UAI SD600 User manual

Please read this manual carefully before installation and keep it for application
Outdoor Intelligent High Speed Dome Camera
User Manuel
V D3.31SHAN/2009

Accessories
Connection adopter
Ceiling mount bracket
Wall mount bracket
Corner mount bracketPole mount bracket
Joystick controller

Catalogue
Chapter 1 Product Introduction....................................................................1
Chapter 2 Specification..................................................................................3
Chapter 3 Connection & Setup.......................................................................4
Chapter 4 Protocol & Address Code Setting....................................................6
Chapter 5 User Manual of the Controller........................................................8
Chapter 6 Guide of OSD Menu Application...................................................10
Chapter 7 255 Channels Address DIP Swithch Diagram................19
Gudie of Camera Module OSD Menu..............................18

CHAPTER 1: Product Introduction
IR Intelligent high-speed dome camera is one high-tech surveillance & control product with high-reso
lution color camera module, omni-direction Pan/Tilt, infrared LED array,multi-functional decoder,CPU
processor and memory chip. The product reduces the connection between system components and the ins-
tallation process, it extremely improve the stability of the system. And it fits different environments no m-
atter indoor or outdoor.7 inch 's profile match with special install mount, arm bracket or ceiling mount can
be selected. This dome with weather-proof design, the housing adopts with PC material which is vandal-
proof,waterproof,aging resistance, anti-acid rain, high temperature resistant and anti-erode.
Characteristics:
Camera specification:
*The speed dome support different integrated camera module including SONY, SANYO.
Powerful Pan/Tilt function:
Preset, Pattern, Swing, Privacy mask, Group and more function
PTZ lens control
OSD Menu
Alarm Function
*Max. 360 /sec high speed Pan/Tilt turning
*Adopted with vector driving technology, Pan/Tilt motions are accomplished in the shortest path. As a re
sult, time to target is reduced dramatically and the video on the monitor is very natural to watch.
*Super slow speed function can be reached by joystick, the lowest speed can touch 0.05 /sec.
*Up to 128 pieces preset point can be memorized. The additional information such as dwell time,label ...
can be set as demand.
*Up to 8 pieces point-to-point auto scan can be memorized. Support proportional shift between zoom and
speed.
*Up to 2 of pattern can be recorded and played back. It can record 200 operation commands.
*Up to 5 pieces GROUP can be stored, the function enable the camera to move repetitively with combin-
ation of Preset or Pattern or Swing. A group contained with Max.10 presets, patterns or swings.
*Max.8 of Privacy masks can be located wherever it is required to protect private life. (Only Sony camera
module support this function)
*Support Schedule function.
*Max. 1024 cameras can be controlled at the same time by RS-485 bus communication.
*Pelco-D, Pelco- P protocol can be selected.
* The situation of camera can be displayed on screen with OSD menu function. The detailed camera func-
tion also can be set with OSD menu.
*The information of camera series number, Pan/Tilt position, alarm in/out, preset all can be shown on sc-
reen or not with OSD menu setup;
Built-in 4 channels input function.
If anyone alarm detector was activated then camera can auto move to preset that beforehand setup.
¡ã
¡ã
1
Product Introduction

*With built-in fan & heater and the weather-proof design, the product is very suitable for application in
outdoor environment.
*The structure of dome camera meets the demand of IP66 standard.
*The design concept of high-speed dome and mounting based on convenient installation.
Convenient installation and operation
Product Introduction
2
Product Diagram

