Twister Display SLIME MACHINE Installation instructions

Base Unit: Quantity-1
Tires (with 5/8 bolts
and lock nuts):
Quantity-2
Tri er Unit:
Quantity-1
Bucket Assembly:
Quantity-1
Collar: Quantity-1
Corner Fittin :
Quantity-3
24” Pipe: Quantity-1
44.5” Tapered Pipe: Quantity-4
41.5” Pipe: Quantity-6
Tar et Cross Brace: Quantity-1
Filler Tube Hook:
Quantity-1
Tar et Arm: Quantity-1

Filler Tube
Clips:
Quantity-4
Tar et: Quantity-1
Filler Tube:
Quantity-1
Spon e Balls:
Quantity-12
Drum Pump: Quantity-1
Drum: Quantity-1
Vinyl Canvas:
Quantity-1
Guar Gum:
Quantity-8
(8 ounce ba s)
Green/Yellow Food Dye:
Quantity-8
(16 ounce bottles)

Attach tires to the base unit, with the
5/8” bolt and lock nut. (The nut goes on
the inside side of the tire.)
Insert a 44.5” tapered pipe in each cor-
ner fitting of the base unit. (The tapered
end goes up.)

Put the target arm cross brace onto two
of the tapered pipes.
IMPORTANT NOTE: The arm pivot
goes on the inside and is on the
opposite side from the wheels.
Insert a 41.5” pipe onto each tapered
pipe .

Slide the bucket assembly onto the
trigger unit. Make sure that it is posi-
tioned so that the roller engages with
the trigger hook.
Slide on the collar and tighten.
Slide on a corner fitting and
tighten.
Insert the remaining 41.5” pipes in-
to the corner fitting and tighten.
Place the remaining two corner fit-
tings onto either end of the 24”
pipe. Be sure to slide them com-
pletely on, but do not tighten. At-
tached these corner fittings to the
opposite ends of the 41.5” pipes.
(Leaving the corner fittings loose
will help to guide them onto the
pipes.) Tighten all fittings.
Tip the unit onto its side. Block
the tires and find items to elevate
the unit about a foot or so. Place
the top on the unit, and tighten.

Insert filler tube hook and tighten.
Attach filler tube.
Use the clips to route
the filler tube along
the frame to where
ever you are going to
place the drum.
Attach the canvas to
the frame with the
Velcro straps.
Insert the pump in-
to the bung on the
drum. The connect
the filler tube to
the pump.
The drum can be at-
tached to the base
using the ratchet
strap.

Create a fine mist with a
garden hose sprayer.
VERY SLOWLY sprinkle
about half of the guar gum
into the mist.
Once the drum is half filled
(and the guar gum half
used), stop and stir thor-
oughly. NOTE: A cordless
drill with a mixing attach-
ment works perfectly for
this.
Continue spraying the water
and sprinkle the remainder
of the guar gum into the
mist.
Add 6-8 caps full of green
food dye and mix. NOTE:
The food dye is undiluted
and will stain.

Fill the drum with water, then
add 6-8 caps full of green
food dye and mix. NOTE:
The food dye is undiluted
and will stain.
NOTE: A cordless drill with a
mixing attachment works
perfectly for this.

♦ Never use baseballs or hard balls. (Use only
the balls provided.)
♦ Set up on level round.
♦ Keep Slime Machine staked and/or sand-
ba ed for stability.
♦ Keep Slime Machine away from electricity.
♦ Never stand under the bucket when in use.
♦ Do not allow anyone to climb on or lean
a ainst the Slime Machine.
♦ Do not allow anyone to hit the tar et with
their hand.
♦ Take down the Slime Machine if there is hi h
wind or chance of li htenin .