US Stove Company 5660 User manual

851901K-2501F
• Please read this entire manual before installation and use of this appliance. Failure to follow these
instructions could result in property damage, bodily injury, or even death.
• Contactyourlocalbuildingorreofcialsaboutobtainingpermits,restrictionsandinstallationinspection
requirements in your area.
• Save these instructions.
• Ifyourheaterisnotproperlyinstalled,ahouseremayresult.Foreveryone’ssafety,followallInstallation
and Operating Directions. Never use makeshift compromises during the installation of this appliance.
Contactyourlocalbuildingorreofcialsaboutrestrictionsandinstallationinspectionrequirementsin
your area. These Pellet Stove Room Heaters have been designed for use in the US and Canada and are
suitable for mobile homes.
U.S. Stove Company
227 Industrial Park Road, South Pittsburg, TN 37380
1-800-750-2723 www.usstove.com
This unit is not intended to be used as a primary source of heat.
French version is available for download from the United States Stove Company website: http://www.usstove.
com/La version française est disponible pour téléchargement à partir du site United States Stove Company:
http://www.usstove.com/
Installation and Operating Manual
Model 5660
U.S. Environmental Protection Agency
Certiedtocomplywith2015particulateemissions
standards.

2
• IMPORTANT: Read this entire manual before
installing and operating this product. Failure to do
so may result in property damage, bodily injury,
or even death. Proper installation of this stove is
crucialforsafeandefcientoperation.
• Installventatclearancesspeciedbythevent
manufacturer.
• Do not connect the pellet vent to a vent serving
any other appliance or stove.
• Donotinstallauedamperintheexhaustventing
system of this unit.
• Use of outside air is not required for this unit.
• Contactyourlocalbuildingofcialstoobtain
a permit and information on any additional
installation restrictions or inspection requirements in
your area.
• Do not throw this manual away. This manual has
important operating and maintenance instructions
that you will need at a later time. Always follow
the instructions in this manual.
• This appliance is designed for the use of pelletized
fuelthatmeetorexceedthestandardsetbythe
Pellet Fuel Institute(PFI),
• Never use gasoline, gasoline-type lantern fuel,
kerosene,charcoallighteruid,orsimilarliquids
tostartor’freshenup’areinthisstove.Keepall
such liquids well away from the stove while it is in
use.
• A working smoke detector must be installed in the
same room as this product.
• Installasmokedetectoroneachoorofyour
home;incaseofaccidentalrefromanycauseit
can provide time for escape.
• The smoke detector must be installed at least
15 feet (4,57 M) from the appliance in order to
prevent undue triggering of the detector when
reloading.
• Do not unplug the stove if you suspect a
malfunction.TurntheON/OFFSWITCHto”OFF’
and contact your dealer.
• Your stove requires periodic maintenance and
cleaning (see ”MAINTENANCE ”). Failure to
maintain your stove may lead to improper and/or
unsafe operation.
• Disconnect the power cord before performing any
maintenance! NOTE: Turning the ON/OFF Switch
to ”OFF” does not disconnect all power to the
electrical components of the stove.
• Never try to repair or replace any part of the
stove unless instructions for doing so are given in
this manual. All other work should be done by a
trained technician.
• Do not operate your stove with the viewing door
open. The auger will not feed pellets under these
circumstances and a safety concern may arise
from sparks or fumes entering the room.
• Allow the stove to cool before performing
any maintenance or cleaning. Ashes must be
disposedinametalcontainerwithatightttinglid.
The closed container of ashes should be placed
on a non-combustible surface or on the ground,
well away from all combustible materials, pending
naldisposal.
• Theexhaustsystemshouldbecheckedmonthly
during the burning season for any build-up of soot
or creosote.
• Do not touch the hot surfaces of the stove.
Educate all children on the dangers of a high-
temperature stove. Young children should be
supervised when they are in the same room as the
stove.
• The hopper and stove top will be hot during
operation; therefore, you should always use some
type of hand protection when refueling your stove.
• A power surge protector is required. This unit must
be plugged into a 110 - 120V, 60 Hz grounded
electrical outlet. Do not use an adapter plug
or sever the grounding plug. Do not route the
electrical cord underneath, in front of, or over the
heater.Donotroutethecordinfoottrafcareas
or pinch the cord under furniture.
• The heater will not operate during a power
outage. If a power outage does occur, check the
heater for smoke spillage and open a window if
any smoke spills into the room.
• The feed door must be closed and sealed during
operation.
• Neverblockfreeairowthroughtheopenventsof
the unit.
• Keep foreign objects out of the hopper.
• The moving parts of this stove are propelled by
high torque electric motors. Keep all body parts
away from the auger while the stove is plugged
into an electrical outlet. These moving parts
may begin to move at any time while the stove is
plugged in.
• Donotplaceclothingorotherammableitemson
or near this stove.
• When installed in a mobile home, the stove must
be grounded directly to the steel chassis and
boltedtotheoor.WARNING—THISUNITMUST
NOT BE INSTALLED IN THE BEDROOM (per HUD
requirements).CAUTION—Thestructuralintegrity
ofthemobilehomeoor,wall,andceiling/roof
must be maintained.
• This appliance is not intended for commercial use.
• CAUTION:Burningfuelcreatescarbonmonoxide
and can be hazardous to your health if not
properly vented.
* This appliance is a freestanding heater. It is not intended to be attached to any type of ducting. It is not a
furnace.
Safety Precautions