CHAPTER 2: Specifications
2.1 Configuration of Speed Dome Camera
Product Photo Speed Dome Dimension
Specificaions
Scope
Preset
Manual
Swing Speed
Auto Scan
Fan/Heater
Power Supply
Temperature
Consumption
Heater Consumption
Pan/TiltOthers
Preset Quantity
Pattern
Swing
Group
Protocol
Moisture
OSD
<95 %
AC24V
20W
10W
Pelco-D; Pelco-P;VC;WORLD
Swing, Pattern, Group, Schedule... Functions.
Built-in auto controler heater and fan
-35°C~50°C
Programmable OSD for Pan/Tilt,Zoom camera,
Suport camera module setup and speed pan/tilt setup
128
2 Patterns,200 commands every one
8
5 Groups and each with 10 actions
Turning
Pan 360° ;Tilt 90°
0.025°~120°/Sec
360°/Sec
200°/Sec
15°/Sec~60°/Sec
Auto/Manual
Auto
Auto
ON/OFF selectable by OSD menu.
F1.6;f=3.9-85.8mm
0.1Lux
Yes
Yes
1/4" IT Exview HAD CCD SONY
480 lines
>48db
22 times optical zoom; 10 times digital zoom
Focus
I r i s
White Balance
BLC
Camera Type & Specifications
Camera
Sensor
Resolution
S/N
Zoom Ratio
Focal Length
Min. Illumination
Image Freeze
Day/Night
3

CHAPTER 3 Connection & Setup
3.1 Intelligent speed dome camera connection diagram
Connection & Setup
4
3.2 Cable connection;
Please check carefully the voltage and current capcity of the
electrical power source. The correct power to operate the camera is
AC24V / 1.5A;
There is one AC24V, 3A PSU in the packing carton of speed dome
camera. We suggest you to use this PSU to power supply the speed
dome camera. If the power is not enough, the camera can not work
properly.
The BNC connector can be connected to video coaxal cable
directly for vide signal transmission.
Please check the polarity of Rs485 cable before installation. If the
Rs485 cables be connected reversed, the camera can not get any
response from controller.
Notices: We suggest you select twisted cable which the copper
wire diameter more than 0.25mm. And if the transmission distance
more than 700 feet, we suggest you to select one Rs485 signal
amplifier. Or the Rs485 contral may not work properly.

3.3 RS-485 match resistance application
In order to get one good RS485 control, to avoid the reflection and disturbance of RS485 communicat-
ion signal or other signal, one terminal match resistance is needed on the last dome camera. Please make
the ten switch dail to ack panel.“ ON “ on the b
Controller
RS-485 terminal match resistance ON
Terminal match
resistance OFF
Terminal match
resistance OFF
Terminal match
resistance OFF
Notice
Please make sure the dome connects into voltage,use the acces-
sory power.
Please make sure the anode and cathode of RS-485 accurate to
avoid the dome can not be controlled.
5
Connection & Setup
RS485 Bus marching resister
To the application of system center control, in order to prevent
the reflection and interference of RS485 signal and other
communication signals, the communication port of farthest equipment
from control center should parallel connected with one marching
resister.

6
Protocol & Address Code Setting
Chapter 4 Protocol & Address Code Setting
Before installation, please check the Communication Protocol, Baud Rate and
Address Code of the control main machine in the system. There are two groups dip
switch which be used to set protocol, baud rate and address of dome camera. Please set
the dip switch consistent with system.
uThe disassemble way of transparent dome:
uFix screws
4-1. Protocol and baud rate setup of high speed dome camera
uProtocol & baud rate setup:
SWITCH
PRO0
(Pin 1)
PRO1
(Pin2)
PRO 2
(Pin 3)
Protocol/Baud Rate
OFF OFF OFF PELCO-D, 2400bps
ON ON OFF PELCO-P, 9600bps

Intelligent High Speed Dome Camera Address Setup
Before the application of high speed pan/tilt dome, the address code should be setup firstly. The add-
ress code is decided by the 8 bits dip switch on back panel which adopted with 8421 code. Support up to
255 pieces addresses. ON is respected by number 1. OFF is respected by number 0. Please check the atta-
ched address list at the back side of manual for the detailed setting way (Refer Chapter 10: Address code
DIP diagram) .
Notice
Factory default address code is 1.
Please make sure dip switch is on position, otherwise,the dome
camera will out of control.
Please make sure the dome can be controlled before installation.
The method of address code setup
Serial No.
Address Code
Dip switch has defined address number for each bit, as above diagram: No.1 stands for 1 address No.,
No.2 stands for 2 address No., No. 3 stands for 4 address No., and No. 4 stands for 8 address No. ,
how many channels you would like to set, just dip the relevant serial number to You can plus exi-
sting address bits., to get what you can not find from the dip switch diagram.
I.e. If you want to dip the 1 address No, just dip serial No. 1 to If you want No.37 address, just
dip No.1, No.4, No.32 to position
st
nd th th
st
¡
“on”.
“ON”.
“ON” .
1 Channel 37 Channels
7
Protocol & Address Code Setting
uCamera module setup:
ON/OFF
ZM0
(Pin 4)
ZM1
(Pin 5)
CAMERA
OFF OFF SONY
ON OFF YOKO
OFF ON CNB
ON ON LG
1. NTSC/PAL setup:
NT/PAL
(Pin 6) NTSC/PAL
OFF NTSC
ON PAL

