Ultrak KC33W4MM User manual

KCMU000002
05/30/01
KC33W4MM
1/3" CCD BLACK-AND-WHITE
PROFESSIONAL OBSERVATION
SYSTEM CAMERA
USER
MANUAL
Ultrak Worldwide Support Center
Sales & Technical Support
1301 Waters Ridge Drive • Lewisville, TX 75057
[phone] • [phone] • FAX [phone]

ii KCMU000002
05/30/01
ISSUE 1 – May 2001
2001 BY ULTRAK
ALL RIGHTS RESERVED
PRINTED IN USA
ULTRAK CORPORATE OFFICE
1301 WATERS RIDGE DRIVE
LEWISVILLE, TX 75057
[phone]
ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED
BY ANY MEANS WITHOUT WRITTEN PERMISSION FROM ULTRAK.
THE INFORMATION IN THIS PUBLICATION IS BELIEVED TO BE ACCURATE IN ALL
RESPECTS. HOWEVER, ULTRAK CANNOT ASSUME RESPONSIBILITY FOR ANY
CONSEQUENCES RESULTING FROM THE USE THEREOF. THE INFORMATION
CONTAINED HEREIN IS SUBJECT TO CHANGE WITHOUT NOTICE. REVISIONS OR
NEW EDITIONS TO THIS PUBLICATION MAY BE ISSUED TO INCORPORATE SUCH
CHANGES.
USERS OF THIS PRODUCT ARE RESPONSIBLE FOR CHECKING AND COMPLYING
WITH ALL FEDERAL, STATE, AND LOCAL LAWS AND STATUTES CONCERNING
THE MONITORING AND RECORDING OF VIDEO AND AUDIO SIGNALS. ULTRAK
SHALL NOT BE HELD RESPONSIBLE FOR THE USE OF THIS PRODUCT IN
VIOLATION OF CURRENT LAWS AND STATUTES.

iii KCMU000002
05/30/01
FCC COMPLIANCE STATEMENT
INFORMATION TO THE USER: THIS EQUIPMENT HAS BEEN
TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A
CLASS B DIGITAL DEVICE, PURSUANT TO PART 15 OF THE
FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE
REASONABLE PROTECTION AGAINST HARMFUL INTERFER-
ENCE IN A RESIDENTIAL INSTALLATION. THIS EQUIPMENT
GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY
ENERGY AND, IF NOT INSTALLED AND USED IN ACCORDANCE
WITH THE INSTRUCTIONS, MAY CAUSE HARMFUL INTERFER-
ENCE TO RADIO COMMUNICATIONS. HOWEVER, THERE IS NO
GUARANTEE THAT INTERFERENCE WILL NOT OCCUR IN A
PARTICULAR INSTALLATION. IF THIS EQUIPMENT DOES
CAUSE HARMFUL INTERFERENCE TO RADIO OR TELEVISION
RECEPTION WHICH CAN BE DETERMINED BY TURNING THE
EQUIPMENT OFF AND ON, THE USER IS ENCOURAGED TO
TRY TO CORRECT THE INTERFERENCE BY ONE OR MORE OF
THE FOLLOWING MEASURES:
- REORIENT OR RELOCATE THE RECEIVING ANTENNA
- INCREASE THE SEPARATION BETWEEN THE EQUIPMENT
AND RECEIVER
- CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT
DIFFERENT FROM THAT TO WHICH THE RECEIVER IS
CONNECTED
- CONSULT THE DEALER OR AN EXPERIENCED RADIO/TV
TECHNICIAN FOR HELP
CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY
APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE
COULD VOID THE USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.
THIS CLASS B DIGITAL APPARATUS COMPLIES WITH
CANADIAN ICES-003.
CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CONFORME
A LA NORME NMB-003 DU CANADA.

iv KCMU000002
05/30/01
WARNING
•TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
•DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION
GRILLS.
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instruction in
the literature accompanying the product.

