UDP Technology IPC4100A-25D User manual

IPC4100
Hardware Manual
(IPC4100A-25D, IPC4100A-23)

IPC 4100 Hardware Manual
Table of Contents
1. INTRODUCTION...................................................................................................................3
2. Product Description ................................................................................................................4
2.1. Specifications.................................................................................................................. 4
3. INSTALLATION & CONFIGURATION............................................................................. 6
3.1. Package Contents ............................................................................................................ 6
3.2. Part List........................................................................................................................... 7
3.3. Basic Configuration of IPC4100..................................................................................... 8
3.4. DIP Switch Setting........................................................................................................ 10
3.5. Setting Address(ID) of Dome Camera .......................................................................... 12
3.6. Connecting Wiring ........................................................................................................ 14
4. Operation Description...........................................................................................................17
4.1. Factory Default Settings................................................................................................ 17
4.2. Rebooting...................................................................................................................... 17
4.3. On Screen Menu ........................................................................................................... 17
5. TECHNICAL SPECIFICATIONS ......................................................................................18
6. DIMENSIONS.......................................................................................................................20
APPENDIX A - The List of GLB(Short) Key .........................................................................21
APPENDIX B - TROUBLE SHOOTING...............................................................................23
APPENDIX C - OPTIONAL ITEMS...................................................................................... 24
1. HOUSING & ACCESSORY ........................................................................................... 24
Revision history......................................................................................................................... 29
C UDP Co., Ltd. 2

IPC4100 Hardware Manual
1.INTRODUCTION
This IPC4100 compress video/audio data and transmit the compressed video/audio data through
the network in real time. IPC4100 provides a high quality video image with a limited bandwidth
and storage capacity. These products are ideally suited for a wide range of surveillance and
remote monitoring applications. Main features are highlighted below.
Main features
• High Quality Compression in real time streaming
• NVE provides high quality MPEG-4 and MJPEG encoding at D1 in real time. Main
features
Network
• RTP/RTSP and unicast/multicast are supported.
Streaming
• IPC4100 supports de-interlacing by hardware.
Video/Audio
• Loop out is supported
• IPC4100 supports two ways audio
Transmits to client - G.711 by software
Receives from client - one digital audio
Camera
• 25X Auto Focus Optical Zoom Lens, 10X Digital Zoom (Total 250X Zoom Ratio)
• Day / Night with removable IR Cut Filter (Auto ICR)
• DSS (Digital Slow Shutter) : (IC4100A-25D Only)
• Minimized Vibration at slow speed
• Auto Flip 180 Dome Rotation
• Turbo speed is maximum 430 per seconds
Additional Features
• Motion detection by hardware.
• On Screen Display (OSD) by hardware.
• RS-485 serial port
• RS-232C serial port for some devices like a POS terminal.
• IPC4100 supports built-in surge protection and lightning protection circuit.
SDK
• Four types (RTSP, UDA5, ActiveX, HTTP-API) are provided for application
development.
C UDP Co., Ltd. 3

IPC4100 Hardware Manual
2.ProductDescription
2.1.Specifications
IPC4100 specification is shown as following Table
Network
IPC4100A-25D IPC4100A-23
Video Compression MPEG-4, JPEG
Resolution D1, 2CIF, CIF, QCIF
Compression FPS 25/30 fps @ D1
Audio Input/Output 1 / 1 ch
Compression PCM(software compression : G.711, uLaw)
Network 10/100 Base-T
RS-232C Supported
RS-485 / 422 Supported
De-interlacing Supported by hardware
Motion Detection Supported by hardware
OSD & Private
Region Masking Supported by hardware
Video Stream Encryption AES
Protocol TCP,UDP,DHCP,HTTP,NTP,RTSP,RTP(Unicast,Multicast)
Camera
IPC4100A-25D IPC4100A-23
Pick Up Device Sony ¼
”
Super HAD CCD
Effective Pixels NTSC –768(H) x 494 (V) / PAL –752 (H) x 582(V)
Television System 2 : 1 Interlace
Horizontal Resolution NTSC –470 TVL / PAL –460 TVL
Minimum Illumination
1.0 Lux (30 IRE)
Day / Night Off (Color)
1.0 Lux (30 IRE)
0.1 Lux (30 IRE)
Day / Night On (B & W)
0.01 Lux
Slow Shutter x 128 On
0.001 Lux (30 IRE)
Day / Night On (B & W) + DSS
Lens 25X Optical Day / Night 23 X Optical
F 1.6 f=3.8 ~ 95 mm F1.6 f=3 .8 ~ 87.4 mm
S/N Ratio 50 dB 49 dB
C UDP Co., Ltd. 4