3
HeatingSpecications
Fuel Burn Rate* (lowest setting) 1.5 lbs./hr.
Burn Time (lowest setting) 32hrs.(approximate)
Hopper Capacity 55 lbs.
Dimensions
Height 30.50 in. (774.6 mm)
Width 24.25 in. (615.9 mm)
Depth 26.19 in. (665.2 mm)
Weight 270 lbs.
ElectricalSpecications
Electrical Rating 115-120 volts, 60 HZ, 3.0 Amps
Watts (operational) 180W
Watts (igniter running) 346W
This manual describes the installation and operation of the United
States Stove Company Model 5660 pellet stove. This heater meets
the2015U.S.EnvironmentalProtectionAgency’scribwoodemission
limitsforwood-heaterssoldafterMay15,2015.UnderspecicEPA
test conditions burning Douglas Fir dimensional lumber this heater
has been shown to deliver heat at a rate of 11,370 to 34,260 Btu/hr.
This heater achieved a particulate emissions rate of 1.92 g/hr when
tested to method ASTM E 2779 / EPA Method 28R.
FUEL CONSIDERATIONS
Your pellet stove is designed and tested with premium grade pellets that comply with Pellet Fuels Institute
(PFI) standards. You can only burn premium grade pellets in this pellet heater. (Minimum of 40 lbs density per
cubic feet, 1/4” to 5/16” diameter, length no greater than 1.5”, not less than 8,200 BTU/lb, moisture under
8% by weight, ash under 1% by weight, and salt under 300 parts per million). Pellets that are soft, contain
excessiveamountsofloosesawdust,havebeen,orarewet,willresultinreducedperformanceandmay
cause damage to your heater. Store your pellets in a dry place.
DO NOT store the fuel within the installation clearances of the unit or within the space required for refueling
andashremoval.Doingsocouldresultinahousere.
Donotover-reorusevolatilefuelsorcombustibles,doingsomaycauseapersonalandpropertydamage
hazards.
SAFETY AND EPA COMPLIANCE
Your pellet stove has been approved for installation in the USA and Canada. It may also be installed in a
manufacturedormobilehome.YourstoveconformstoASTME1509,2012,andCertiedtoULCS627,2000,
and(UM) 84-HUD.
* Pellet size may effect the actual rate of fuel feed and burn times. Fuel feed rates may vary by as much as
20%. Use PFI listed fuel for best results.
Specications
Report No. 0215PS032E
WARNING: It is against federal regulations to operate this wood heater in a manner inconsistent with the
operatinginstructionsintheowner’smanual.
Note: Registeryourproductonlineatwww.usstove.com.See“LimitedWarranty”sectionforspecic
warranty information for your new purchase. Save your receipt with your records for any claims.

