US Polymers DURAMAX Metal Garden Eco Shed User manual

OWNER’S MANUAL /
Instructions for Assembly
Size 8 Ft x 8 Ft / 2.6 m x 2.4 m
Customer
Service Hotline
[phone]
www.duramaxbp.com
• Tall Walk in Shed
• Quick & Easy Assembly
• Ridge Reinforced Walls
• Wide Double Doors
• Available in Various Sizes
Call us for any missing or damaged parts.
Do not return to the store.
ALL PURPOSE METAL STORAGE SHEDS
Ver: 0.0
Metal Garden Eco Shed
Metal Garden Eco Shed
All manuals and user guides at all-guides.com

Duramax Storage Shed
Limited Fifteen Year Warranty
U.S. Polymer Inc. will send a replacement part free of charge, in the event of material defects and or
workmanship for a period of fifteen years from the date of purchase.
This warranty is extended only to the original purchaser. A purchase receipt or other proof of date of original
purchase will be required before warranty service is rendered. In no event shall we pay the cost of flooring,
labor, installation or any other costs related thereto.
This warranty only covers failures due to defects in material or workmanship which occurs during normal
use and does not extend to color change arising due to normal weathering or to damage resulting from
misuse or neglect, commercial use, failure to follow assembly instructions and the owner’s manual (including
proper anchoring of the shed), painting, forces of nature and other causes which is beyond our control.
Claims under this warranty must be made within the warranty period by calling 1-800-483-4674 or mail in
a dated sales slip and clear photograph of the part to:
U.S. Polymers, Inc.
1057 S. Vail Ave,
Montebello, CA 90640
We reserve the right to discontinue or change components. If a component has been discontinued or is
not available,
U.S. Polymers, Inc. reserves the right to substitute a component of equal quality as may be compatible.
Limits and Exclusions
There are no express warranties except as listed above. The warrantor shall not be liable for incidental or
consequential damages resulting from the use of this product, or arising out of any breach of this warranty.
All express warranties are limited to the warranty period set forth above. Some states do not allow the
exclusion or limitation on how long an implied warranty lasts, so the above limitations may not apply to
you.
This warranty gives you specific legal rights and you may also have other rights which vary from state to
state or country to country.
All manuals and user guides at all-guides.com

IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
Note: Check all parts prior to installation.
CODE QTY
BLB 1
BRB 1
BS1A 2
BS2A 2
BBF 2
ECB 1
DCL 1
DCR 1
ABLB 1
ABRB 1
AS1A 2
AS2A 2
SCB 1
SSB 1
SLB 1
SRB 1
RS1J 4
RS2J 4
SB1E 2
SB2E 2
RF1B 2
RF2B 2
RFSA 4
RFCA 2
TSLB 1
TSRB 1
BSLB 1
BSRB 1
DSS 2
DSCB 4
GPVE 2
GPS 2
WSE 8
WCFE 2
WCBE 2
WFLE 2
WFRE 2
GPLE 2
GPRE 2
RP1J 2
RP2J 2
RP3J 2
RP4J 2
DPLB 1
DPRB 1
ACCESSORIES
CODE QTY
BS 4
DH 2
FC 2
TC 4
TS 4
VC 4
PW 3Slabs
PC 3Slabs
WST 2.8 MTR
S1 197
S2 111
S3 105
Parts List
Hand Gloves
Cordless Drill - Philips Head
Screw driver - Philips Head
Carpenters Square
Eye Protector
8’ Step Ladder
Adjustable pliers
Level - 3 ft.
Tape Measure
Tools You Will Need
SB1E, SB2E
BBF
BLB,BRB
BS1A,BS2A
PROFILES
RFCA
ABLB,ABRB
RF1B,RF2B
RFSA
RS1J, RS2J
SLB, SRB
AS1A,AS2A
SCB
SSB
DCL
DCR
ECB
TSLB, TSRB, BSLB,
BSRB
DSS, DSCB,
GPS
ACCESSORIES
FC VC
S3
PC
TC
DH
BS
S1, S2
TS
WST
PW
Note - Use screws with plastic washers
on top of prepainted surface only.
All manuals and user guides at all-guides.com

IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
Exploded View
RFCA
RP3J
RP2J
AS2A
AS1A
BS1A
BS2A
RFSA
RFSA
BLB
BRB
BBF
BBF
BS1A
BS2A
ECB
WFRE
WFLE
WCFE
WCFE
WCBE
WCBE
DCL
DCR
DPLB
DPRB
SCB
ABRB
ABLB
AS1A
AS2A
SLB
SRB
SSB
GPLE
GPRE
GPS
SB1E
SB2E SB2E
SB1E
RS1J
RS2J
GPLE
GPRE
RF2B
RFSA
RF2B
RF1B
RF1B
RFSA
RFCA
RP4J
RP3J
RP1J
RP4J
RP2J
RP1J
RS1J
RS2J
GPVE
GPVE
WSE
WSE WSE
WSE
WSE
WSE
WSE WSE
All manuals and user guides at all-guides.com

A. Foundation
S2
FC2B
FC1B
Parts needed:
FC1B 2
FC2B 2
FC3A 2
FC4A 2
FC5A 4
FC6A 4
FC5B 9
S2 85
CODE QTY
1
FC3A
FC4A S2
23
FC5A S2
FC6A
4
1
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
6
U-Channel Position
FC3A
FC4A
FC2B
FC1B
FC1B FC4A
FC3A
FC2B
S2
Make 2 sets.
Make 2 sets. Make 4 sets.
FCC
FCC
FCC
FCC
S2
5
7
FC6A
FC5A
FC6A
FC5A
FC6A
FC5A
FC6A
FC5A
U-Channel Position
FC5B
FC5B
FC5B
FC5B
FC5B
FC5B
FC5B
FC5B
FC5B
All manuals and user guides at all-guides.com

2
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
Fig.2
S1
Take care of sharp edges.
Use screws with plastic
washers on top of prepainted
surface only.
Note
S1
Fig.2
Fig.1
BLB
BRB
Fig.1
Parts needed:
BLB 1
BRB 1
BS1A 2
BS2A 2
BBF 2
ECB 1
S1 12
S2 22
CODE QTY
BLB
BRB
1 & 2
B. Base Frame
Note It is important that these instructions
are followed step by step.
Don’t install under windy conditions.
1
2
BS1A
BS2A
1 & 2
BS1A
BS2A
BS1A
BS2A
Make two sets.
All manuals and user guides at all-guides.com

3
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
S2
3
4
5
S1
Fig.2
BRB
BS1A
Fig.1
S1
BLB
BS2A
BS2A
BS1A
BS2A
BS1A
Fig.2
S2
BS1A
Fig.1
S2
BS2A
BLB
BRB
Front
Right
Left
Back
BS1A
BS2A BLB
BRB
BS2A
BS1A
2
1
1
2
All manuals and user guides at all-guides.com

4
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
6
7
8
Fig.2
S1
Fig.1
BBF
BS2A
S2
BBF
BBF BS2A
1 & 2
1 & 2
BS1A
BBF
BBF
2168mm
971mm
971mm
490mm
All manuals and user guides at all-guides.com

5
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
All panels are clearly marked
and care should be taken to
use the correct one.
Note
WFRE 1
WFLE 1
WCFE 2
WCBE 2
WS 6
SRB 1
SLB 1
AS1A 2
AS2A 2
SSB 1
SCB 1
TS 4
DCL 1
DCR 1
ABLB 1
ABRB 1
PW 83
S1 87
S3 12
CODE QTY CODE QTY
Parts needed:
IMPORTANT:
Note
Use screws with plastic washers on
top of prepainted surface only.
S3
PW
S1
PW
C. Walls & Columns
S2
9
Fig.2
S2
Fig.1
ECB
BBF
S1
WFRE
BBF
PW
1
Right
Front
ECB
BBF
BBF
All manuals and user guides at all-guides.com

6
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
Make sure the overlapping
position is as shown in fig.1.
Note
PW
BBF BS2A
S1
Fig.2
Fig.1
2
BS1A
BS2A
1
2
Front Right
PW
S3
3
Fig.2
SRB
S1
PW
Fig.1
4
SRB
1 & 2
Front
WCFE
WCRE
WCRE WCFE
WCRE WCFE
WCRE WCFE
WCFE
WCFE
All manuals and user guides at all-guides.com

7
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
Make sure the position of the
projection on (TS) towards
inside.
Note
SRA
TS
Front
5
SRB
Front
S1
BBF PW
6
Front
BBF
Left
Make sure the overlapping
position is as shown in fig.1.
Note
Fig.1 Fig.2
S1
BBF PW
Front
Left
1
2
7
WCRE
WCLE
WCLE
WCLE
WCFE
BS1A
BS1A
WCLE
WCFE
All manuals and user guides at all-guides.com