v KCMU000002
05/30/01
IMPORTANT SAFEGUARDS
1. READ INSTRUCTIONS – All the safety and operating instructions should be
read before the unit is operated.
2. RETAIN INSTRUCTIONS – The safety and operating instructions should be
retained for future reference.
3. HEED WARNINGS – All warnings on the unit and in the operating
instructions should be adhered to.
4. FOLLOW INSTRUCTIONS – All operating and use instructions should be
followed.
5. CLEANING – Unplug the unit from the outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. See
cleaning procedures under Maintenance.
6. WATER AND MOISTURE – Do not use this unit near water or in an
unprotected outdoor installation, or any area which is classified as a wet
location.
7. ACCESSORIES – Do not place this unit on an unstable stand, tripod,
bracket, or mount. The unit may fall, causing serious injury to a person and
serious damage to the unit. Use only with a stand, tripod, bracket, or mount
recommended by the manufacturer, or sold with the product. Any mounting
of the unit should follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
8. POWER SOURCES – This unit should be operated only from the type of
power source indicated on the marking label.
9. GROUNDING OR POLARIZATION – The power supply supplied with this
unit may be equipped with a polarized alternating-current line plug (a plug
having one blade wider than the other). This plug will fit into the power outlet
only one way. This is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
Alternately, this unit may be equipped with a 3-wire grounding-type plug, a
plug having a third (grounding) pin. This plug will only fit into a grounding-
type power outlet. This is a safety feature. If you are unable to insert the
plug into the outlet, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the grounding-type plug.

vi KCMU000002
05/30/01
IMPORTANT SAFEGUARDS
10. POWER-CORD PROTECTION – Power supply cords should be routed so
that they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
11. Overloading – Do not overload outlets and extension cords as this can
result in a risk of fire or electric shock.
12. Object and Liquid Entry – Never push objects of any kind into this unit
through openings as they may touch dangerous voltage points or short-out
parts that could result in a fire or electric shock. Never spill liquid of any kind
on the unit.
13. Servicing – Do not attempt to service this unit yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
14. Damage Requiring Service – Unplug the unit from the outlet and refer
servicing to qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician
to restore the unit to its normal operation.
e. If the unit has been dropped or the enclosure has been damaged.
f. When the unit exhibits a distinct change in performance - this indicates
a need for service.
15. Replacement Parts – When replacement parts are required, be sure the
service technician has used replacement parts specified by the manufacturer
or have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other hazards.
16. Safety Check – Upon completion of any service or repairs to this unit, ask
the service technician to perform safety checks to determine that the unit is
in proper operating condition.
17. Lightning – For added protection of this unit during a lightning storm, or
when it is left unattended and unused for long periods of time, unplug it from
the wall outlet and disconnect the cable system. This will prevent damage to
the unit due to lightning and power-line surges.

vii KCMU000002
05/30/01
TABLE OF CONTENTS
SECTION 1: INTRODUCTION...............................................................1
PRODUCT DESCRIPTION...............................................................1
FEATURES .......................................................................................1
SECTION 2: CONTROLS AND CONNECTIONS...................................3
CAMERA – FRONT / BACK..............................................................3
CAMERA – TOP / BOTTOM.............................................................4
CAMERA – SIDE...............................................................................4
SECTION 3: INSTALLATION AND ADJUSTMENT ..............................5
CONTENTS OF PACKAGE ..............................................................5
BASIC INSTALLATION.....................................................................6
MANUAL IRIS LENS ADJUSTMENT (OPTIONAL LENS) ...............9
DC TYPE AUTO IRIS LENS INSTALLATION AND
ADJUSTMENT (OPTIONAL LENS)................................................10
BACKFOCUS ADJUSTMENT.........................................................11
AUDIO DEFEAT ADJUSTMENT ....................................................12
SECTION 4: TROUBLESHOOTING AND MAINTENANCE ................14
TROUBLESHOOTING ....................................................................14
PREVENTIVE MAINTENANCE ......................................................15
SPECIFICATIONS ..........................................................................16

viii KCMU000002
05/30/01
THIS PAGE INTENTIONALLY LEFT BLANK.

1 KCMU000002
05/30/01
SECTION 1:
INTRODUCTION
PRODUCT DESCRIPTION
The KC33W4MM camera is a high performance
1/3" black-and-white observation camera designed for
use with Ultrak observation systems. It provides a
low-cost solution for closed-circuit television (CCTV)
and security surveillance applications.
FEATURES
The KC33W4MM camera includes the following
features:
•1/3" CCD Image Sensor – A professional-level
camera chip that achieves a very high quality
picture.
•4mm Fixed Focus Lens
•Support for Standard CS- or C-mount Lens
•Electronic Iris – Automatically adjusts the
camera for changes in lighting to ensure an
optimal picture at all times.
•Microphone – Allows for the monitoring of audio
at the camera location.
•Audio Defeat Switch – Allows the audio feature
of the camera to be disabled. This is important in
states or cities that do not allow audio monitoring
and recording.