4
INSTALLATION OPTIONS
Read this entire manual before you install and use your pellet stove. Failure to follow instructions may result
inpropertydamage,bodilyinjury,orevendeath!(Seespecicinstallationdetailsforclearancesandother
installation requirements)
A Freestanding Unit—supported by pedestal/legs and placed on a non-combustible oor surface in
compliance with clearance requirements for a freestanding stove installation.
AnAlcoveUnit—supportedbypedestal/legsandplacedonanon-combustibleoorsurfaceincompliance
with clearance requirements for an alcove installation.
Your pellet stove may be installed to code in either a conventional or mobile home (see SPECIAL MOBILE
HOME REQUIREMENTS). The installation must comply with the Manufactured Home and Safety Standard
(HUD), CFR3280, Part 24.
It is recommended that only a authorized technician install your pellet stove, preferably an NFI certied
specialist.
DO NOT CONNECT THIS UNIT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.
The use of other components other than stated herein could cause bodily harm, heater damage, and void
your warranty.
IMPROPER INSTALLATION: The manufacturer will not be held responsible for damage caused by the
malfunction of a stove due to improper venting or installation. Call [phone] and/or consult a
professional installer if you have any questions.
Installation
CLEARANCES
Yourpelletstovehasbeentestedandlistedforinstallationinresidential,mobilehome,andalcoveapplications
in accordance with the clearances given. For safety reasons, please adhere to the installation clearances
and restrictions. Any reduction in clearance to combustibles may only be done by means approved by a
regulatory authority.
INSTALL ALL VENTS AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER
WhenyourPelletStoveRoomHeaterisbeinginstalledonacombustibleooritismandatorythata1/2”
(13mm) thick non-combustible hearth pad be installed under the heater. The non-combustible hearth pad
mustextendatleast6”beyondthefuelloadingandashremovalopeningsandatleastthedepthofthe
heaterplus6inches(152mm)outinfrontoftheheater.Theoorprotectormustextend2”(51mm)beyond
eachsideoftheexhaustvent.Thisappliestobothfreestandingheatersandinsertheaters.
BACK WALL
Figure 5
Figure 6 Alcove Dimensions
36”
35”
40”
2”
6”
USA 6”
CANADA 8”
FLOOR PROTECTION
USA 6”
CANADA 18”
2”
FLOOR
PROTECTION
USA 6”
CANADA 8”
USA 6”
CANADA 18”
BACK WALL
Figure 5
Figure 6 Alcove Dimensions
36”
35”
40”
2”
6”
USA 6”
CANADA 8”
FLOOR PROTECTION
USA 6”
CANADA 18”
2”
FLOOR
PROTECTION
USA 6”
CANADA 8”
USA 6”
CANADA 18”
BACK WALL
Figure 5
Figure 6
Alcove Dimensions
36”
35”
40”
2”
6”
USA 6”
CANADA 8”
FLOOR PROTECTION
USA 6”
CANADA 18”
2”
FLOOR
PROTECTION
USA 6”
CANADA 8”
USA 6”
CANADA 18”

5
FLOOR PROTECTION
Thisheatermusthaveanon-combustibleoorprotector(emberprotection)installedbeneathitiftheooris
ofcombustiblematerial.Ifaoorpadisused,itshouldbeULlistedorequal.Theoorpadornon-combustible
surface should be large enough to cover at least the area under the product and 6 in. (152 mm) beyond the
front and beyond each side of the fuel loading and ash removal openings. Your heater will need a minimum
31”x38”oorprotector.Floorprotectionmustextendunderand2in.(50.8mm)toeachsideofthechimney
teeforaninteriorverticalinstallation(seeFIGURE2).
Canadian Installations require a minimum of 450 mm [17.7”] beyond the front of the unit and 200mm [7.8”]
beyond each side of the unit. A Floor Protector of ¼ inch thick is recommended for this installation.

6
VENTING REQUIREMENTS
• Installventatclearancesspeciedbytheventmanufacturer.
• Do not connect the pellet vent to a vent serving any other appliance or stove.
• Donotinstallauedamperintheexhaustventingsystemofthisunit.
The following installation guidelines must be followed to ensure conformity with both the safety listing of this
stove and to local building codes. Do not use makeshift methods or compromise in the installation.
MAXIMUM VENTING DISTANCE
Installation MUST include at least 3-feet of vertical pipe outside the home. This will create some natural draft
to reduce the possibility of smoke or odor during appliance shutdown and keep exhaust from causing a
nuisanceorhazardbyexposingpeopleorshrubstohightemperatures.Themaximumrecommendvertical
ventingheight is 12-feetfor3-inch type “PL”vent.Total length ofhorizontalvent must notexceed4-feet.
This could cause back pressure. Use no more than 180 degrees of elbows (two 90-degree elbows, or two
45-degree and one 90-degree elbow, etc.) to maintain adequate draft.
IMPORTANCE OF PROPER DRAFT
Draft is the force which moves air from the appliance up through the chimney. The amount of draft in your
chimney depends on the length of the chimney, local geography, nearby obstructions and other factors. Too
muchdraftmaycauseexcessivetemperaturesintheappliance.Inadequatedraftmaycausebackpufng
intotheroomand‘plugging’ofthechimney.Inadequatedraftwillcausetheappliancetoleaksmokeinto
theroomthroughapplianceandchimneyconnectorjoints.Anuncontrollableburnorexcessivetemperature
indicatesexcessivedraft.Takeintoaccountthechimney’slocationtoinsureitisnottooclosetoneighborsor
in a valley which may cause unhealthy or nuisance conditions.
PELLET VENT TYPE
AULlisted3-inchor4-inchtype“PL”pelletventexhaustsystemmustbeusedforinstallationandattached
to the pipe connector provided on the back of the stove (use a 3-inch to 4-inch adapter for 4-inch pipe).
Connection at back of stove must be sealed using Hi-Temp RTV. Use 4-inch vent if the vent height is over 12-
feet or if the installation is over 2,500 feet above sea level.
We recommend the use of Simpson Dura-Vent® or Metal-Fab® pipe (if you use other pipe, consult your local
buildingcodesand/orbuildinginspectors).DonotuseType-BGasVentpipeorgalvanizedpipewiththisunit.
The pellet vent pipe is designed to disassemble for cleaning and should be checked several times during the
burning season. Pellet vent pipe is not furnished with the unit and must be purchased separately.
PELLET VENT INSTALLATION
Theinstallationmustincludeaclean-outteetoenablecollectionofyashandtopermitperiodiccleaning
oftheexhaustsystem.90-degreeelbowsaccumulateyashandsoottherebyreducingexhaustowand
performance of the stove. Each elbow or tee reduces draft potential by 30% to 50%.
All joints in the vent system must be fastened by at least 3 screws, and all joints must be sealed with Hi-Temp
RTVsiliconesealanttobeairtight.Theareawheretheventpipepenetratestotheexteriorofthehomemust
besealedwithsiliconeorothermeanstomaintainthevaporbarrierbetweentheexteriorandtheinterior
of the home. Vent surfaces can get hot enough to cause burns if touched by children. Non-combustible
shielding or guards may be required.
PELLET VENT TERMINATION
Do not terminate the vent in an enclosed or semi-enclosed area, such as; carport, garage, attic, crawl
space, under a sun deck or porch, narrow walkway, or any other location that can build up a concentration
of fumes. Termination in one of these areas can also lead to unpredictable pressure situations with the
appliance, and could result in improper performance and/or malfunction The termination must exhaust
above the outside air inlet elevation. The termination must not be located where it will become plugged by
snoworothermaterials.Donotterminatetheventingintoanexistingsteelormasonrychimney.
IMPORTANT! This unit is equipped with a negative draft system that pulls air through the burn pot and
pushestheexhaustoutofthedwelling.Ifthisunitisconnectedtoauesystemotherthantheway
explainedinthismanual,itwillnotfunctionproperly.

7
VENT TERMINATION CLEARANCES
A. Minimum 4-foot (1.22m) clearance below or beside any door or window that opens.
B. Minimum 1-foot (0.3m) clearance above any door or window that opens.
C. Minimum 3-foot (0.91m) clearance from any adjacent building.
D. Minimum 7-foot (2.13m) clearance from any grade when adjacent to public walkways.
E. Minimum 2-foot (0.61m) clearance above any grass, plants, or other combustible materials.
F. Minimum 3-foot (0.91m) clearance from an forced air intake of any appliance.
G. Minimum 2-foot (0.61m) clearance below eves or overhang.
H. Minimum 1-foot (0.3m) clearance horizontally from combustible wall.
I. Must be a minimum of 3 foot (0.091m) above the roof and 2 foot (0.61m) above the highest point or the
roof within 10 feet (3.05m).
G
VENTTERMINATIONCLEARANCES
Assembly Instructions
Step 1
Pull the factory installed wires
out of the top of the stove.
There will be two wire harnesses,
as shown.
Step 2
Unpack the top mount controls
and ensure that the wiring harness
shown is attached securely.
Step 3
Connect the factory installed
wiring harnesses to the control
panel as shown.
Step 4
Attach the control panel to the top of the stove, as
shown.
Step 5
Secure with two sheet metal screws.

