ULTRA SABERS UltraProffie ZERO User manual

UltraProffie
Apprentice’s Guide
Short click: toggle POWER
Long press: toggle background TRACK
Double-click: activate PRESET control
Double-twist with button pressed: activate PROFILE control
Double-tap with button pressed: switch STEALTH / COMBAT
UltraSaber Controls
ZERO
Motion Effects
Momentary effects triggered by motion
Smooth swing
Swing the saber in any direction.
Clash
Hit the blade anywhere.
Stab
Slide firmly along the blade axis.
Force
Twist back-and-forth around the blade axis
to use the Force!
Drag
With the BUTTON pressed, HIT THE GROUND with the tip of your saber. Effect ends when you
release the button. Only operational in Earth-like gravity.
Melt
STAB HORIZONTALLY with the BUTTON pressed to concentrate The Force at the tip of your saber!
Lockup
When two sabers collide, the clash of energies might lock them to each other. Trigger a CLASH
with the saber POINTING UP and the BUTTON pressed, and you’ll activate the Lockup. Effect ends
when you release the button.
Lightning
Your saber can absorb Force Lightning if it’s prepared for it! Keep it horizontal and SHAKE it with
the BUTTON pressed until you hear it arming. Next CLASH will trigger the Lightning effect, which
you can end with an ample SWING. Disarm with a short SHAKE at any time.
Choreographic Effects
Persistent effects controlled with the button
Blaster Hybrid
Your saber can be converted into a Blaster. The Blaster Hybrid must be preliminary charged, then disarmed in order to resume saber functions:
SHAKE your saber CONTINUOUSLY until the charging sound ends in blasts. The Blaster Hybrid has been activated!
The button is now your trigger - CLICK to blast!
Disarm with a short SHAKE at any time.
Analog presets
1 Solid
2 Shimmer
3 Fast Pulse
4 Audio Shimmer
5 Real Pulse
6 Morph
Pixel presets
1 Solid Green
2 Solid Red
3 Solid Arctic
4 Solid Orange
5 Solid Lime
6 Solid Bane
7 Solid Sunrider
8 Solid Hot Pink
9 Solid Blue
10 Solid Violet
11 Hump Flicker
12 Saw Blade
13 Audio Flicker
14 Surging Pulse
15 Power Surge
16 Omni Color
17 Rainbow
18 Lava Lamp
19 Thunder Storm
20 Gradient
21 Stable Unstable
22 Split Blade
23 Anger
24 Rolling Pulse
25 Smoke Blade

Preset Control
Profile Control
TWIST GESTURES
You navigate through Controls using twist gestures:
Twist to the RIGHT until you hear a tick, to
navigate one step FORWARD.
Twist to the LEFT until you hear a tick, to navigate
one step BACKWARD.
TWIST in any direction with the BUTTON pressed
to PAUSE navigation. As long as the button stays
pressed, navigation stays paused.
TWIST FIRMLY in any direction to start SCROLLING,
either forward or backward.
Twist in the OPPOSITE direction to STOP
SCROLLING.
CONFIRM your option with a short click. CANCEL at
any time with a long press of the button.
Combat vs. Stealth Mode
In COMBAT mode you can use the saber at full power. In STEALTH mode you can only use up to 1/3.14 - this saves energy and makes your saber hardly detectable by others around.
To switch between Combat and Stealth modes, hold the hilt still and TAP it (not the blade!) TWICE, with the BUTTON pressed.
The volume and brightness of Combat and Stealth modes are individually adjustable through the Profile Control.
Click the power
button twice
If your saber is powered off,
it will turn on. Wait until you hear the
preset annunciator.
Choose a preset
using twist gestures
Once the tick/scroll settles,
the new preset will be
applied for preview.
Click to confirm
The preset selection will be saved and
the saber will resume the previous
power state.
Twist the hilt twice with the button pressed
Wait until you hear the annunciator.
Choose a parameter to edit using twist gestures
Sensitivity
Master sensitivity
applies to all
motions.
Color
Main color of
the current
preset.
Volume
Sound volume for
the current Combat
or Stealth mode.
Brightness
Blade brightness for
the current Combat
or Stealth mode.
Edit the selected parameter using twist gestures
Preview instantly
Click to confirm
Click to confirm
Energy Saving
Maintenance
Troubleshooting
If left IDLE in Combat mode, your saber will eventually switch to STEALTH mode. Any saber action such as a swing or a clash will resume Combat mode.
If left IDLE in Stealth mode, you saber will eventually POWER OFF.
If there’s not enough energy in your BATTERY to maintain the Force, your saber will automatically POWER OFF.
If unused for more than a few weeks, remove the battery or recharge it periodically.
Contact UltraSabers Customer Support at [e-mail] for authorized firmware updates.
Nothing happens when I press the power button.
Check the physical integrity of the board and wire harness.
Check battery polarity - positive should go towards the speaker. Try replacing with a new and fully charged battery.
When I press the button the saber just plays
a sound but doesn’t light up.
The battery is discharged. Replace or recharge the battery.
The saber doesn’t respond to any command.
Remove the battery, wait a few seconds, then reinsert the battery. Software glitches are rare but easily fixed.
Can’t access the extension connector, it is sealed.
Your saber’s warranty is still valid. Unauthorized access to the extension connector will void the warranty.
The hilt gets warm.
This is normal for certain installations. If it becomes uncomfortable, turn it off and let it cool for a few minutes. If it
gets hot immediately after powering on: power off, let it cool, remove the battery and request technical assistance.
I need technical assistance.
Contact Ultrasabers Customer Support at [e-mail]
Made in Romania by RSX Engineering
Open-source firmware based on ProffieOS
For customization go to www.ultraproffie.com
PZ 3 1 L P - RF
PZ: UltraProffie Zero
PL: UltraProffie Lite
2: 2W Audio
3: 3W Audio
RF: Regular form
SF: Short form
0: No battery charger
1: 1A battery charger
L: LSM Accelerometer
& Gyroscope
P: Protected
NP: Not protected
Supply Voltage
3.2 - 4.2 [Volts]
Supply Current
Maximum: 4.9 [Amperes] DC
Charging Voltage
4.5 - 7.0 [Volts]
Charging Current
Default: 0.85 [Amperes]; Maximum: 1.0 [Amperes]
Standby Current
0.2 [milliAmperes]
Audio Power
Maximum: 3 [Watts] RMS
Analog LED Channels
2
Pixel Channels
1
Processor
ARM Cortex M4, 256 [kBytes] Flash, 64 [kBytes] RAM - STM32L431 @ 80 [MHz]
Storage Memory
Single-font internal Flash
Data Interfaces
UART, I2C, SWD
Technical Specifications
5V / 1A Charger or USB BC1.2
MicroUSB. No data.
3W Bass Speaker
Extension Connector
18650 Li-Ion Battery
+
-
1.25” Chassis
Main Connector
(Regular form only)