2 KCMU000002
05/30/01
FEATURES, CONTINUED
•Interphone Input – Allows for accessory
connections, such as motion sensors, alarm
contacts and two-way intercom boxes.
•Camera Stand/Mount – Allows the camera to be
mounted to shelves, walls, ceilings and many
other structures.
•Excellent Picture Quality
•Single Cable – One cable transmits all
information including video, audio and alarm
signals.
IMPORTANT:
•To reduce the risk of fire or electric shock, do
not expose this product to rain or moisture.
•The KC33W4MM camera may be used in
outdoor settings only when used with
approved camera housing. Contact your
sales representative for information.
•The KC33W4MM camera should never be
used outdoors without a housing.
•The user of this equipment is responsible for
checking and complying with local, state, and
federal laws and statutes concerning the
recording and monitoring of audio signals.

3 KCMU000002
05/30/01
SECTION 2:
CONTROLS AND CONNECTIONS
CAMERA – FRONT / BACK
FRONT BACK
3
2
1
IRIS LEVEL
EI
OFFON
MONITOR INTERPHONE
7
46 5
1 Backfocus Ring Used to adjust the focus of the lens.
2 Back-focus Lock
Screw
Used to secure the backfocus setting.
3 Microphone Gathers sound at the camera location
and transmits the sound to the
monitor.
4 EI Switch Used to turn the electronic iris
function ON or OFF.
5 Monitor Port Used to connect the cable from the
monitor.
6 Interphone Port Used to connect optional accessories.
Up to two alarming devices may be
connected to each camera with the
purchase of an optional two-way
connector. Motion sensors, alarm
contacts, and two-way intercom
boxes can also be connected to this
port. Contact your sales
representative to purchase optional
accessories.
7 Iris Level Control Used to adjust the picture for optimal
quality when used with a DC iris lens.

4 KCMU000002
05/30/01
CAMERA – TOP / BOTTOM
TOP BOTTOM
8
1
8
8 Mounting Hole with 1/4"
– 20 UNC Threads
The camera stand screws into
this hole.
CAMERA – SIDE
9
9 DC Iris Lens Port Used to connect a DC iris lens.

5 KCMU000002
05/30/01
SECTION 3:
INSTALLATION AND ADJUSTMENT
CONTENTS OF PACKAGE
Installation of the KC33W4MM camera must be
performed in accordance with all local and national
electrical and mechanical codes.
Carefully remove the camera and its accessories from
the carton and verify that they were not damaged in
shipment.
The contents of the package include:
1. Black-and-white CCD camera with CS-mount
2. Fixed focus 4mm lens (KOAL04MM)
3. Connector (for DC type auto iris lens)
4. C-mount adapter
5. Camera stand/mount
6. 60-foot camera cable
7. User Manual

6 KCMU000002
05/30/01
BASIC INSTALLATION
After unpacking and identifying the package contents,
perform the following steps to connect the camera to
an observation system.
1. Locate the following items which may be needed
during installation but are NOT supplied with the
KC33W4MM camera.
•Observation monitor
•Welder’s glass
•Mounting hardware
•Tools
2. Select a suitable location for the camera, noting
that the supplied camera cable is 60 feet long.
IMPORTANT: If installing the camera more than
60 feet from the monitor, contact your sales
representative to purchase longer cables.
3. Test each camera and cable at the monitor
location prior to mounting the cameras and
running cables.
4. Use a suitable fastener and necessary tools to
mount the camera stand to a structural object,
such as a wall stud, shelf, or ceiling rafter, that
can support the weight of the camera and mount.
IMPORTANT: The maximum recommended load
of the mounting bracket is 11 lbs (5kg).

7 KCMU000002
05/30/01
BASIC INSTALLATION, CONTINUED
5. The KC33W4MM observation camera has a
1/4" – 20 UNC mounting hole located at the top
and the bottom of the camera housing. Mount the
camera on the stand by threading the camera
onto the mounting bolt. Adjust the camera’s
position and tighten the wing nut to hold the
position firmly in place.
REMINDER: Do not aim or point the camera
towards the sun or into a strong light.
6. The KC33W4MM camera supports both
C- and CS-mount lenses. The KAOL04MM lens
supplied with the camera is a CS-mount lens.
When using a CS-mount lens, attach the lens
directly on the backfocus ring.
Backfocus Lock Screw
Backfocus Ring
Camera Mounting Bracket
C-Mount Adapter
(
C-MOUNT LENS
)
( CS-MOUNT LENS )
OR
When using a C-mount lens, attach the C-mount
adapter to the backfocus ring before attaching the
C-mount lens.

8 KCMU000002
05/30/01
BASIC INSTALLATION, CONTINUED
7. The KOAL04MM
lens supplied with
the camera is a
DC type fixed focus
lens. No additional
connections are
required. DC Iris Lens Connector
If using a DC type auto iris lens, plug the cable
into the DC lens connector.
8. Route the cable from the monitor location to the
camera location.
IMPORTANT: Care should be taken when
routing the cable from the monitor to the camera.
Try not to put unnecessary strain on the cable or
connectors. Do not place the cable next to
fluorescent lights as interference may result. Do
not use staples to support the cable as they may
damage the cable. If the provided camera cable
is not long enough, do not substitute a telephone
cable as it could damage the camera and/or the
monitor. Contact your authorized sales
representative to purchase longer cables.
9. Plug the cable into
the connector port
labeled MONITOR on
the back of the
camera.
IRIS LEVEL
EI
OFFON
MONITOR INTERPHONE
MONITOR port

9 KCMU000002
05/30/01
BASIC INSTALLATION, CONTINUED
10. Plug the other end of the camera cable into the
CAMERA port on the back of the monitor.
11. Plug the monitor’s power cable into a suitable wall
outlet.
12. Turn the monitor ON. The monitor should display
images for the connected camera(s). For more
information on system installation and camera
display options, refer to the observation monitor or
system manual.
13. Adjust the lens focus and iris control for an
optimum picture.
MANUAL IRIS LENS ADJUSTMENT (OPTIONAL LENS)
A manual iris lens is used in indoor applications where
lighting from windows can considerably affect the light
level of the room. When using a manual iris lens,
perform the following:
1. Set the EI switch to ON.
2. Turn the iris ring on the lens to the fully open
position.
3. Focus the lens to obtain optimum picture.
4. To increase the camera’s depth of field, slightly
close the manual iris by approximately 5-10%.

10 KCMU000002
05/30/01
DC TYPE AUTO IRIS LENS INSTALLATION AND
ADJUSTMENT (OPTIONAL LENS)
The KC33W4MM camera supports DC auto iris
lenses. Perform the following steps to install and
adjust a DC type auto iris lens:
1. Thread the DC iris lens onto the lens mount on
the front of the camera.
2. If using an Ultrak lens, skip to step 3.
If using a non-Ultrak lens, use the manufacturer’s
instructions to solder the connector supplied with
the camera to the lens control wires. The pin-out
and wire color-coding for DC type auto iris lenses
can vary from one manufacturer to another.
3. Plug the connector into the DC iris jack on the
side of the camera. The connector is keyed and
can only be inserted into the jack one way.
4. Make sure that the EI switch located on the back
of the camera is set to OFF.
5. Apply power to the camera.
6. Adjust the DC type auto iris lens for an optimum
picture using the IRIS LEVEL control on the back
of the camera.

11 KCMU000002
05/30/01
BACKFOCUS ADJUSTMENT
Although the camera backfocus was adjusted by the
manufacturer prior to shipping, it may be necessary to
make modifications.
For best results, perform backfocus adjustments at
night or while using a #6 or #8 welder’s glass in front
of the lens. The focus of the camera will change
slightly if the camera iris was adjusted on a light scene
and then changes to a dark scene. However, the
camera will remain in focus if the iris was focused on
a dark scene and the scene lightens.
To make backfocus adjustments, perform the
following:
1. Mount the lens on the camera and apply power.
2. Open the camera iris by turning the lens level
control counterclockwise.
3. If a picture is visible, focus on the scene.
Open the lens as wide as possible by placing a
welder’s glass in front of the lens.
4. When the iris is open to the widest point, readjust
the focus for a clear picture. If a clear picture is
not visible, set the focus ring to mid-range.
5. Loosen the backfocus lock screw.
6. Adjust the backfocus ring for a clear picture.
7. Tighten the backfocus screw lock.
8. Fine-tune the focus with the focus ring on the lens.
9. Remove the welder’s glass from in front of the
lens.
10. Adjust the level control of the lens for the best
picture quality.

12 KCMU000002
05/30/01
AUDIO DEFEAT ADJUSTMENT
It may be necessary to disable the audio from the
camera to comply with some state and local laws and
regulations.
To disable audio, perform the following:
1. Turn the monitor’s main power switch OFF.
2. Remove the camera from the camera stand.
3. Disconnect the cable(s) from the back of the
camera.
4. Remove the two screws on top of the camera.
5. Remove the top half of the camera case.
6. If an intercom station is not used:
Locate the audio disable jumper on the right back
portion of the camera. Remove the audio jumper
using needle-nose pliers. Replace the jumper on
the center pin and the OFF pin, as illustrated.
A
UDIO
OFFON
Move the jumper from the ON and
center position to the OFF and
center position to disable the
audio from the camera to the
observation monitor.