8
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
Front
Left
S3
PW
1 & 2
SLB
Front
Fig.2
S1
PW
Fig.1
SLB
8
9
Make sure the position of the
projection on top slider
towards inside.
Note
Front
SLB
Front
SLB
TS
10
WCLE
WCFE
WCLE
WCLE
All manuals and user guides at all-guides.com

9
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
SLB
SRB
SSB
1 & 2
Front
Fig.1
SLB
SRB
SSB
Fig.2
SRB
SSB
SLB S1
11
PW
S1
BS2A
12
Make sure the overlapping
position is same as shown in
fig.1.
Note
Fig.1
WS Fig.2
S3
PW
Fig.3
S1
PW
BLB
13
1
2
3
Back
Left
Back
Left
WCBE
WCBE
WCBE
WCBE
WSE
All manuals and user guides at all-guides.com

S1
SLB
Left
10
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
Top angle (AS1A) must slide in
between the sliding channel (SLB)
and wall panel (WCFE).
Note
Fig.2
S1
PW
ABLB
Fig.1
ABLB
14
ABLB
1 & 2
Left
Back
15
Top angle (AS2A) must sit on
top angle (ABLB).
Note
Back
Left
Fig.1
ABLB
Fig.2
ABLB
1 & 2
S1
AS2A
ABLB
16
WCBE
AS1A
WCFE
AS1A
WCFE
WCBE
WCBE
WCBE
AS2A
AS2A
WSE
PW
SLB
PW
All manuals and user guides at all-guides.com

11
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
Fig.3
S3
PW
Fig.2
S1
PW
Fig.1
S1
PW
AS2A
WS
19
S1
AS1A
AS2A
AS2A
AS1A
17
Fig.1
S1
PW
Fig.2
PW S3
Fig.3
PW S1
18
Make sure the overlapping position of panels is as
shown in fig.1.
Note
Left
1
2
3
Left
1
2
3
3
WCBE
WCFE
WCFE
WCBE
WSE
WSE
WSE
WSE
WSE
WSE
All manuals and user guides at all-guides.com

12
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
Fig.2
ABRB
PW
S1
Fig.1
ABRB
Right
Back
22
S1
BS1A
PW
Right
20
Back
Make sure the overlapping
position of panels is as
shown in fig.1.
Note
Fig.1 Fig.2
S3
PW
21
1
2
Right
Back
S1
PW
BRB
1 & 2
ABRB
WCBE
WCBE
WCBE
BS1A
WCBE
WSE
WSE
WSE
WSE
All manuals and user guides at all-guides.com

13
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
S1
ABRB
ABLB
ABRB
Back
ABLB
23
Top angle must slide in between
the sliding channel (SRB) and
the wall panel (WCFE). See fig.
Note
SRB
S1
PW
Right
Back
24
Top angle (AS1A) must sit
on top angle (ABRA).
Note
Fig.1
ABRA
AS1A
WS
27
Fig.2
AS1A ABRA
WS
AS1A
1 & 2
S1
Right
Back
WCBE
WCFE
AS2A
AS2A
WCFE
WCBE
WCBE
WCBE
PW
All manuals and user guides at all-guides.com

14
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
Make sure the overlapping
position. See fig.1.
Note
Fig.2
S3
PW
S1
Fig.3
PW
Fig.1
ASB
S1
PW
27
1
2
3
Right
Make sure the overlapping
position. See fig.1 & 2.
Note
Fig.2
S1 PW
Fig.1
S1
PW
Fig.3
S3
PW
28
Right
3
3
1
2
WCFE
WCFE
WCBE
WCBE
WSE
WSE
WSE
WSE
WSE
WSE
WSE
All manuals and user guides at all-guides.com

15
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
29
Fig.2
PW
S3
Fig.1
PW
WS S1
Make sure the overlapping
position. See fig.1.
Note
Back
Back
WS
WS
WS
1
2
3
3
1
2
WS
Fig.2
S1
PW
WS
WS
Fig.1
WS
WS PW S1
Fig.3
PW
S3
Make sure the overlapping
position. See fig.1 & 2.
Note
30
2
1
DCL
Fig.1
DCL
BBF
Fig.2
DCL
31
All manuals and user guides at all-guides.com

16
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
SCB
S1
S1
DCL
Front
DCR
Front
Right
DCL
32
SCB
33
All manuals and user guides at all-guides.com