Upper Bounce UBRTG01-1017 User manual

UBRTG01-1017, UB03EC-1017E
Model # S
Manual Version #03

13
13
;

INTRODUCTION
must
As with any type of recreational physical activity, without being careful participants can be injured.
8m

TRAMPOLINE GUIDELINES
5
U
Beware that when using tools or doing technical work there is always a risk of injury; therefore
assemble the product carefully.
,

24 ft

LEG SUPPORT
SHORT
CORNER
SUPPORT
SUPPORT
LEG BASE
SCREWS
COVER
PADS
JUMPING
MAT
11.8
LEG SUPPORT
LONG
MIDDLE SUPPORT
LEG
EXTENSION
CORNER
TUBE
59.8
TRAMPOLINE PARTS LIST FOR UBRTG01-1017
ATOP RAIL A
C1
C2
LEG BASE
SPRINGS
31.5
WASHER
B TOP RAIL B
C
E
F
G
H
ITOP RAIL SCREWS
& NUTS
J
K
LSPRING PULLING
TOOL
M
N
O
P
Q
UBRPTR1-1017
UBRPTR2-1017
UBRPTR3-1017
UBRPCT1-1017
UBRPCT2-1017
UBRPLE-1017
UBRPL1-1017
UBRPM-1017
UBRPP-1017
UBHWD-SP-7
UBRPRS-1017
UBRPSW-1017
UBRPSW-1017
UBHWD-TH
UBRPSN-1017
UBRPLS1-1017
UBRPLS2-1017
UBRPL2-1017
2
2
2
2
2
10
4
1
1
108
10
22
32
1
8
2
4
2
1
UBRPN-1017
D
C1

3. Assembling the center Leg Base.
4. Assembling the frame to the Base.
Take part #Q and insert it between the 2 part #N pieces, secure
together with screws and washers part #J and K. (Connect it to
the longer side of the part #N.) Attach the 2 parts #D onto both
part #N pieces, secure together with screws and washers part
#J and K.
Attach the 2 parts #A to both sides onto part #D of the middle
leg base. Lay the assembled part on the ground.
Attach the leg extensions to the leg base and tightly secure together
with screws and washers Part #J and K. Continue doing the same to
all 4 leg bases.
Q
NN
D
J
K
K
J
K
D
K
O
P
2. Connect the middle leg supports to the legs.
E D
D
N
Q
N
DA
A
Frame assembly installation for model UBRTG01-1017
MM
B1
45.3
44.88
B2
45.3
B1
44.88
B2
Connect part #P and part #O together. Once they is attached, connect
the pole to the legs by inserting it between part #D leg extensions.
Secure
it to the legs with screws part #M, (The part #P and part #O
should be placed 16” above the ground.) Continue doing the same
to all 4
legs bases.
t
B

7. Connect the base.
Secure the frame pieces together using the screws and nuts part #I.
Make sure to tighten the screws.
6. Attach all the corners.
Attach the corners to the frame, make sure the
longer side of part #C is on the longer side of the
trampoline as the picture shows.
5. Assemble frame parts B1 and B2 with the 4 legs.
Lay out the parts as shown in the figure. Connect the B1 and B2 and place onto the leg bases as shown
in the figure below.
10
8. Then secure top rails to the leg base using screws J and washers K
as shown in figure, and repeat this step to all legs.
C1
C1
A
A
C2
C2
A
A
B2
B1
B1
B2
E
E
E
E
N
N
Q
N
N
Q
E
D
E
E
E
P
O
O
P
O
P
D
D
O
D
O
PD
P
O
P
B1
B2
B1
B2
1. Part #A goes on the long side of the trampoline - the 17 ft side.
2. Make sure that all screw holes that connect the B rails to the legs are
facing the inside of the frame.
Note: