Tru audio T100 User manual

User Manual - T100

2-CHANNEL AMPLIFIER

Description

The T100 was designed to be a cost-effective way to add audio to any home. Using the latest digital technology,

the T100 is able to run much cooler than a standard class AB amplifier, meaning it can be placed in almost any

dry location. We also added two convenience features: 1) a subwoofer RCA out and 2) a mono switch so you can

play both channels of music in full range from all speakers.

Features

Box Contents

• T100 • IR Receiver • Remote Control

• Power cord • (2) Mounting brackets • User Manual

32 4 5 6 7 8 9 101

1. Power cord

2. 120V - 240V A/C switch

3. Power switch

4. IR input connector (IR Receiver included)

5. Audio line out (3.5mm)

6. Dip switches

1. Fixed or Variable

2. IR Set or IR Learn

3. Mono or stereo

4. Full range or above 80Hz: crossover setting for the speaker output

5. Analog RCA (”IN 1”) or digital Toslink (”IN 2”): default input

6. Service mode - Must Remain OFF

7. Analog RCA input

8. Digital (Toslink) input

9. Subwoofer Out

10. Speaker connection

Dip Switches

1. Fixed - The amplifier output volume is fixed at 95%.

Variable - The amplifier output volume can be adjusted via IR remote.

2. IR Set - This will allow you to use the remote (through the IR receiver) to control the T100.

IR Learn - For learning IR commands from your remote (off, on, mute, volume down & volume up).

3. Mono - All speakers play both left & right channels of audio (full range).

Stereo - each speaker will play its own left or right channel of audio.

4. FULL - The full range of audio frequencies will be outputted through the speakers (20 Hz - 20 kHz).

HP 80 Hz - The internal crossover limits all frequencies below 80Hz, going to the speakers.

5. IN 1, IN 2 - If the T100 loses power or if the hard power switch is turned off, the amplifier will default to the

input set by the dip switch when power is restored.

6. SERVICE MODE - Service mode is not used. Leave dip switch set to “off”

SWITCH POSITION

UP FIXED IR SET

IR LEARN

STEREO

MONO

FULL

HP 80Hz

IN 1 ON

OFF

IN 2VARIABLE

1 2 3 4 5 SERVICE

MODE

DOWN

Installation

Connecting the T100 to a TV with Subwoofer

1. Connect the TV audio to the T100 using analog RCA cables or Toslink

2. Set dip switch 5 according to the audio source

3. Set dip switch 1 to the down position (variable) for volume to be controlled by the T100 remote

or set dip switch 1 to the up position (fixed) for volume to be controlled by the TV

4. Connect an RCA cable from the powered subwoofer to the T100 “Sub out”

a. Set the subwoofer crossover and volume on the subwoofer

5. Connect the speakers

SUBWOOFER

IR RECEIVER

TELEVISION

SOUNDBAR

6. Connect the IR receiver to the “IR IN” and place the IR receiver somewhere in front of the TV where

it will be visible to the remote

NOTE: If using a Toslink from the TV to the amp T100 and you don’t hear audio, or the audio is garbled then set

the audio coming from the TV or cable box to PCM stereo.

Connecting the T100 to an Audio Source with Subwoofer

1. Connect your audio source to the T100 using an RCA cable or Toslink

2. Set dip switch 5 to IN1 or IN2 to set the default input

3. Set dip switch 1 to (variable) for volume to be controlled by the T100 remote, or, set dip switch 1 to

(fixed) for volume to be controlled by the audio source.

4. Connect an RCA cable from the powered subwoofer to the T100 SUB OUT. Set the subwoofer

crossover and volume on the subwoofer.

5. Now connect the speaker wires to the amplifier speaker output.

NOTE: To switch between audio sources, press the IN1 or IN2 button on the supplied remote.

OUT IN

Optional second

audio source

Linking Multiple T100

When linking multiple T100’s together the first T100 will be the control unit. Set the first amp to “variable”and

additional amplifiers must be set to “fixed”. The first T100 will control the volume of all additional amplifiers.

3.5mm to L/R RCA cable

IR Receiver

To additional amplifiers

Bridge Mode

Bridge mode combines both the left and right channels to a single channel mono signal output. Bridge mode is

stable down to a minimum load of 8Ω.

Power output bridged:

275W @ 8Ω

IR Connection, Control and Learning

Learning

This amplifier can learn the following commands (off, on, mute, volume down & volume up) from a TVs IR remote.

The IR receiver can receive a signal to about 15-20 feet away.

TREBLE

Remote

8Ω LOAD

8Ω

SIGNAL

RECEIVING ZONE

IR RECEIVER

TOP VIEW

SIGNAL

RECEIVING ZONE

IR RECEIVER

FRONT VIEW

How to learn the IR codes:

SET UP

1. Plug the IR receiver into the T100

2. T100 power switch must be OFF

3. Dip switch #2 must be set to IR SET

PROGRAMMING

1. Hard power the T100 on

2. Set dip switch #2 to LEARN (light will flash blue)

3. Aim the remote you want to use at the IR receiver (TV, cable, etc.)

4. Push the first button in the sequence (power off), blue light will flash, wait one second and press the

same button again. The light will flash purple to confirm code.

5. Repeat learning for power on, mute, volume down and volume up.

6. After last button is programmed the blue light will stay on or turn red if no audio source is plugged into

the T100.

7. Set dip switch #2 up to IR SET

8. You are now programmed.

*When learning IR commands, the T100 will always learn in the following order.*

Programming sequence:

• Power off

• Power on

• Mute

• Volume down

• Volume up

IR Reset. When learning the IR codes, if a mistake happens, you can set dip switch #2 to IR SET to

reset the learning process and start again.

NOTE: Learn function will stop after 30 seconds of no activity.

It is the policy of TRUAUDIO to continuously incorporate improvements into our products. All specifications are subject to

change without notice. If you have any questions regarding this or any other TRUAUDIO products, please visit

www.TruAudio.com or contact us:

Office: 1-888-858-1555, Monday-Friday 7 am - 6 pm MST.

Email: [email protected]

TruAudio

198 N Old Highway 91

Hurricane, UT 84737 USA

SoundVision Technologies dba TRUAUDIO

SUBWOOFER and ELECTRONIC PRODUCT WARRANTY

All subwoofers and amplifiers have a limited 5 year warranty. This warranty includes 5 year parts and repair labor on all

components. The warranty extends only to the original purchaser of the product and not to any subsequent owner. TRUAUDIO’s

obligation under these warranties is limited to repairing or replacing any component found defective in material or workmanship

under normal conditions of use with an equal and/or current product. These warranties shall not apply to products which have been

abused, modified, or disassembled. Products to be repaired or returned under this warranty must be returned to the factory

through an authorized TruAudio dealer with all transportation and insurance charges prepaid.

Never expose the amplifier to any kind of moisture. This product should not be used outdoors, near bathtubs, sinks, wet basements or swimming

pools. This product is meant for indoor use only. Avoid placing this amplifier near heat sources such as radiators, heat registers or stoves. This

amplifier should not be used in direct sunlight. Before connecting any cables to the amplifier, the power switch must be in the OFF position. Locate the

amplifier where there is adequate ventilation to the sides of the amplifier. If the amplifier is used in a cabinet an additional cooling fan might be

necessary. Make sure that the speakers that will be connected to this amplifier can handle the output power from the amplifier. Do not use this amplifier