TruSens N-300 User manual

OWNER’S MANUAL
HUMIDIFIER
N-300

CONTENTS
SAFETY INFORMATION
FEATURE HIGHLIGHTS
PRODUCT OVERVIEW
GETTING STARTED
CONTROL PANEL
SENSORPOD
SPECIFICATIONS
AROMATHERAPY
REPLACING THE WATER FILTER
CARE & MAINTENANCE
FAQ & TROUBLESHOOTING
WARRANTY & SUPPORT
4
6
7
8
10
11
12
13
14
15
17
19
Welcome to comfortable indoor air with
TruSens. Thank you for allowing us to join
you on your journey towards wellness.

54
SAFETY INFORMATION
WARNING: The water and heater may cause burns.
Unplug the humidifier and let cool before cleaning.
WARNING: Skin or eye damage may result from directly
viewing the light produced by the lamp in the apparatus.
This appliance contains a UV-C bulb.Avoid exposing the eyes and
skin to UVC radiation as it may cause eye and skin injury.
• This appliance contains an UVC emitter.
• Unintended use of the appliance or damage to the housing may
result in the exposure of UVC radiation.
• UVC radiation may cause eye and skin irritation.
• Avoid exposing eyes and skin to UVC radiation.
FIRST AID INSTRUCTIONS - Seek medical attention in event of injury.
The use of this device is a supplement to and not a substitute for
standard infection control practices; users must continue to follow all
current infection control practices, including those practices related
to cleaning and disinfection of environmental surfaces.
CONFORMITY INFORMATION
EPA Est. No. 97661-CHN-1
Sensor: FCC ID: GV3-21SP0H1 IC: 6128A-21SP0H1
www.trusens.com
This device complies with Part 18 of the FCC rules. This device
complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation. This equipment
has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
Modifications: Any modifications made to this device that are not
approved by ACCO Brands may void the authority granted by the
user by the FCC and/or Industry Canada to operate this equipment.
CAN ICES-003(B)/NMB-003(B)
This device complies with Industry Canada RSS standard(s).
Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired
operation of the device.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
READ AND SAVE THESE INSTRUCTIONS / READ THE
LABEL AND ANY OPERATING MANUAL BEFORE USING
PRECAUTIONS
This appliance has a polarized plug (one blade is wider than
the other). To reduce the risk of electric shock, this plug
is intended to fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician. Do not attempt
to defeat this safety feature. Unplug or disconnect the
appliance from the power supply before cleaning the base.
WARNING: To reduce the risk of fire or electric shock,
do not use this appliance with any solid-state speed control
device.
Do not operate any humidifier with a damaged cord or plug,
or if the wall socket is loose.
Do not run cord under carpeting, throw rugs, runners,
or similar coverings. Do not run cord under furniture or
appliances. Arrange cord away from traffic area and where it
will not be tripped over.
• Never handle the plug with wet hands.
• Do not touch the mist when in warm mist mode.
• Remove all packaging, including the filter bag, before use.
• Unplug the humidifier and empty the water tank before
moving. Always carry by the base.
• Always place the appliance on a dry, firm, flat surface that is
free from obstructions.
• Appliances that are obviously damaged must not be
operated.
• Do not pour water into the mist outlet or chimney.
• Always fill the water tank with clean, cold water. Do not
overfill the water tank.
• If you have concerns with your local water quality or if you
have especially hard water, use distilled water.
• Always place the water tank directly onto the base when
there is water in the tank.
• Do not add essential oils directly to the water tank. Do not
use synthetic fragrances.
• Always empty any water from the water tank before
cleaning or before replacing the filter.
• Locate humidifier near the outlet wall socket and do not
use extension cords.
• This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved.
• KEEP OUT OF THE REACH OF CHILDREN. Children shall
not play with the appliance.
• Do not attempt to service or repair this product yourself.
• Only use the humidifier with the power cable provided.
• Only clean this machine with a damp cloth, do not use
solvents or bleach.
• Do not place any part of the humidifier in a dishwasher.
• Do not submerge the base reservoir under water at any
time.
• Do not block or obstruct the mist outlet or chimney.
• Do not insert fingers or other items into the mist outlet or
chimney.
• Do not place foreign objects in the water tank or base
reservoir.
• When the humidifier is in standby mode the SensorPod is
still transmitting a signal/data.
• Let the appliance cool down before cleaning. Water spilled
from the appliance may be hot and a burn hazard.
• Replace any leaking batteries immediately. Remove the
batteries if the appliance is being stored for long periods.
• Safely dispose of or recycle used batteries per local
regulations.