Chapter 5:User Manual of The Controller
All the functions of IR high speed dome camera can be achieved through the control by keyboard. Be-
cause the detailed operation from different company is different, if the control system is from other comp
any,please control the dome according to the instruction from control system supplier. Some special fun-
ctions of high speed dome ask special operation , please connected with the control system supplier for de-
tailed operation way.
(We suggest choosing our controller with dome camera that can help you to get more function)
For the following description, control way is the same, no matter what protocol to be selected. Like Pleco-
D, Pelco-P !
5.1 Communication Protocol Selection
After connection of all together, the communication protocol selection will be show on the screen when
you press The protocol definition as bellow:”F4”.
PELCO P protocol 9600bps
PELCO D protocol 2400bps
“Pelco-P”
“Pelco-D”
The above definition is the switchover order for communication protocol according to the order of press-
ing on the key .“F4”
5.2 Camera Selection
Selecting any camera: Just input [255] address number, then input [CAM].
Selecting next camera: Input [+1], then the next camera be selected.
Selecting last camera: Input [-1], then the last camera be selected.
I.E. To Select No.2 camera:
Input [2], then input [CAM], the No.2 camera be selected; After No.2 camera be selected, input [+1], the
No.3 camera be selected; If we want to select No.1 camera after NO.2 camera be selected, just input [-1],
then the No.1 camera be selected;
5.3 P/T/Z Control
Input the camera series number which one you want to control.
Input [ZOOM+], [ZOOM-], [FOCUS+],[FOCUS-] or just move the joystick to control pan/tilt and lens
control
I.E. Control No.2 P/T/Z camera:
Input [2] + [CAM], then using joystick to move pan/tilt to the wanted position------input [ZOOM+],
[ZOOM-], [FOCUS+],[FOCUS-] to control dome camera.
8
User Manual of The Controller
5.4 Setup of P/T/Z Preset Points:
Select wanted camera, then use joystick to move the camera to appointed position.
Input [F1] + [8];
Input you wanted series number for this preset point ( from 1 128 );
Input [ PRE], then one preset point be established.

I.E. To establish No.15 preset point on No.5 camera:
Input [5] + [CAM] to select No.5 camera firstly.Zoom out lens then use joystick to move camera to wanted
position. Input [F1] + [15] + [PRE]
If want to establish different preset point, just change another series number, repeat the above operation.
5.5 Preset Point Call Back
(1) Manual Control:
Input the camera address number which one you want to control;
Input preset point number ( 128), the default number is 1.
Input [CALL], the wanted preset point be called back;
I.E. To call the No.6 preset point back on No. 3 camera:
Input [3] + [CAM] + [6] + [CALL], then the No.6 preset point on No.3 camera be called back.
(2). Automatically Control:
Input the camera address number which one you want to control;
Input the largest preset point number (2-16) which want to be automatically controlled, the default n-
umber is 8. The number of automatically controlled preset point can be different with different P/T/Z
camera, but the largest automatically control number is 16.
Input [RUN];
Revising the dwell time on preset point
Input the new dwell time (160), then input [DWL], after that the dwell time on all preset point be cha-
nged from 1 second to 60 second.
Input [7] + [CAM] to select camera, input [10] + [RUN], input [20] + [DWL], then the top 10 preset
point be called back automatically, dwell time is 20 second.
I.E. To automatically control the top 10 preset point on No.7 camera,the dwell time is 20 seconds:
(3). Termination of Preset Automatically Control:
To select you want to controlled camera;
Input [HOLD] or just move the joystick to stop automatically turning with this camera. Other camera
won't be affected;
Input [4] + [CAM], then input [HOLD] or just move the joystick, the automatically preset control on
No.4 camera be terminated.
I.E. To stop the automatically control on No.4 camera:
5.6 Deletion of Mistake Operation:
Input [DEL] can clean the input item on screen. If any mistake with input, just input [DEL] to
clean.
9
User Manual of The Controller
If controller without function key, it can realize the Pattern, Swing
and group function through call back relevant preset, the details as bellow:
2 patterns use from preset to operate the patterns which ha-
ve been setup.
8 Swings using from preset to operate the swings which h-
ave been setup
5 Groups use from preset to operate the swings which have
been setup..
“SAL”
“131” to “132”
“141” to “”148
“151” to “155”

