Twister Display Easy Dunker User manual

To Order Call: 1-800-637-3656
Easy Dunker
Initial Assembly Instructions
1. Remove all packing, and remove unit from pallet. NOTE: Trailer
and tank are one unit, do not try to separate!
2. Remove cage from front of tank. Turn cage over and line the holes in
the cage with the holes
along the top of the
tank. Drop a
1/4”carriage bolt
through each hole.
Then put on a flat
washer, lock washer,
and nut and tighten
down. NOTE: Start at
one end of the cage
and work your way
around to the other
end.
3. Place the unit on a
level surface. Put the wing perpendicular to the dunk tank (extending
from the side of the frame.) There are two brackets on the side of the
wing. Loosen the bottom one only so that it can be moved up and down
the pipe.
4. Protruding from the side of the frame are two posts (one pointing up
and one pointing down). Insert the top one into the top wing bracket.
(You will need to lift the tank slightly.) Drop the bottom bracket onto the
bottom post. Make sure that the wing is in line with the frame, then
tighten the bottom bracket.
5. Use the ball bungees to secure canvas to the wing.
6. Place the arm into the trigger mechanism. Make sure the
pivot point in the arm drops into the hole on the side of the frame. Insert
the end of the arm through the hole in the canvas. Insert the target into
the end of the arm and rotate it clockwise until the target is tightened into
the arm. NOTE: Do not over tighten the target. Just tighten until
snug.
Cage Wing
Target
www.twisterdisplay.com
Wear shoes, keep hands on knees,
and sit forward.
Move towards the front of the tank when
coming up out of the water to avoid hitting
head on the seat.

To Order Call: 1-800-637-3656
Easy Dunker
Safety Rules
1. Keep Easy Dunker away from electricity.
2. Keep water level filled to at least 8" from top of
tank.
3. Never leave a filled Dunk Tank unattended by an
adult.
4. When tank is unattended, always drain water.
5. Keep all non-swimmers and anyone less than 5' tall
out of tank.
6. To keep from slipping, always wear tennis shoes.
7. Advise dunkee to move towards the front of the tank
when coming up out of the water to avoid hitting
head on the seat.
8. Only one person at a time allowed on the seat or in
the tank.
9. Never use baseballs or other hard balls.
10. Never stand on seat.
11. When sitting on the seat, keep hands on knees and sit
forward.
12. Do not hit target with hands.
13. Do not operate the Easy Dunker during a storm.
14. Periodically, check tank and trailer frame for sharp
edges.
When towing…
15. Tie a second safety rope to hold wing frame against tank.
16. Always use a safety chain and BOTH tongue pins.
17. Check brake lights and turn signals.
www.twisterdisplay.com
Easy Dunker
Initial Assembly Instructions Continued
7. Place one hand on the front of the seat and push down.
With the other hand “test” the target to see that it works
properly.
8. Slowly tilt tank onto its wheels. As you face the bottom of
the tank place the tail-light marked “road side” next to the
left side light bracket, and place the light marked “curb side”
next to the right side light bracket. Pull out enough cable so
that the plug will just reach the bottom of the tank. Run the
light cord along the bottom of the trailer frame taping or
tying it to the underside of the frame.
9. Run the yellow/brown cord to the “road side” (left)
bracket and feed it through the hole in the bracket. Run the
green/brown cord to the “curb side” (right) bracket and feed
it through the hole in that bracket. Cut of the excess cable on
both sides and strip about a 1/4” of insulation off the ends.
Insert the ends of cable into their respective holes in the back
of the light units. (The white cable can be used for grounding
purposes.)
10. Using the nuts included in the light kit attach lights to
the brackets. Using electrical tape or zip ties, attach the light
cable extension to the tongue. It should extend a couple of
feet past the hitch to allow enough slack for turns and the
other end should stop about halfway down the length of the
tongue where it would meet the light cable plug on the tank
frame when the tongue is in place.(After the trailer is hooked
up to a vehicle, be sure to test the turn signals and brake
lights before towing.)

To Order Call: 1-800-637-3656
Easy Dunker
Instructions
To Tow
1. Fold wing in against the side of the unit and securely tie off.
Then slowly tilt tank back onto its wheels. Place seat in its “up”
position and lock.
2. Insert hitch tongue and use both pins to secure it.
3. Attach trailer to vehicle. Put pin or bolt through hitch release
lever and secure. Attach safety chain to vehicle. NOTE: Always
use the safety chain when towing.
4. Hook up lights to tow vehicle, and be sure to test the turn signals
and brake lights before towing.
5. Place target, target arm, and balls safely in tow vehicle.
Set Up
1. Select a level area for set up.
2. Unhook trailer and lights from tow vehicle and roll to set up area.
(NOTE: Trailer and tank are one unit, do not try to
separate!)
3. Raise tongue end of trailer and remove hitch pins from tongue
bar. Slide tongue bar out and replace pins in bar.
4. Slowly lift up and set tank upright. (Be careful not to drop tank
onto its bottom.)
5. Untie rope holding the wing against the tank. Swing wing out
into position. NOTE: The wing MUST BE STRAIGHT out
from the tank frame. If it is at an angle the trigger will not work
properly.
6. Lower the stabilizing rod on the bottom of the wing so the wind
does not move it as this will cause the target arm to jam.
7. Check drain plug to make sure it is tight and then fill tank to the
top with water (approx. 500 gallons).
8. Make sure the pivot point in the arm drops into the hole on the
side of the frame. Insert the end of the arm through the hole in the
canvas. Insert the target into the end of the arm and rotate it
clockwise until the target is tightened into the arm. NOTE: do
not over tighten the target. Just tighten until snug.
9. Place one hand on the front of the seat and push down. With the
other hand “test” the target to see that it works properly.
www.twisterdisplay.com
Easy Dunker
Instructions Continued
Operation
1. Check to see that seat is properly locked and is released
when the target is pressed. Be sure to show this operation
to the person who will be on the tank as they will need to
know how to reset the seat and trigger mechanism each
time it is released, before they get back onto the seat.
Please remind the dunkee to keep their hands on their
knees and sit forward on the seat.
2. Use ONLY the balls that came with the Easy Dunker.
3. Monitor water level to keep it full.
Take Down
1. As soon as you are finished using the dunker, open the
drain and let the tank empty.
2. Fold wing in against the side of the unit and securely tie
off. When towing Easy Dunker, tie a second safety
rope to hold wing frame against tank. Then slowly tilt
tank back onto its wheels.
3. Place seat in its “up” position and lock.
4. Insert hitch tongue and use both pins to secure it.
5. Attach trailer to vehicle. Put pin or bolt through hitch
release lever and secure. Attach safety chain to vehicle.
6. Hook up lights to tow vehicle, and be sure to test the turn
signals and brake lights before towing.
7. Place target, target arm, and balls safely in tow vehicle.