Triton Andrew User manual

19
21
530
60
43
124
430
145
174
Installers please note these InstructIons are to be left wIth the user
2180535B December 2007
Installation Instructions
ANDREW
Riser rail assembly
UNBMXFIXBT
p41502 andrew

B
A
B
A
B
A
B
A
Groove at
bottom
Lower bracket
B
A
Decide on the position of the riser rail on the
wall within the shower area. Proceed as follows:
Position the lower bracket to the wall and mark
fixing hole ‘A’. Make sure to position the bracket
correctly with the groove towards the bottom of
the bracket (fig.1).
Drill and plug the wall. (The wall plugs provided
are suitable for most brick walls — use an
appropriate masonry drill, but if the wall is
plasterboard or a soft building block, you must use
suitable wall plugs and an appropriate drill bit).
Note: That the holes are elongated at the back
of the bracket to allow for a small amount of
adjustment.
Locate the riser rail and lower bracket to the
wall and fix temporarily using the long screw
provided. Fit the upper bracket to the riser rail,
making sure to position the bracket with the
groove uppermost. Align the holes in the riser
rail and upper bracket.
With the upper bracket in place, align vertically
the rail and mark fixing position 'A' (fig.2).
Remove the rail assembly. Drill and plug the wall.
Screw temporarily both brackets to the wall. To
check the brackets are aligned, place the riser rail
into the curved recess of both brackets (fig.3).
Remove the rail, mark the two remaining fixing
holes ‘B’ and drill and plug the wall.
Fix the brackets to the wall using the short
screws in hole ‘B’.
Slide the showerhead holder onto the riser rail.
For the correct facing of the showerhead holder
make sure that the holes align and the lever is
facing forwards. Secure the holder to the rail by
turning the lever anti-clockwise. When tight, the
lever should face down (fig.4).
ANDREW RISER RAIL ASSEMBLY
WARNING!
Check there are no hidden cables or
pipes before drilling holes for wall
plugs. Use great care when using
power tools near water. The use of
a residual current device (RCD) is
recommended.
Tapered
thin end
at top
Lever facing
down
Fig.1
Fig.4
Groove at top
Upper bracket
B
A
B
A
Fig.2
Fig.3
Upper bracket Lower bracket

Washers
Shower
Showerhead
Showerhead
Holder
Slide the soap dish and hose retainer onto the
riser rail, below the showerhead holder (fig.5).
Locate the riser rail assembly to the upper
bracket. Align the upper hole in the riser rail with
hole ‘A’ in the bracket and secure using one of
the long screws supplied (fig.6).
Align the bottom hole in the riser rail with hole
‘A’ in the lower bracket and secure.
Fit the bracket trims over each end of the riser
rail, locating the runner into the groove before
sliding onto the bracket (fig.7).
Push fit the rail end trims into each end of the
riser rail.
FITTING THE HOSE AND
SHOWERHEAD
Feed the flexible hose (fig.8) through the
retaining ring (Water Regulations).
Screw the flexible hose to the shower outlet
and showerhead, making sure the supplied
washers are in place at both ends of the flexible
hose (fig.9).
Place the showerhead into the holder and
check that it fits correctly (fig.10).
Note: The holder is slightly tapered and the
showerhead and hose will only fit from one
direction.
IMPORTANT: It is the conical end of the
hose which grips into the holder. The
showerhead will not fit in the holder without
the hose attached.
ANDREW RISER RAIL ASSEMBLY
Fig.5
Fig.8
Fig.9 Fig.10
A
Fig.7
Fig.6

Ref. Description Spares No.
−Kit (without riser rail) 88900007
1. Bracket & trim 83309680
2. Riser rail 88800007
3. Showerhead holder 83309490
4. Soap dish 83308370
5. Hose retaining ring 83308380
– Flexible hoses available in the following
sizes:
1.00 m in white, chrome and gold
1.25 m in white, chrome and gold
1.75 m in chrome only
SPARE PARTS
Please refer to shower installation and operating instructions for service details
1
2
3
4
5