UNITED HC7235 User manual

Rechargeable Hair Clipper
Model No.: HC7235
Instruction Manual
Please read these instructions carefully. Pay your special attention to important safety
instructions. Keep this “Instructions for use” for future reference.

Safety instructions and recommendations
Herewith information concerns your health and safety. It is obligatory to learn about
all instructions for use and safety information before first usage of the clipper.
The hair clipper is intended for domestic use. In case it is used for commercial
use, the guarantee conditions change.
Connect the power supply adaptor to AC mains supply 100-240 V.
Disconnect the power supply adaptor from the mains supply outlet when not in
use or before cleaning.
Do not unplug pulling by the cord.
The supplying cord should not hang over the edge of a table or desktop, nor touch
hot surface.
If the non-detachable part of the cord is damaged, it should be replaced by the
producer or at a proper service point or by a qualified person in order to avoid any
hazards.
This device is intended for cutting natural hair, only. It is allowed to use it only
for human hair; it cannot be used for cutting artificial or animal hair. Using the
product for other than intended purposes shall cause nullifying the guarantee.
Do not touch the power supply adaptor with wet hands, especially when plugging
or unplugging it from the mains supply outlet.
For the operation with mains use only the adaptor supplied with the hair clipper.
Connect only to easily accessible mains supply outlet.
Do not cover the adaptor; it can lead to dangerous temperature increase.
Do not use during bath.
Never immerse the device and cord in water or other liquids.
Do not place the hair clipper on wet surface or cloth during operation.
Do not place or store the device in the area where it can fall into water.
Do not use the device with damaged comb attachment. It can cause injuries
hazard.
Never try to remove the foreign bodies out of the clipper using sharp objects (i.e.
comb).
Always clean after using.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience –– and
knowledge,.
Children should be supervised to ensure that they do not play with the appliance.
Do not apply not recommended attachments.
The hair clipper can be used both as a mains and cordless device.
The cut hair should be clean, dry and combed.
Put the towel around the neck to avoid getting the cut hair under the collar.
Use the hair clipper only as intended according to the herewith instructions.

WARNING: Do not use the device near water, over the bath tube,
pool or other water basin.
WARNING: Observe the above mentioned rules in order to avoid
burning, electric shock or fire hazard.
Make sure you understood the instructions.
Description of the Parts
1. Cutting head
2. Thinning function knob
3. On/off Switch
4. Charging light
5. Combs : 3/6/9/12/15mm & 18/21/24/27/30mm
6. Power supply adapter
7. Cleaning brush
8. Blade oil
9. Barber comb
10. Scissors
Handling and operation of hair clipper
The hair clipper can be used both as a mains supplied or cordless device.
1. Operation with power supply adaptor
At first insert the adaptor plug into the device and then insert the adapter plug into the
mains supply outlet (100-240 V). In mains supplied mode the device is ready for use.
2. Loading accumulators and cordless operation
1
2
3
4
5
6
7
8
9
10

TIP: Load the device minimum 12h before first usage and when 2–3 next loadings.
In order to load the device moving the ON/OFF switch to „OFF” position.
Insert the plug of the adapter into appropriate mains supply outlet (100-240 V). The
loading process is indicated by red pilot light glowing. When fully loaded the hair
clipper can operate approximately 60 minutes.
The hair clipper accumulator obtains optimum power after three cycles of loading
and unloading. 8 hours is enough for next loading. In order to –– provide long life
of accumulators, they should be completely unloaded before loading.
3. Using the clipper for hair cutting and thinning
TIP: Cut the hair for demanded length in stages, start form bigger length.
Insert appropriate comb attachment.
Set the desired length of hair/beard. The length of clipped hair is indicated (In
millimeter) at the length indicator on the comb attachment.
Turn on the device on and Cut only small areas.
Move the clipper slowly along hair.
Hold the device so, that the comb attachment is laid flat.
Always start the cutting from the neck upwards or from the forehead and temples
upwards to the top of head.
In order to thin the hair, turn the hair thinning knob to the left position; the thinning
attachment integrated with cutting head shall be moved up from the housing.
You can reduce the hair volume with this feature. It provides a modern, changed look
without the change of hair length.
4. Cutting hair without attachment
WARNING: The cutting head (1) is very sharp. Injury hazard!
You can cut the hair in uniform length of 1–2 mm without comb attachment.
For clipping the hairline of bristle and whiskers, neck shaving:
Move the hair clipper slowly along hair.
Turn the device so, that the back part was directed upwards.
Place the edge of the cutting head without comb attachment on desired length of
bristle hairline.
Move down the clipper in operation.
5. Comb attachments inserting/replacing
It is possible to select one of two comb attachments:
The small attachment can cut hair for the length of: 3 mm, 6 mm, 9 mm, 12 mm, and
15 mm.

The big attachment can cut hair for the length of: 18 mm, 21 mm, 24 mm, 27 mm, and
30 mm.
Select the attachment according to the length of cutting.
Insert it into the side guiding grooves of the clipper.
Replace one attachment removing it and inserting another as described above.
Cleaning and maintenance
Do not hold the adaptor with wet hands while plugging and unplugging form mains
supply outlet.
The adaptor and supplying cord should be always dry.
It is forbidden to immerse the hair clipper in water or other
liquids for cleaning, as the device is not waterproof. It can
damage the live parts (accumulators).
Always switch off the hair clipper and unplug the adaptor from
the mains supply outlet before cleaning and ––maintenance.
Remove the comb attachment from the hair clipper.––
In order to remove the cutting head, press forward cutting head
with your thumb, in order to release the cutting head from the
frame.
If necessary, rinse the plastic comb attachments under running
water, and then dry them thoroughly.
Remove the remains of hair from the cutting head with attached
cleaning brush.
Insert the protrusion of cutting head back into the locking hole in the frame of cutting

head.
Press gently the cutting head in, until you hear a clicking sound of locking.
TIP: In order to reduce friction, from time to time insert one or two drops of oil
between the blades and distribute it evenly.
You can use any kind of acidless oil (such as oil for sewing machine). Remove the
exceeding oil with cloth.

NOTICEABOUT RECYCLING
Your product is designed and manufactured with high quality materials and
components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of-life,
should be disposed of separately from your household waste. Please dispose of this
equipment at your local community waste collection/ recycling centre.
In the European Union there are separate collection systems for used electrical
and electronic products. Please help us to conserve the environment we live in!
DECLARATION OFCONFORMITY
This product complies with the requirements of the directives
EMC-Directive: 14 /30 / EU
Low Voltage Directive: 14 / 35 / EU
ROHS2 Directive: 11 / 65 / EU
EXCLUSIVE IMPORTER IN GREECE:
Amiridis – Savvidis S.A.
Bystreet 87, 17th November Str. – P.C. 55535
Pylaia – Thessaloniki – Greece
Tel: [phone]
www.amiridis-savvidis.gr
www.united-electronics.gr