8
You have already made the important decision of choosing your U.S. Stove Pellet Burning Room Heater; now
yournextstepistodeterminewheretoinstallyournewpelletstoveheater.Togetthemostefcientuseof
re-circulated heat, you should consider a room that is centrally located within your home. Choose a room
that is large and open.
ItisExtremelyImportanttomaintainproperclearancesfromanycombustiblesurfacesormaterialsinthe
roomwhereyourheaterwillbelocated.Youcanndproperclearancemeasurementsinthismanualand
on the rating label of your pellet stove.
The pellet stove can be vented through an exterior wall or into an existing masonry or metal chimney if
“PL”or“L”ventpipeisusedthroughoutexistingchimney.Ventingcanpassthroughtheceilingandroofif
approved pipe is used. Where passage through a wall, or partition of combustible construction is desired, the
installation must conform to CAN/CSA-B365.
DONOTOBTAINCOMBUSTIONAIRFROMTHEATTIC,GARAGEORANYOTHERUNVENTILATEDAREA.YOUMAY
OBTAIN COMBUSTION AIR FROM A VENTILATED CRAWL SPACE.
DONOTINSTALLAFLUEDAMPERINTHEEXHAUSTVENTINGSYSTEMOFTHISUNIT.
DONOTCONNECTTHISUNITTOACHIMNEYFLUESERVINGANOTHERHEATER,FURNACEORAPPLIANCE.
INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER.
ONLYUSEAPPROVEDMATERIALFORINSTALLATION,FAILURETODOSOMAYRESULTINPROPERTYDAMAGE,
BODILY INJURY, OR EVEN DEATH.
Thisapplianceiscertiedforusewithlisted3inchor4inch“PL”or“L”pelletventingproducts.Theuseofother
components other than stated herein could cause bodily harm, heater damage, and void your warranty.
HORIZONTAL EXHAUST VENT INSTALLATION
1. Locate your pellet stove in a location which meets the requirements of this manual, but in an area where
it does not interfere with the house framing, wiring, etc.
2. Installanon-combustiblehearthpadunderneaththepelletstove.Thispadshouldextendatleast6”
(152mm) in front of the unit.
3. Placethepelletstoveapproximately15”(381mm)awayfromtheinteriorwall.
4. Locatethecenteroftheexhaustpipeofyourunit.Thispointshouldthenbeextendedtotheinteriorwall
of your house. Once you have located the center point, on the interior wall, cut a 7” (175mm) diameter
hole through the wall.
5. Thenextstepistoinstallthewallthimble,refertotheinstructionswhichcomewiththewallthimblefor
this step.
6. Install the appropriate length of exhaust vent pipe into the wall thimble. See steps 11 and 12 when
determiningthecorrectlengthofexhaustventtouse.
7. Outside Fresh Air is Mandatory when installing this pellet stove room heater in airtight homes and mobile
homes. Be sure that the outside air vent has an approved cap on it to prevent rodents from entering. Be
suretoinstallinlocationthatwon’tbecomeblockedwithsnow,etc.
8. Theairintakepipeisequippedwithabutteryvalvethatispresettomaximumairintake.Foroptimum
operatingefciencyyoumaycalibratethebutteryvalvetoprovidelessintakeair.Caution: Too much
restriction on the intake air will cause dirtier burn, therefore, will require more frequent cleaning.
9. Connecttheexhaustventpipetotheexhaustoutletofyourpelletstove.
10. Secure all vent joint connections with 3 screws. Seal the exhaust vent joint connections with high
temperature silicone sealant.
11. Push the unit straight back to the interior wall, being sure to maintain the minimum clearances to
combustibles 6” (152mm) to the back of the unit. Seal the annular space of the wall thimble and around
the vent pipe with high temperature silicone sealant.
12. The exhaust vent pipe must extend at least 12” (300mm) out past the exterior wall. Seal the annular
space of the wall thimble and around the vent pipe with high temperature silicone sealant.
13. Install an approved horizontal termination cap or if necessary install a 90° elbow and appropriate length
of vertical venting. An approved vertical vent cap is recommended.
Installation

