" (0.91M)
2'-4' (0.61M -1.22M)
24" (0.61M)
AFRG 42
9'-8 7/8" (2.97M)
36" (0.91M)
4'-6' (1.22M -1.83M)
35" (0.89M)
AFRG48
9'-2 11/16" (2.81M)
42" (1.07M)
6'-9' (1.83M -2.74M)
56" (1.42M)
RG
9'-2 11/16" (2.81M)
42" (1.07M)
9'-12' (2.74M -3.66M)
79" (2.00M)
1401B
9'-2 11/16" (2.81M)
42" (1.07M)
OVER 12'
*SEE JOB
1272PS
9'-7" (2.91M)
36" (0.91M)
1442B
9'-7 11/16" (2.94M)
36" (0.91M)
BB72A38
9'-6 5/8" (2.91M)
36" (0.91M)
Fan or Narrow Mounting
1342B
10'-1 7/8" (3.10M)
20" (0.51 M)
1301B
10'-1 5/8" (3.09M)
20" (0.51M)
FSGII
10'-1 5/8" (3.09M)
20" (0.51M)
1750B
9'-9 7/16" (2.98M)
20" (0.51M)
1270B
10'-0 7/16" (3.05M)
20" (0.51M)
1272B
10'-0 7/16" (3.05M)
20" (0.51M )
1260B
10'-0 7/16" (3.05M)
20" (0.51M)
3050RG
10'-3 15/16" (3.15M)
20" (0.51M)
1245T
9'-9 13/16" (2.99M)
20" (0.51M)
Figure 2.

2500 Wall Mount
13
SPECIAL BRACKET CONSIDERATIONS
Use the figures above to set up your hardware to match the directio n of fold desired. Check with
the General Contractor or Architect to confirm correct direction of fold. Note the placement of
the cross brace pipe hinge as shown in the detail below.

2500 Wall Mount
14
UNIT INSTALLATION
1) Prepare the extension tubes by inserting bushin gs as shown in figure 3.
Figure 3. Bushing installation (side view)
2) To attach the outer extension tubes to the wall brackets, use a hex bolt and nylon lock nut
as indicated on the installation drawing. Ensure that the tube will rotate through its
full range of motion after tightening the nut. Do not over tighten the nut.
3) The next step is to place the inner extension tubes into the outer extension tubes.
WARNING: The extension tubes must be temporarily roped or chained off in order
to hold them i n place.
Steps (4) and (5) apply to installations with an Adjust -a-Goal. Refer to instructions
received with AAG, for mounting board to AAG only. If you did not receive instructions
please contact factory. If your installation does not have an Adjust -a-Goal, please skip to
step ( 6).
4) The Adjust -a-Goal should be assembled prior to mounting to the extension arms and
prior to mounting the board.
5) While assembling the AAG on the ground, the AAG mounting frame can be installed on
the ends of the extension tu bes. Utilize eight of the 3/8” -16 x 1 1/4" hex head bolts with
washers and whiz -lock nuts to attach the support plates of the frame to the end brackets
of the extension tubes (r efer to figure 4 ).

2500 Wall Mount
15
Wide Narrow
Figure 4. Attach AAG mounting frame to extension tubes .
6) Connect the chains from the upper wood pad to the board mounting plate , utilizing the
quick links provided.
7) At this point, it is equally acceptable to attach the board or hoist the adjust -a-goal into
place at the end of the extension arms. The wall mount must be supported as this is done.
If you are attaching the board, utilize the 3/8” -16 x 1” ca rriage bolts at the top support
angle and the 3/8” -16 x 3.5” carriage bolts at the DME. To attach the adjust -a-goal, use
(4) ½” -13x 2” machine bolts and ½” -13 whiz -lock nuts .
8) After the board has been secured to the extension tubes, the board can be set to the proper
distance from the wall, as specified by the latest architectural drawings.
9) To temporarily retain the extension tubes at the proper length, tighten the setscrews
provided in the welded on T -nut, (see figure 5) . At this time, the board sho uld also be
squared and leveled.
Figure 5 . Close up of mating between inner and outer tubes, showing weld nut.
Weld nut and set
screw

2500 Wall Mount
16
10) To permanently set the length of the extension arms, drill 3/8” holes through the inner
tube at the predril led location on the outer extension arms. Secure the inner tube to the
outer tube with the provided hex head bolts and lock nuts (3/8”- 16x 2 ½”) .
11) Retighten the chains from the upper wood pad to the support angle, utilizing the quick
links provided.
12) The next step is to prepare the slide pipe to install. This consists of putting pipe A into
pipe B and temporarily securing them with the provided locking clamp.
13) Raise the slide pipe to the level of the side fold brackets and secure one end of the slide
pipe to one of the brackets using the ½ -13 x 3 hex bolt and ½ -13 lock nut provided.
NOTE: verify direction of folding with the latest copy of architectural drawings
prior to completing installation.
14) Next, s lide the other end of the slide pipe into the remaining side fold bracket and
secure with the ½ -13 x 3 hex bolt and ½ -13 lock nut provi ded, (as shown in figure 6) .
15) To complete the installation, attach the provided bracing pipes between the upper and
lower extension arm pipes with t he #116 t -clamps, (see figure 7) for an illustration.
Figure 6 . Slide pipe installation showing hinge brackets; slide pipes, and locking clamp.
Install slide pipe on lower exten sions.
Side fold wall
bracket
Side fold board
bracket
Locking clamp

2500 Wall Mount
17
116116
Figure 7 . Bracing pipes for side fold units installed between upper and lower pipes.
16) Retighten the chains.
OPERATION GUIDELINES
1) For all folding backstops, only a trained adult should operate the m anual and electric
winches.
2) Keep the areas below and around the units clear while they are in motion.
3) Do not over turn the manual winches. This could result in the supports running into each
other and binding the unit. Also, do not allow slack in the c able to develop, as this could
pose a safety hazard.
4) Always use the equipment in the manner intended. Performance Sports Systems does not
assume any liability for improperly used or improperly maintained equipment.
#116 t-clamp

2500 Wall Mount
18
MAINTENANCE
1) General inspection of equipment should be performed when the unit is used to ensure no
catastrophic failures have occurred during the course of use between yearly inspections.
2) It is recommended that yearly inspections be conducted to determine if any bolts, chain
links, or ot her hardware has become worn or loosened. A sample check sheet has been
provided for you in this guide.
3) During yearly inspections, all moving parts should be inspected while in operation. Key
points to look for include rotation points where bushings con tact metal, winches, pulleys
and quick links, and the cable. The cable should be carefully inspected for any fraying or
degradation of the apparent quality of the cable.
4) Any loose bolts or nuts should be tightened.
5) Check sliding components (AAG) for wea r and lubricate as needed.

2500 Wall Mount
19
MAINTENANCE CHECK SHEET
Date:________________ Unit:___________________
Wood Pads / Anchors
-Wood pads, splitting, chipping, etc. OK Repair Replace
-Anchors/Bolts OK Repair Replace
Unit Supports / Brackets / Hinges
-Tubes; dents, stress spots, etc. OK Repair Replace
-Bolts; loose, de formed, etc. OK Repair Replace
-Brackets/Hinges; bent, not rotating, etc. OK Repair Replace
Chains
-Chains; deforming, broken/bent links OK Repair Replace
-Hardware; Quick links OK Repair Replace
Sliding Components; AAG (IF APPLICABLE)
-Lubrication OK Repair