76
FEATURE HIGHLIGHTS
SensorPod™
Remote humidity monitor with integrated remote-control functionality.
Water Soening Filter
Soens the water to help prevent the buildup of mineral scale.
UV-C Light
Top Fill Design
Lightweight water tank lid allows easy refilling and cleaning of
the large capacity water tank.
Warm & Cool Mist
Customize your comfort level with either warm or cool mist.
PRODUCT OVERVIEW
Carry handle
Mist outlet
Control panel
Water tank lid
Water level indicator window
Water tank
8L (2.1 gal)
Aromatherapy tray (back)
Base
Humidifier
FilterSensorPod™
Humidifier Controls
Battery Chamber
underneath
Informs and Adapts
Humidifier displays relative humidity percentage in real-time
and reacts to maintain your desired level of humidity in the room.

98
GETTING STARTED
1. Prepare the water filter
Remove plastic bag from filter. For optimal performance, submerge filter in bowl of water for 1 hour.
WARNING
Always unplug the humidifier before removing the water tank. Empty all water before cleaning
water tank, replacing filter or moving the humidifier. Only place the water tank on a hard, solid
surface; do not place on carpeting.
2. Install the water filter
a) Unscrew gray cap. b) Secure the filter onto gray cap. c) Tightly secure gray cap with filter onto water
tank until indicator meets lock symbol. Failure to properly tighten gray filter cap may result in leaking.
Return water tank on top of base.
4. Set up
Place humidifier on a dry, firm, flat surface that is free from obstructions.
Note: Failure to properly tighten gray filter cap may result in leaking.
Open lid of battery chamber found on SensorPod (bottom) and insert 2 AAA batteries (provided).*
SensorPod will automatically begin monitoring if humidifier is on.
For optimal results, place SensorPod on a tabletop or counter across the room, within line of sight of
the humidifier.
Control the humidifier with the touch buttons on SensorPod.
3. Fill the water tank
Remove water tank lid and fill with room temperature water (preferably distilled) with pitcher.
The light in the tank is blue when it contains sufficient water (tank is red when it needs refilling).
NOTE: When the base reservoir is completely
dry, like at the first use or at the start of each
new season, there may be a delay of up to 30
seconds before mist is produced.
*
WARNING: Do not pour water into the mist
outlet or directly into the base/reservoir. Do not
fill over the “Max” indicator line.
CAUTION: Heavy object. To avoid injury always
fill tank from the top and use care when liing.

1110
CONTROL PANEL SENSORPOD™
Warm Mist
When on, mist is warmed.
Timer Mode
Humidifier will automatically turn off aer 2, 4, 8, or 12
hours. To cancel this countdown, simply press button
until no timer setting is displayed.
Filter Change Indicator
Filter indicator glows red when it is time to be replaced.
To reset, simply hold the Filter Reset button for 3
seconds.
If you replace the filter before the indicator turns red,
simply hold the Filter Reset Button for 10 seconds to
notify the humidifier that a new filter has been installed.
Target Humidity
Press the – or + button to set your own target humidity
between 40 - 60%. The humidity level will be displayed
as a percentage on panel (i.e. 45 = 45%).
Dimmer Mode
Display illumination turns off – for use while sleeping –
without sacrificing the effectiveness of the humidifier.
Simply press the button again to bring back all
display features.
Misting Speed Settings
Select misting speed (1/2/3) or AUTO mode. In
AUTO mode, humidifier will only produce mist when
SensorPod measures humidity lower than target
humidity setting. Default AUTO mode setting is 50%
relative humidity.
Power Button
Note: It will take a few minutes to achieve its full temperature.
(See page 14 for replacement instructions. Follow above Reset button
instructions aer replacing filter.)
Remote Control
The SensorPod reads the humidity level where it is placed. The battery
operated SensorPod should be positioned in line-of-sight of the humidifier;
up to 33' away.
The SensorPod is also a remote control for your humidifier. Power on and off,
adjust the misting speed, and dim the lights on the display.
The SensorPod communicates with the humidifier using radio frequency
signals and will be pre-paired on the production line and ready for use when
you open the box.
HUMIDITY
Humidifier Controls:
Power on/off
Misting Speed
Dimmer on/off
Battery Chamber

