TrolMaster TS-1 User manual

TS-1
Thermostat Station
For Hydro-X Control System
Overview
Thank you for purchasing TrolMaster’s TS-1 Thermostat Station
for use with the Hydro-X master controller. It is specifically designed
to replace the traditional thermostat to control Commercial AC
units.
Features
No Extra Power Needed
LCD Display, Easy Operation
Micro-SD slot for Firmware Upgrades
Seamless Connectivity with Hydro-X
Replace Thermostat to Control Commercial AC Units
Connect the TS-1 to where your thermostat is on the wall using
preexisting RWYG wires, now you can use the TS-1 in conjunction
with the Hydro-X to control commercial AC units easily. Choose
your desired temperature setpoints for the Day / Night mode
(seeTemperature Settings in Hydro-X’s instructions), the TS-1
will turn on/off Cooling Mode or Heating Mode automatically for
the connected AC units based on that setpoint.
There is no need to provide power supply for the TS-1 unit.
It can be connected to the Hydro-X with a simple RJ12 cable. After
power-on, the Hydro-X will send the control data to the TS-1
automatically. The LCD screen of the TS-1 will display the
temperature setpoint (upper part ) and current temperature
(lower part
). When the current measured temperature is beyond
the setpoints, the TS-1 unit will control the commercial AC units
to perform cooling mode (Cool On) or heating mode (Heat On)
automatically.

FAN Button
Addressing Button
RJ12 Cable Socket
Micro SD Slot
Installation
Pull the 2 tabs outward to release the bracket from the unit, mount
the bracket to wall or surface near the thermostat cable, which
consists of 4-color signal wires (Red, White, Yellow and Green).
Peel off the outer sheath of all wires to reveal the copper wire.
Then, insert each bare wire into the corresponding terminal
insertion hole (R, W, Y, G) on the back panel while pressing the
bump near the terminal designation at the same time. Release
the bump to clamp the wire in each terminal hole. Verify the wire
head is firmly secured by gently pulling on the wire. Finally, place
the unit back on the bracket and press the 2 tabs back in to lock
the unit in place.
RWYG
Signal Wires

Operation Instructions
1. Connection to Hydro-X
After the signal wires are successfully connected to the TS-1
unit, connect the TS-1 to the Hydro-X with a RJ12 cable through
the DEVICES port on the bottom of Hydro-X. See below
connection diagram for reference.
After power-on, the LCD screen of TS-1 will show “Please
press Addressing Key” when the TS-1 is connected correctly.
Otherwise, it will show “Offline” when the TS-1 is connected
incorrectly.
Please press
Addressing
Key
Please press
Addressing
Key
Station T2
has been added
Offline
Correct Connection Incorrect Connection
2. Address Assignment
Press the Addressing button on the TS-1 unit so that the Hydro-X
will assign an address such as "T2" to the TS-1 unit accordingly.
The LCD screen of Hydro-X will display “Station T2 has been
added”. T2 is not the constant address code, it can be T1, T3 or
T4 depending on the connection sequence of the temperature
devices. The first one is marked as T1, the second one as T2, and
so on.
You can also check the address code on the Hydro-X as shown
below:
A
Main Menu of Hydro-X
LCD Screen of TS-1 LCD Screen of Hydro-X
Left Button Devices Status of Hydro-X

3. FAN Setting
Press FAN button to select ON or AUTO mode (toggle to reselect)
for the fan inside an air-conditioner.
AUTO: Fan runs only when the heating or cooling mode is on
(Auto is the most commonly used setting).
ON: Fan is always on.
NOTE: Options may vary depending on your heating/cooling
equipment.
Setpoint
Cool
On On
Current
40F
72F
Setpoint
Heat
On Auto
Current
77F
71F
ON Mode （FAN）
AUTO Mode（FAN)
Setpoint
Cool
On On
Current
40F
72F
Setpoint
Heat
On Auto
Current
77F
71F
Cooling Mode
Heating Mode
4. Cooling / Heating Mode
After power-on, the LCD screen of TS-1 unit will display the
setting temperature (setpoint) and current temperature. The
TS-1 will turn on/off Cooling Mode or Heating Mode automatically
depending on the variance between current temperature and
setpoint. For example, when the current temperature is HIGHER
than the setpoint, the TS-1 will start cooling mode and display
“Cool On” on the screen. When the current temperature is
LOWER than the setpoint, the TS-1 will start heating mode and
display “Heat On” on the screen.

5. Firmware Upgrade
Press and hold “Addressing”button while replugging the RJ12
cable, the upgrade process will be done automatically.
Keep hold Key
to enter
update nenu
Setpoint
Cool
On On
Current
40F
72F
*NOTE:Make sure the file name of firmware upgrade should be
named as “ts1_update.hex”.