IPC4100 Hardware Manual
Dome
IPC4100A-25D IPC4100A-23
Pan Angle / Speed 360 Continuous Rotation, 0.1 ~90 / Sec
Turbo Speed : 430 / Sec
Preset Speed 360 / 430 /500 Selectable, Default 360 / Sec
Tilt Angle / Speed 0 ~ 94, 0.1 ~90 / sec (According to Zoom Ratio)
Camera ID 999
Home Default / Preset / Tour /Auto Scan /Patter Programmable
Preset 319 Position (16 Characters Input)
Auto Scan 8 Auto Scan
Guard Tour 8 Guard Tour (Preset, Pattern, Auto Scan, Tour Input)
Pattern 4 Pattern (240 Sec Memory)
Remote Control Network / RS-485, 422
Alarm Input 2 Inputs (NC/NO)
Alarm Output 1 Relay 24 VAC / 1 A (NC/NO)
Global Key Available
Self Monitoring Software Built-in
On Screen Display Camera ID, Pan / Tilt Angle, Flip, Zoom etc,
Material Aluminum / PC
Color Black
Dimensions 137.3 x 205 (D) mm
Weight 1,850 g
C UDP Co., Ltd. 5

IPC4100 Hardware Manual
3.INSTALLATION&CONFIGURATION
3.1.PackageContents
The Package contains the following
IPC4100.------------------------------------------------------------------------- 1
Plastic Anchor ------------------------------------------------------------------ 3
Screws for Plastic Anchor ----------------------------------------------------- 3
Surface Mount Bracket Adapter---------------------------------------------- 1
LAN Cable (Cross Type 1.5m) ----------------------------------------------- 1
7 Pin Terminal Block ---------------------------------------------------------- 1
3 Pin IPC Cable ---------------------------------------------------------------- 1
6 Pin IPC Cable ---------------------------------------------------------------- 1
C UDP Co., Ltd. 6

IPC4100 Hardware Manual
3.2.PartList
Figure 1. Part List
C UDP Co., Ltd. 7

IPC4100 Hardware Manual
C UDP Co., Ltd. 8
3.3.BasicConfigurationofIPC4100
Figure 2. Basic Installation Configuration
The dome camera is for use in surface mounting applications and the mounting surface should
be capable of supporting loads up to 10 lb(4.5Kg)
The dome camera’s base should be attached to a structural object, such as a hard wood, wall
stud or ceiling rafter that supports the weight of the dome camera.
Sesor
Siren
Flashing Light
Analog Monitor
MIC
Amp Speaker
MIC4DVR
Alarm Input
Up to 2
AC 24V
Power supply
AC 24V
Power supply
AC 24V
Power supply
Alarm Output
Up to 2
Client PC
Ethernet Network

IPC4100 Hardware Manual
C UDP Co., Ltd. 9
Figure 3. Bubble Dome
Figure 4. Installation of ceiling mount
The dome camera must be installed by qualified service personnel in accordance with all local
and federal electrical and building codes. The system should be installed according to Figure 2
hrough Figure 10.

IPC4100 Hardware Manual
C UDP Co., Ltd. 10
Figure 5. Layout of Switches
3.4.DIPSwitchSetting
ith a Cyber Scan joystick controller or if a dome camera is
controlled through the network, select Cyber Scan II Protocol and if Consult service personnel if
If a dome camera is to be installed w
a dome camera is installed with device other than a joystick.
Protocol Setting

IPC4100 Hardware Manual
C UDP Co., Ltd. 11
Communication Speed
Communication Type
System Type (Factory Use)
Figure 6. DIP Switch Setting
Termination Setting
8 FUNCTION
ON PAL
OFF NTSC
ON
8
NTSC/PAL
1 2 3 4 PROTOCOL
OFF OFF OFF OFF Cyber Scan I
OFF OFF OFF ON P-D Type
OFF OFF ON OFF P-P Type
OFF ON OFF OFF G-Speed Dome
ON OFF OFF OFF SNS Type
OFF ON OFF ON KAL Type
OFF ON ON OFF DEN Type
OFF ON ON ON BOS Type
ON OFF OFF OFF SAMS Type
ON OFF OFF ON SAE Type
ON OFF ON OFF Reserved
ON OFF ON ON Reserved
ON ON OFF OFF Reserved
ON ON OFF ON Reserved
ON ON ON OFF Reserved
ON ON ON ON C
y
ber Scan II
ON
1234
Protocol
* Factory Mode : Cyber Scan II
5 6 BAUD RATE
OFF OFF 9600
OFF ON 4800
ON OFF 2400
ON ON 38400
ON
65
BaudRate
7 FUNCTION
ON RS-422
OFF RS-485
ON
7
RS-422/485 * Factor
y
Mode : RS-485