9
TYPICAL THROUGH THE WALL INSTALLATION
THROUGH THE WALL INSTALLATION (RECOMMENDED INSTALLATION)
Canadian installations must conform to CAN/CSA-B365. To vent the unit through the wall, connect the pipe
adaptertotheexhaustmotoradapter.Iftheexhaustadapterisatleast18in.(457mm)abovegroundlevel,
a straight section of pellet vent pipe can be used through the wall.
Your heater dealer should be able to provide you with a kit that will handle most of this installation, which
will include a wall thimble that will allow the proper clearance through a combustible wall. Once outside the
structure, a 3 in.(76mm) clearance should be maintained from the outside wall and a clean out tee should be
placed on the pipe with a 90-degree turn away from the house. At this point, a 3ft (0.91m) (minimum) section
of pipe should be added with a horizontal cap, which would complete the installation.
A support bracket should be placed just below the termination cap or one every 4ft (1.22m) to make the
system more stable. If you live in an area that has heavy snowfall, it is recommended that the installation be
taller than 3ft (0.91m) to get above the snowdrift line. This same installation can be used if your heater is below
ground level by simply adding the clean-out section and vertical pipe inside until ground level is reached.
With this installation you have to be aware of the snowdrift line, dead grass, and leaves. We recommend a
3ft (0.91m) minimum vertical rise on the inside or outside of the house.
The“throughthewall”installationistheleastexpensiveandsimplestinstallation.Neverterminatetheend
vent under a deck, in an alcove, under a window, or between two windows.
THROUGH THE ROOF/CEILING
INSTALLATION
When venting the heater through the
ceiling, the pipe is connected the same as
through the wall, except the clean-out tee
is always on the inside of the house, and a
3 in.(76mm) adapter is added before the
clean-out tee.
You must use the proper ceiling support
anges and roof ashing (supplied by
the pipe manufacturer; follow the pipe
manufacturer’s directions).  It is important
to note that if your vertical run of pipe is
more than 15ft (4.57m), the pellet vent pipe
size should be increased to 4 in. (102mm) in
diameter.
Do not exceed more than 4ft (1.22m) of
pipe on a horizontal run and use as few
elbows as possible. If an offset is required,
it is better to install 45-degree elbows rather
than 90-degree elbows.
Installation

10
OUTSIDE AIR SUPPLY (OPTIONAL,UNLESSINSTALLINGINAMOBILEHOME)
Depending on your location and home construction, outside air may be necessary for optimal performance.
Metalpipe(solidorexible)mustbeusedfortheoutsideairinstallation.PVCpipeisNOTapprovedand
should NEVER be used.
A wind shield over the termination of the outside air pipe or a 90-degree elbow or bend away from the
prevailing winds MUST be used when an outside air pipe is installed through the side of a building. The outside
airterminationMUSTbeatleast1ft(0.305m)awayfromtheexhaustsystemtermination.
The outside air pipe on your heater is 2” (50.8mm) OD. The outside air connecting pipe must be at least 2”
(50.8mm) ID. The outside air connection used MUST NOT restrict the amount of air available to your heater.
Theoutsideairconnectingpipemustbeasshortandfreeofbendsaspossible,anditmusttover,notinside,
the outside air connection to the heater.
NOTE: Dimensionsfromtheoortoyourstovesinlet/exhaustpipesare
approximateandmayvarydependingonyourinstallation.
16.83
10.02 FRESH AIR INTAKE
EXHAUST PIPE
17.06
11.47
TYPICAL FRESH AIR TERMINATION
EXHAUST/INLET LOCATIONS
Installation

11
Mobile home installation should be done in accordance with the Manufactured Home and Safety Standard
(HUD), CFR 3280, Part 24. Canadian installations require that the heater must be connected to a 3 or 4 inch,
factory-built chimney conforming to CAN/ULC-S629. See the installation illustrations in this manual for minimum
height above the roof. The chimney installation must allow for removal in case of mobile home transportation,
especially outside connections. You may contact your local building authority or person having jurisdiction
on height restrictions.
In order for this unit to be installed in a mobile home the following criteria must be met:
• Theunitmustbesecuredtotheoorusinglagboltsintheholesprovidedinthepedestalbase.
• Ensure that the unit is permanently electrically grounded to the chassis of your home with 18 gauge
copper wire.
• Allexhaustsystemsmusthaveasparkarrestor.
ITISMANDATORYTOTAKETHECOMBUSTIONAIRFROMTHEOUTSIDEWHENINSTALLINGTHISUNITINAIRTIGHT
OR MANUFACTURED/MOBILE HOMES.
CAUTION:Thestructuralintegrityofthemanufacturedhomeoor,wall,andceiling/roofmustbemaintained.
Make sure to maintain an effective vapor barrier by sealing with silicone where the chimney or other
components penetrate to the exterior of the structure. Refer to and follow the chimney manufacturer’s
installation instructions.
WARNING: Do not install in sleeping room.
NOTE: Only the free standing model is approved for installation into a mobile home.
Figure 15
HEARTH PAD
FLOORING
GROUND WIRE, DIRECTLY
TO METAL CHASSIS
STEEL FRAME
1/4” LAG BOLTS,
SECURELY FASTENED
Mobile Home Installation