1312
Model N-300
Tank Capacity 8 Liters (2.1 gallons)
Max Mist Output 300 ml/h (cool)
Operating Time 26 - 80 hours
Room Size Up to 485 sq.  / 45 m sq.
Sensor SensorPod™, works up to 33  (10m) from humidifier
Misting Speed Settings 1, 2, 3, AUTO
Timer Settings 2, 4, 8, 12 hr
Warm Mist 104˚ F (40˚ C) at atomizer
Empty Tank Indicator Water tank LED turns red
Filter Change Indicator Yes
Noise Level 41.0 dB Max
Dimensions Ø 8.8" x 22.8" (Ø 224 x 578mm)
Weight (empty) 7.3 lbs (3.3 kg) with filter
Power Requirements 100 - 130V / 60 Hz
Power Consumption 16 - 67.2W / 128 - 182.4W (warm)
Warranty 3 years
SPECIFICATIONS
Replacement Filter & Pads
Water Soening Filter WSF300-01 1 pack Replace aer 4 months (with normal use)
Aromatherapy Pads ATP300-01 10 pack Replace as needed
AROMATHERAPY
The humidifier includes an aromatherapy drawer, at the back of the unit, that
allows you to add your favorite essential oils for an enhanced experience.
WARNING
Do not use any synthetic fragrances - only use 100% natural essential oils. Do
not add essential oils directly into the water tank.
Adding Essential Oils
Open the aroma drawer on the back of the humidifier & apply 2-3 drops of
essential oil to the aroma pad (Fig. A).
When you are ready to replace the aroma pad, gently remove the pad from the
aroma drawer, and replace with a new pad making sure to secure the pad using
the tabs (Fig. B).
Refer to page 12 for aromatherapy pad replacement part number.
Fig. A Fig. B

1514
The filter indicator will glow red when it is time to change
the ion exchange filter.
Note: The filter should also be replaced aer the humidifier has been
stored away for a season or more.
WARNING: Always unplug the humidifier before
removing the water tank. Always empty any water
from the tank before replacing the filter.
Note: Remember to submerge the replacement water filter in a bowl of
water for 1 hour before using (Fig. C).
Accessing the filter
1. Remove the water tank from its base, pour out any water
into a sink and gently place on its side so that the gray
filter cap is exposed and accessible.
2. Turn the gray cap counter-clockwise to remove the filter
from the water tank (Fig. D).
3. Remove current filter from gray cap in a counter-
clockwise motion (Fig. E). Secure replacement filter
onto gray cap threading in a clockwise motion (Fig. F).
4. Tightly secure gray cap with filter onto the threading
on the bottom of the water tank and turn clockwise until
indicator meets lock symbol (Fig. G).
5. Return water tank on top of base, plug-in and power on
your humidifier. Hold the Filter Reset Button until the
red indicator turns off.
Refer to page 12 for water soening filter replacement part number.
REGULAR MAINTENANCE
Cleaning the tank and base reservoir on a regular basis is critical to
ensure the optimal performance of the humidifier. The water filter will
help to prevent mineral scale buildup, but a regular cleaning routine
is important for addressing mineral scale in areas with especially hard
water, as well as to prevent any odors that may be caused by standing
water if the humidifier is not used for days at a time.
If you have concerns about your local water quality or if you have
especially hard water, we recommend using distilled water.
WARNING: Always unplug the humidifier before removing the water
tank. Always empty any water from the tank before cleaning. Always
allow any remaining water in reservoir to cool before cleaning.
We recommend that the following is carried out when you refill the
water tank:
1. Rinse the water tank with water and wipe clean.
2. Dry with clean cloth.
Note: Lower humidity control settings or turn off the humidifier if moisture forms on
wall or windows
WARNING: Do not use any detergents or cleaning chemicals.
Do not place any part of the humidifier in a dishwasher.
Do not submerge the base reservoir under water at any time.
REPLACING THE WATER FILTER
Fig. C
Fig. D
Fig. E Fig. F
Fig. G
CARE & MAINTENANCE