CHAPTER 6: Guide of OSD Menu Application
Checking before Operation:
Checking the cable connection carefully before camera be powered;
The camera address ID of the controller must same of the camera address ID. The camera ID can be c-
hecked by reading DIP switch on PCB of camera.
If your controller supports multi-protocols, the protocol must be adjusted to the same as camera prot-
ocol.
The protocol changing on camera by DIP switch will come into work after camera restart.
Since the operation methods are different from different suppliers. Generally the operation of contro-
ller should base on the manual from the manufacturer of controller. Some special function of our high
speed dome camera can't be operated by other manufacturer's controller. There are some special dem-
ands and operations at some times, please connect with the dealer or manufacturer of you selected co-
ntroller.
Since preset 95 is used to start the OSD menu, so it can't be used as regular preset. Therefore, the des-
cription Presets 1~128 always means excluding Preset 95 in this manual“ ”
Self-Checking Information:
OSD Menu:
1.Function: With the application of OSD menu, Preset, Swing, Group, Pattern, Alarm I/O and other fu-
nctions can be setup for application.
Input [95] --- [CALL] to begin the application of OSD menu
.
1 0
Guide of OSD Menu Application

Guide of OSD Menu Application
Using joystick to move the cursor then input [FOCUS+] to selection wanted item.
SYSTEM INFORMATION selection is used to check system version information.
DISPLAY SETUP selection is used to setup what be shown on screen.
DOME SETUP selection is used to setup all functions of speed dome camera. It is
the main function selection.
EXTRA SETUP selection is used to setup unimportant setup of speed dome
1. DOME SETUP:
Please using joystick to move cursor to DOME SETUP selection. Then input
[FOCUS+] , the manu com e into the sub-manu as shown on followed:
1.1
This selection be used to setup the specifications of camea module.
With the selection, the camera functions of DIGITAL ZOOM, FOCUS
MODE, BACK LIGHT, DAY/NIGHT, AWB, SHARPNESS, IRIS MODE,
RESET CAMERA , CAMERA FLIP and PICTURE FREEZE can be setup
SETUP CAMERA:
1.2 SETUP MOTION:
This selection mainly be used to setup the specifications of the
movement of speed dome camera.
AUTO FLIP, MOTOR SPEED, PARK POSITION can be setup by this
selection.
1 1

Guide of OSD Menu Application
1.3 Preset:
Function: Up to 127 pieces preset can be set. Beside No.95, all presets can be named as 1---128. With t-
he combination of preset key and number key of controller, the preset point setup and call back function
can be quickly operated. And modify the default preset information. ( preset label, dwell time……)
Select camera, move camera to wanted position. Input [F1]---[8]---[preset num-Setup of Preset Point:
ber]---[PRE]
Input wanted preset number (default is 1), input [CALL], then the preset pointPreset Point Call Back:
be called back.
Please use the preset OSD menu to delete preset, or just setup another preset with the s-Preset Deletion:
Ame number to cover the old preset point;
The PRESET NO selection be used to setup the preset point series number. This series
number can be shown on screen.
The PRESET LABEL is used to edit the name of preset point.
The DWELL TIME selection is used to setup the stop time on preset point of camera. Using
joystick to move cursor to select wanted letter, then input [FOCUS+] to confirm.
The CLEAR PRESET selection is used to clear preset point.
1.4 SWING SETUP:
This selection is used to setup the swing movement of speed dome camera
With this function, the speed dome camera can move between two preset points.
1 2
Swing Running: Put swing number and add 10(11-18).then in [SAL];