IPC4100 Hardware Manual
C UDP Co., Ltd. 12
The device which is connected at end of line, whether it be a dome camera or joystick controller,
he dome camera must be installed by qualified service personnel in accordance with all local
must have the cable for communication terminated by setting the appropriate DIP switch.
Without proper termination, there is potential for control signal errors. Total length of the
cable for communication should not exceed 1.2Km.
Figure 7. Setting Unit for Termination
T
and federal electrical and building codes. The system should be installed according to Figures 2
through 10.
Figure 8. Termination Diagram
3.5.SettingAddress(ID)ofDomeCamera
9 10 Function
ON ON Termination
OFF OFF Not Terminated
ON
109
Termination * Factor
y
Mode : Not Terminated

IPC4100 Hardware Manual
To prevent damage, each dome camera must have an unique address(ID). When installing
multiple dome cameras using a multiplexer, it is suggested that the dome camera address
matches the multiplexer port number.
DOME ID SW100 SW10 SW1
1 0 0 1
2 0 2
. . . .
999 9 9 9
- SW 100 : MSB(Most Significant Bit)
- SW 1 : LSB(Least Significant Bit)
Figure 9. Setting Address(ID) of Dome Camera
C UDP Co., Ltd. 13

IPC4100 Hardware Manual
3.6.ConnectingWiring
A L A R M I N P U T
R S - 2 3 2 R S - 4 2 2
I
N
1
I
N
2
G
N
D
R
x
T
x
G
N
D
T
R
X
+
T
R
X
-
T
X
+
T
X
-
R S - 4 8 5
N O
N C
C O M
A u d i 0 I n
A u d i o O u t
G N D
A L A R M
O U T P U T
A U D I O
E T H E R N E T
R E S E T
I
N
1
I
N
2
G
N
D
R
x
T
x
G
N
D
T
R
X
+
T
R
X
-
T
X
+
T
X
-
G
N
D
A
U
D
I
O
O
u
t
A
U
D
I
O
I
n
C
O
M
N
C
N
O
R S - 2 3 2 R S - 4 2 2
R
x
T
x
G
N
D
T
R
X
+
T
R
X
-
T
X
+
T
X
-
R S - 4 8 5
S e r i a l
c o m m u n i c a t i o n
V i d e o O u t p u t
C o n n e c t o r
1
2
A l a r m I n p u t
3
A l a r m O u t p u t / A u d i o
4
E T H E R N E T
5
P o w e r
6
R e s e t
S / W
7
Figure 10. Connecting Wiring
C UDP Co., Ltd. 14

IPC4100 Hardware Manual
①7 pin terminal block for serial communication
RS-232C Terminal Block is used for some devices such as POS terminal block.
Figure 11. RS-232C Connection
The RS-485 serial port consists of TRX+(RX+) and TRX-(RX-) as following Figure 12.
Figure 12. RS-485 Connection
The RS-422 serial port consists of TRX+(RX+), TRX-(RX-), TX+ and TX- as following Figure
13.
Figure 13. RS-422 Connection
②BNC connector for video loop out
C UDP Co., Ltd. 15

IPC4100 Hardware Manual
Connect the video out (BNC) connector to the monitor or video input.
③3 pin terminal block for D/I
You can use external devices to signal the dome camera to react to events. Mechanical or
electrical switches can be wired to the IN(Alarm In) and GND(Ground) connectors.
GND(Ground)
Note : All the connectors marked GND are common.
Connect the ground side of the Alarm input to the GND connector.
④6 pin terminal block for D/O and audio
The dome camera can activate external devices such as buzzers or lights. Connect the device to
the NC(NO)(Alarm Out) and COM(Common) connectors.
⑤LAN connector (Ethernet)
This is a RJ45 LAN connector for 10/100 Base-T Ethernet.
Figure 14. RJ45 LAN connector
⑥Terminal block for the Power
Connect the power of AC 24V 850mA to the dome camera.
⑦ Reset Switch (Reset)
Reset switch is used for restarting NVE or resetting NVE as Factory Default (FD). Refer to ‘4.1.
Factory Default Settings’ for detailed procedures. (This function is not implemented yet)
C UDP Co., Ltd. 16