1716
Where do I place the SensorPod™?Anywhere you want to measure the humidity within the room.
For optimal results, place the SensorPod™up to 33ft (10 m) away from the
humidifier on a counter or table, within line of sight of the humidifier. In Auto
Mode, the humidifier will work to distribute humidity until the SensorPod
reads an acceptable level.
How oen do I need to change the
filter?
That’s easy! The humidifier’s replacement indicator will notify you when it is
time to replace the water soening filter. Plan on replacing the water filter
every 3-4 months, with normal use of 8 hours per day and average hardness
of water.
How oen do I need to replace the
aromatherapy pad?
The humidifier comes with one aroma pad. Replace as needed.
Humidifier won’t turn on. Check that the power cord is connected securely to both the wall outlet
and the humidifier. Check if there is a power outage in the outlet by trying a
nearby light or device, or by trying a working device in the same outlet.
Check that there is water in the tank, and consider filling the tank to the
“Max” indicator line.
Please contact us if you’re still having a problem (page 19).
FAQ & TROUBLESHOOTING
WEEKLY MAINTENANCE
MAINTENANCE BEFORE STORING
Water Tank
1. Empty all water out of the tank.
2. Remove filter from tank, and tightly secure the gray cap onto the tank.
3. Add 2 cups of distilled white vinegar and 2 cups of water to the tank.
4. Gently shake the water tank to coat the inner sides of the tank.
5. Allow the vinegar and water to soak inside the tank for 30 minutes.
6. Dampen a so cloth with undiluted white vinegar and wipe
thoroughly around the tank and the outside of the filter.
7. Rinse with clean warm water to remove the mineral scale and vinegar.
8. Dry with clean cloth.
Base Reservoir
1. Empty the water by pouring out the le side of the base, to avoid
splashing onto control panel or power cord inlet.
2. Remove the covers of the UV-C chamber and PTC heater.
3. Pour 20 fl oz cup of distilled white vinegar into the reservoir, making
sure that the atomizer, UV-C chamber and PTC heater are submerged
in vinegar. Allow the vinegar to soak for 30 minutes, and then carefully
empty the vinegar by pouring out of the le side of the base.
4. Dampen a so cloth with undiluted white vinegar and gently wipe the
reservoir, including all components.
5. Rinse thoroughly with clean water and dry with a clean cloth.
Follow weekly maintenance instructions above. Let the humidifier dry completely
before storing. Do not store with water inside the tank or base reservoir. Store in a
cool dry place. Clean the humidifier before the next season begins.
UV-C
chamber
Atomizer
PTC heater

1918
Pairing SensorPod™and Humidifier
The SensorPod communicates with the humidifier
using radio frequency signals, and is already paired
and ready for use when you open the box. In the rare
event that the signal is interrupted, the humidifier’s
sensor indicator light will blink. You can repair the
connection in just a few easy steps.
1. HOLD the Power Button on the humidifier for 3
seconds, until you should hear two chimes.
2. HOLD the Power Button on the SensorPod remote
control panel for 5-7 seconds.
3. The connection is established when the humidifier’s
sensor indicator light is lit with no blinking, and the
humidity display turns on.
Humidifier won’t go into Auto
Mode.
OR
Humidity indicators are off.
OR
Humidifier’s sensor signal indicator
is blinking.
First, check that the SensorPod is within range of the humidifier (up to
33/10m).
Next, check the SensorPod batteries and consider replacing with new
batteries.
If the connection is still failing, see below instructions on repairing the
SensorPod’s connection.
I’ve lost my SensorPod™!Don’t worry! Please contact our customer support team and you can order
a replacement SensorPod. Follow the easy pairing instructions below to pair
your replacement SensorPod with your existing humidifier!
FAQ & TROUBLESHOOTING WARRANTY
TruSens™ warrants that the machine will be perform to the specifications stated and be free from
defects in materials and workmanship for a period of 3 years from date of purchase, subject to
normal use. Within the guarantee period, TruSens will at its own discretion either repair or replace
the defective machine free of charge. Defects due to shipping, misuse, improper maintenance or
the use of any parts from another manufacturer are not covered under this guarantee. Proof of date
of purchase will be required. Repairs or alternations made by persons not authorized by TruSens will
invalidate the guarantee. This guarantee does not affect the legal rights which consumers have under
applicable national legislation governing the sale of goods.
SUPPORT
Thank you for welcoming TruSens into your home. Our customers are
at the heart of what we do, and we strive to design products that fit
your lifestyle. If you have any questions or feedback, please reach out!
Visit our website at www.trusens.com
Email us at [email protected]
Call us at 1-833-TRUSENS (1-833-878-7367)
& Follow us @TruSensWellness
Subscribe to our YouTube channel TruSens

©2022 ACCO Brands. All rights reserved. TruSens™, U™ &
Design, and SensorPod™ are trademarks of ACCO Brands.
ACCO Brands
101 O’Neil Road
Sidney, NY 13838
Tel: 1-833-TRUSENS
(1-833-878-7367)
www.trusens.com