10
1 4
Guide of OSD Menu Application
1.5 Group Function:
Function: The group function allows running up to 5 groups of preset, swing, pattern in sequence. Every
group including preset, swing, pattern, but the total function number can't more than 200 pieces. Throu-
gh the OSD menu operation, we can establish, modify, delete groups. The dwell time which be set with s-
wing function still workable when group function is working.
Group Running: Input the wanted group number + 20 numeric key ( say 21---25), then input [SAL].
I.E. To run No.5 group: Input [25]---[SAL];.
1.6. Pattern:
Function: The pattern function enables us to save and play camera motions created by joystick. Suppo-
rt up to 200 pieces movement command every pattern. Totally support 2 pieces pattern;
: Pattern can be created by the followed two ways:Pattern Setup
Using the numeric 1,2 and SAL to establish one Pattern:
Input [1---2], then press [SAL] more than 2 seconds to begin one establishment of pattern;
Using joystick to move camera to create the trace of pattern;
The limitation of movement is 200 pieces movement commands, the command number can be shown on
screen;
Input [Focus+] to save, [Focus-] to abandon;
Using OSD Menu to Establish Pattern:
Pattern Running:
Pattern Deletion:
Input numeric 1or 2 then input [SAL] to run one pattern;
Please use OSD menu to delete pattern;

6.Other Functions:
Information protection after power off:
180 auto flip function:
Park Function:
Privacy Zone Masking
This function can get back the last automatically running ac-
tion. Beside manual operation, preset, swing, trace recording, pattern all can be get back.
If the vertical turning of camera more than 90 camera can automatically 180
turning at horizontal direction. Then camera can continuously tracing objection.
With this function, camera can automatically turn to one special position to rectify mi-
stake which be accumulated through automatic turning. ( Normally, the park position is No.1 preset poi-
nt);
If the camera is not operated for a while, the camera also can turn to park position automatically. The w-
aiting time of park position is adjustable from
: ( SONY camera module only) In order to protect privacy, the speed dome cam-
era support 8 pieces masking zone to hide objections such as windows, shops or private space
¡ã ¡ã ¡ã
….!
7.OSD Display of Main Screen
P/T angle and Zoom information
Camera ID:
Action Title:
Preset Label
Alarm Input:
:
To show the Pan/Tilt position and zoom magnification;
The current camera address number.
Followings are possible Action Titles and their meaning.
When preset ~ is stored
: When camera reach to Preset ~
When undefined Preset number is called to move
When swing ~ is in action
: The label stored for specific preset point.
The has 4 channels input .If anyone point is ON state it will show a number corresponding
to each point.If the point is OFF state, will be displayed.
“SPRESET~ ”:
“PRESET ~”
“UNDEFINED”:
“SWING ~”:
”-”
10
1 3
Guide of OSD Menu Application
X010 ID:001
Alarm info
Date,time
table
Camera No
P/T/Z angle and
zoom information
Action title
8. Major Rules of Menu Operation
The menu items surrounded with ( ) always has its sub menu.
For all menu level, to go into sub menu, press [Focus+] key, to go up to upper menu, press [Focus] key. If
you learn by heart a rule that F+ is always similar to ENTER key and [Focus-] key is always ESC key, m-
any other functions of these keys will be easy to understand.

