Unitone UNI-VM7-BL User manual

UNI-VM7-BL \ UNI-VM7-WL
USER MANUAL - IP 660
Ver.081519

Messages
Views
……………………………………………………4
TABLE OF CONTENTS
……………………………………………………5
……………………………………………………6
……………………………………………………7
……………………………………………………8
……………………………………………………9-10
Introduction
……………………………………………………3

UNI-VM7-BL \ UNI-VM7-WL Getting to know the indoor monitor
Introduction
7'' capacitive touch screen
Speaker
Hands free
Reserved
Calling management center
Monitoring
Unlocking
Microphone
CPU ARM Corex-A7 1.2 GHz
MEMORY 64MB DDR2 SDRAM
FLASH MEMORY 128MB NAND
OPERATION SYSTEM Linux
WIRING TYPE 2wire
POWER DC 48v over 2wire
RATED POWER 7W
STANDBY POWER 3W
CAMERA No
RESOLUTION 800 X 480
DISPLAY 7" TFT LCD
AUDIO CODEC G.711
VIDEO CODEC H.264
PROTOCOL SIP, TCP/IP, RTSP
IP CAMERAS SUPPORT Up to 8 cameras
ALARM Spports up to 8 zones
DOOR BELL SUPPORT Yes
COLOR Black \ White
SIZE 235 X 145 X 19.5

To view extra long message: Press the message line twice
To scroll: Use the up or down arrows
To delete: Click on desired message and press
To go back: Press
Messages
Press to view messages (screen below will appear)
Messages
NOTE: Indoor monitor can store a maximum of 64 messages
1 FedEx package is waiting for you at the concierge desk 06/25/19
2 UPS package is waiting for you at the concierge desk 06/24/19
3 MAINTANENCE – No hot water on 06/30/19 bet 10:30… 06/21/19
4
5
Messages

Views
Views
Press to monitor camera views and outdoor stations
(screen below will appear)
Press To monitor outdoor call panels
Press To see cameras views
Press to go back
Door1
Click “Left” or “Right” to select
view. Click to start, Click to
stop.
“Monitor” “Camera”
Click “Left” or “Right” to select
view. Click to start, Click to
stop.
Click to unlock door.
Views

To scroll: Use or
To delete: Click on desired call and press
Press to view visitor’s snap shot (if taken)
Press to listen to voice message (from APT caller or Call Panel)
Calls
Press to view recent calls (screen below will appear)
Calls
NOTE: Indoor monitor can store a maximum of 64 calls
Refers to outgoing calls
Refers to incoming calls
Refers to missed calls
Calls

Security
Press to turn the alarm on or off (screen below will appear)
Security
To arm the system: Choose the desired profile to activate sensors.
The chosen icon will turn Red and will emit “beep beep”.
Note: System has a built-in delay time before sensors are activated (delay time is
configured in settings).
To disarm the system: Press “off.” Password box appears. Input password.
(Default password is 1234 and can be changed in “settings” menu.)
Note: You can disarm the system during the built-in delay time without having to input a
password.
When alarm sensor is triggered, the indoor monitor will emit a loud alarm,
and the and the screen below will appear. An alarm will be sent to the
management center (if management center is installed):
O
K
You can see the sensor No. and type in Red, shown at the top of the
screen. For example, “2: Smoke” indicates that a smoke sensor in zone 2 is
triggered. To stop alarm, input the password (the default password is 1234).
Security
* Will be available if building is equipped with integrated alarm / smoke sensors.
(Optional) *

Press to call concierge
Concierge
Concierge
To call other apartments press (screen below will appear)
Dial the APT code followed by
Concierge
Call APT.
Mute
Press to mute (icon will turn Red)
Press to unmute (icon will turn back to normal)

Press to enter “settings” (screen below will appear)
To raise or lower the volume, tap on the volume bar. Press OK to store
changes.
Note: “Volume” changes the sound level for all alerts and alarms.
“Intercom” changes the sound level of all conversation.
To adjust the time zone: click on adjacent box. Keypad will appear. Input
desired time. Press OK to store changes.
To use auto answer, check the “auto answer” box.
Press OK to store.
Note: When auto answer box is checked, calls will be answered automatically after one ring.
To activate voice message, check box.
Note: Messages are recorded and logged on monitors when residents are unavailable.
Note: “Room”, “Network”, “Admin PWD”, “Zone” and “Version” in the settings
menu are designated for technicians only.
Settings

To change the user password, Click on “User PWD” (screen below
will appear)
Put in the old password (Default password is 1234). Input new
password. Confirm new password. Press OK to store.
To change the alarm zone profiles, Click on “Scene” (screen below will
appear)
To change the built-in delay time, click on “Activation time” and
select desired time. Press OK to store.
To adjust the alarm profile, check the desired zones according to
the desired profile. Press OK to store.
Settings