IPC4100 Hardware Manual
4.OperationDescription
4.1.FactoryDefaultSettings
Factory default settings are as follows:
• IP address: 192.168.xx.yy (refer to 2.3 Serial Number / MAC Address)
• Mask: 255.255.0.0
• Gateway: 192.168.0.1
• User ID: root
• Password: pass
MAC address = 00-13-23-01-23-45 →IP address = 192.168.35.69
Convert the Hexadecimal number to Decimal number
Factory Default (FD) initialization procedure is as follows
1. Turn ON the power.
2. Press “Reset” button when Status LED at LAN connector start to blink very rapidly.
3. Release “Reset” button when Status LED at LAN connector is blinking slowly.
4.2.Rebooting
Reset can be carried out as follows:
1. Press Reset for 1 second.
When Reset function is activated, Status LED and Network LED at LAN connector will
blink together, twice. User may stop pressing Reset at this point.
2. When “Reset” function has been completed, LEDs will stop blinking.
4.3.OnScreenMenu
Please refer to “On Screen Menu Operation Manual of IPC PTZ Type Camera.pdf”.
C UDP Co., Ltd. 17

IPC4100 Hardware Manual
5.TECHNICALSPECIFICATIONS
Camera : 25XDN
Minimum Illumination 1.0 lx (30 IRE) ; Day & Night Off (Color )
0.1 lx (30 IRE) ; Day & Night On (Black & White)
0.01 lx ; Slow Shutter X 128 On
0.001 lx(30IRE) ; Day & Night On(Black & White) + DSS
Lens 25X Optical Zoom with Auto Focus(10X Digital Zoom)
(F=1.6 ~ 3.7, 50IRE, 3.8mm~95mm)
S/N ratio 50dB
Minimum object distance 0.1m
Camera: 23X
Minimum Illumination 1.0 lx (30 IRE)
Lens 23X Optical Zoom with Auto Focus(10X Digital Zoom)
(F=1.6 ~ 3.8, 50IRE, 3.8mm~87.4mm)
S/N ratio 49dB
Minimum object distance 1m
General
Certification CE EMC, FCC CLASS A
Image Sensor NTSC 1/4" SONY Super HAD CCD, 768(H) x 494(V)
PAL 1/4" SONY Super HAD CCD, 752(H) x 582(V)
Horizontal Resolution 470/460 lines(NTSC/PAL)
Pan Angle 360°Continuous rotation
Manual Speed 0.1°to 90°/sec. (Proportional to zoom)
Turbo speed: 430°/sec (Press “CTRL”and move the joystick)
Preset Speed 500°/sec. maximum (OPT : 430, 360)
Tilt Angle 0°to 94°(User selectable to prevent obstruction of the horizontal
view)
Manual Speed 0.1°to 90°/sec. (Proportional to zoom)
ID (Camera Address) 999 Selectable Address
Preset Position 319 Positions with camera status (16Characters input)
Alarm Out 4 Relays 24 VDC/1A Max (Selectable NC/NO)
Alarm Input 8 Input normal open dry contact (Programmable NC/NO)
On-Screen Display Displays camera ID, Pan/Tilt Angle, Flip, Zoom, Privacy Zone
Tour 8 Guard Tours (Preset , Pattern, Auto Scan, Tour Input)
Pattern 4 Pattern, 240sec Memory
Flip Rotate 180 at bottom of tilt
Communication Type RS-485/422,Baud Rate: 9600bps(STD), (OPT : 38400, 4800, 2400)
Micro Step 0.01°
Access Time 0.75 second maximum preset recall time
C UDP Co., Ltd. 18

IPC4100 Hardware Manual
Electrical
Environmental
Ambient Environment
Temperature
-20℃to 60℃(-4℉~140℉)
Operating Humidity 0~90% RH(Non-Condensing)
Storage Temperature -30℃to 70℃(-22℉~158℉)
Mechanical
Construction Aluminum steel and Plastic
Finish Polyester Power Coat
Dome Bubble Polycarbonate
Dimensions See Figure 12-A,B
Input voltage 24 VAC
Current 651 mA
Consumption 15.61 W
C UDP Co., Ltd. 19

IPC4100 Hardware Manual
6.DIMENSIONS
Figure 15 Cyber Scan Dome
Figure 16 Surface Mount Bracket Adaptor
C UDP Co., Ltd. 20