9.Main menu 10. Display Setup
This menu defines Enable/Disable of OSD disp-
lay on Main Screen. If an item is set to be AUTO,
the item is displayed only when the value of it is
changed.
10
1 3
Guide of OSD Menu Application
MAIN MENU
1.SYSTEM INFORMATION
2.DISPLAY SETUP
3.DOME SETUP
4.EXTRA SETUP
DISPLAY SETUP
1.CAMERA ID
2.ACTION TITLE
3.PTZ INFO
4.PRESET LABEL
5.ALARM INFO
6.SYSTEM TIME
BACK
EXIT MENU
ON
ON
ON
ON
ON
ON
To move from item to item, use Up/Down of the joystick in the Up/Down or Left/Right.
If you want to confirm a menu item, press [Focus+] key.
To change a value of an item, use Up/Down of the joystick in the controller. After you change a value, pr-
ess [Focus+] key to save it or press [Focus-] key to cancel it.

12.PTZ Motion setup
The maximum manual speed is listed below w-
hen zoom is *1. As zoom magnification is incr-
eased, the speed will be decreased to maintain
equal controllability.
High speed 0 ~180 /sec
Middle speed 0 ~90 /sec
Low speed 0 ~90 /sec
° °
° °
° °
13.Park Action Setup
This function enables to locate the camera to spe-
cific position automatically if operator doesn't o-
perate the controller for a while. The park Time
can be defined as an interval from 1 min. to 4 ho-
urs.
14.Preset Setup
15.Edit Preset Label
LAB FOR PRE:
1.The cursor presents the current input position of
the label letter.Upon the letter be selected , the cu-
rsor move to left.
2.Using the DOWN IGHT EFT of
the joystick, the right letter can be selected from a-
lphabet . After selection of the correct letter, input
[FOCUS+].
3.After all letters be set, move joystick to
hen input [FOCUS+] to save the modification . If
you want to cancel the setup of label, just move j-
oystick to ANCE then input [FOCUS+] to c-
ancel.
“UP”,” ”,”R ”,”L ”
“OK” t-
“C L”
10
1 4
Guide of OSD Menu Application
MOTION SETUP
1.REBOOT ACTION
2.AUTO FLIP
3.MOTOR SPEED
4.JOG DIR
5.PARK SETUP
BACK
EXIT MENU
ON
OFF
NORMAL
NORMAL
PRESET SETUP
1.PRESET NO
2.PRESET LABEL
3.DWELL TIME
4.CLEAR PRESET
BACK
EXIT MENU
001
3
PRESET SETUP
LABEL FOR PRESET
0123456789
ABCDEFGHIJ
KLMNOPQRST
UVWXYZabcd
efghigklmn
opqrstuvwx
yz-/-;,.-
001
PARK SETUP
1.PARK ENABLE
2.PARK TIME
3.PARK PRESET
BACK
EXIT MENU
OFF
00:05
001

16.Swing Setup:
SWING NUMBER: 1/8; This P/TZ camera support up to 8 pieces swing scan. This item is used to set
the series number of swings.
L POSITION: PRE 001; The 001 preset point be set as the left side of swing;
R POSITION: PRE 002; The 002 preset point be set as the right side of swing;
SWING SPEED: AUTO; The speed dome swing. AUTO is default of system;
LOOP: 1; The times of swing turning ( be used for GROUP function only)
DIRECTION: AUTO; The direction of swing turning;
RUN SWING To run swing;
10
1 5
Guide of OSD Menu Application
SWING SETUP
1.SWING NUMBER:
2.1ST POSITION:
3.2ND POSITION:
4.SWING SPEED:
5.LOOP COUNTER
6.DIRECTION:
7.CLEAR SWING:
8.RUN SWING:
BACK
EXIT MENU
1
001
001
30d/s
3
LEFT
17.Pattern Setup:
PATTERN SETUP: To establish one pattern for camera auto turning;
PATTERN NUMBER 1/2; Camera support 2 pieces pattern, using this item to edit the series number
of pattern;
RECORDER; The times of pattern turning ( for GROUP only);
PROGRAM PATTERN: Using joystick to program the trace of camera, total support 500 pieces co-
mmands for one piece pattern.
CLEAR PATTERN: To delete one pattern;
RUN PATTERN: To run one pattern;
PATTERN SETUP
1.PATTERN NUMBER:
RECORDER:
2.PROGRAM PATTERN
3.CLEAR PATTERN
4.RUN PATTERN
BACK
EXIT MENU
1/2
000