5. To attach the Line Tightner weave the poly wire though the
holes of the Line Tightener at either end, and tie the poly wire
to the other end (See Picture on Previous Page).
6. ttach the
metal snap
hook in the
loop next to
your knot (See
Picture).
7. Complete this assembly for all three poly-wires.
8. Insert the first poly wire’s loop
into the lowest black insulator in
the location where you want your
opening and unwind poly wire off
winder. (Figure 1).
9. Slide the poly wire into each black
insulator on the poles as you
position the wire around the
inside of the poles.
NO E: The opposite end of the poly
wire contains a metal clip, which will
be used to hook into the beginning
loop of the poly wire once you wrap
it around the perimeter.
10. Hook the clip end of the poly
wire to the poly wire’s loop (Figure 2). The hook completes
the connection.
NO E: Do not over tighten the poly wire at this time.
11. Repeat steps 4 through 6 until all three poly wires are attached
to the poles.
12. Using the Line Tightener
located behind the poly wire
metal hook, adjust the tightness
of each poly wire until they
have equal tension (Figure 3).
Tighten only until the slack is
removed.
NO E: void over tightening,
which will cause other wires to sag.
13. s you tighten, slide the Line
Tightener back to take up the
slack.
14. Use the flagging tape to mark
the two top poly wires for
visibility (Figure 4).
IMPPOR AN : A common behavior of bears is to investigate
the flagging tape once near the fence. Increasing the likelihood
of getting a good shock.
NO E: Make sure there are no green branches or other vegetation
touching the top two poly wires as they will weaken the voltage
and deplete the batteries. The bottom poly wire may be touching
the ground, as it is a grounded wire.
3 Energizer hookup Important Safety Information
Read Energizer Instructions Carefully.
WARNING: ny alteration to the design of this energizer may
cause serious electrical shock and may void the warranty.
• Install the energizer and the electric fence according to these
installation and operating instructions.
• Inform everyone, especially children, who might possibly
come into contact with the electrically charged fence, about
its location and operation. Do not allow young or infirm
persons to use this electric fence energizer without
supervision. Do not allow young children to play with this
energizer or near an electric fence or electrified wires.
• Instruct all persons how to disconnect the energizer in case of
emergency
• Never climb over an electric fence wire while it is electrically
energized
• Never install an electric fence below high-voltage poser plant
transmission lines.
• Never use more than one electric fence energizer on the same
fence.
• properly installed ground stake electrically connected to the
fence energizer output ground terminal provides grounding of
this product. The energizer must be grounded. If the energizer
should malfunction, grounding will reduce the risk of
electrical shock by providing a path of low resistance for the
electric current.
DANGER: n internal fault on an improperly grounded fence
energizer could result in a risk of harmful electric shock on the
electrified fence.
3.1 Insert batteries (See Energizer Instructions)
3.2 Install your energizer to the electric fence
1. ttach the energizer directly to the
fence poly wire using the unique
top stay-on clip. ttach the stay-on
clip to the middle poly wire by
inserting the stay-on clip into the
poly wire starter loop (Figure 5).
This will allow you to hang the unit
without sagging the fence.
2. Choosing a color, attach the “hot”
wire with alligator clips between the
top two poly wires using the
alligator clips.
3. ttach the green ground clamp that is attached to the
Energizer to the ground stake.
4. ttach the other color “ground” wire to the bottom poly wire
and to the ground stake using the alligator clips. Put the small
alligator clip into the hole of the ground stake to clamp it.
5. Your energizer is ready to be turned on (See Energizer
Instructions).
Questions: Call Toll Free 866 EAR 911
8:00 AM - 5:00 PM MST Monday through Friday
ATTENTION! DO NOT RETURN TO STORE!
For product repair or return please call UDAP Industries at 406-494-9292
Disclaimer
DO NOT SEEK OUT ENCOUNTERS WITH BEARS. THIS PRODUCT IS A BEAR DETERRENT WHICH MAY PROTECT USERS IN SOME
UNEXPECTED CONFRONTATIONS WITH BEARS BUT MAY NOT BE EFFECTIVE IN ALL SITUATIONS OR PREVENT ALL INJURIES OR
DAMAGES. READ CAREFULLY THE ENTIRE INSTRUCTIONS UPON PURCHASE & BEFORE TAKING THIS PRODUCT INTO AREAS
WHERE BEARS MIGHT BE ENCOUNTERED. KEEP OUT OF REACH OF CHILDREN.
TO THE EXTENT ALLOWED BY LAW, UDAP INDUSTRIES, INC. SHALL NOT BE LIABLE FOR DAMAGE, INJURY, LOSS, DIRECT OR
CONSEQUENTIAL INCLUDING DEATH ARISING OUT OF THE USE OF, OR INABILITY TO USE THIS PRODUCT.
PepperPower.com