12
PANEL/REMOTE CONTROLS
The blowers and automatic fuel supply are controlled from a panel on the top of the
stove. The control panel functions are a follows.
A. ON/OFF SWITCH (“POWER” BUTTON)
• Whenpushed,thestovewillautomaticallyignite.Nootherrestarterisnecessary.
The igniter will stay on for at least 10 and up to 12 minutes, depending on when Proof
ofFireisreached.Thereshouldstartinapproximately5minutes.
• The red light located above the “POWER” button will turn green when pressed and
remain green until the stove is turned off.
• After pushing “POWER”, the auger motor is on for 3.5 minutes, off for 1 minute. During
the remainder of the start-up period, the auger motor operates on the heat range
“1” setting.
• During start up the heat level advance (Up and Down keys) will change the heat
range indicator level accordingly, but there is no change in the stoves operating
conditions until start-up is completed.
• During start-up ignition must occur within 12 minutes or the stove will error out and
show E4.
• During the start-up phase, the Mode key does not function.
B. LEVEL / TEMP ARROW BUTTONS
• These buttons when pushed will set the pellet feed rate, hence the heat output or
heat range of your stove.
• The levels of heat output will incrementally change on the bar graph starting from
heat range “1” to heat range “5”.
C. °C / °F BUTTON
• The °C / °F button changes the two digit
display from degrees Celsius to degrees
Fahrenheit.
D. MODE (M/T) BUTTON
• The Mode of the stove can be switched
between manual and controlled with a
Thermostat. Separate LEDs to the left of
the two digit display indicate the mode of
operation – Manual or T-Stat. The stove has
to be in normal operation to be switched
from Manual to T-Stat mode.
• Manual mode operates according to the
5 set levels of feed on the bar graph from
heat range “1” to heat range “5”.
• T-Stat mode works as follows:
• The stove has a built in Thermostat into the controls of the appliance. The temperature sensor for the
T-Stat is located on the back of the stove behind the display board.
• Once the stove has gone into run mode the stove can be switch into T-Stat mode.
• The Up and Down Level / Temp Arrow buttons are used to change the desired set-point temperature.
Oncethedesiredtemperatureisreachedthetwodigitdisplaywillashforfoursecondsandresettothe
actual room temperature.
• Once the stove reaches within 3°F of the desired temperature set point, it returns to the heat range that
the stove was set on before it was switched to T-Stat mode (if the stove was running on heat range “5”
when switched to T-stat mode when it gets within 3°F of the set point it will return to heat range “5”).
• Once the stove reaches the desired set-point, the stove will drop to heat range “1”.
• When room temperature drops below desired set-point the stove will ramp back up until it reaches the
desired temperature.
Level/Temp
Manual
T-Stat
Appliance Controls

13
• DO NOT USE CHEMICALS OR FLUIDS TO START THE FIRE - Never use gasoline, gasoline-type lantern fuel,
kerosene,charcoallighteruid,orsimilarliquidstostartor“freshenup”areinthisstove.Keepallsuch
liquids well away from the stove while it is in use.
• HOTWHILEINOPERATION.KEEPCHILDREN,CLOTHINGANDFURNITUREAWAY.CONTACTMAYCAUSESKIN
BURNS.
This heater is designed to burn only PFI Premium grade pellets. This appliance can also burn pellets rated as
standard after May 16, 2015
DO NOT BURN:
Burning these materials may result in release of toxic fumes or render the heater ineffective and cause
smoke.
PROPER FUEL
THISSTOVEISAPPROVEDFORBURNINGPELLETIZEDWOODFUELONLY!Factory-approvedpelletsarethose
1/4”or5/16”indiameterandnotover1”long.Longerorthickerpelletssometimesbridgetheaugerights,
which prevents proper pellet feed. Burning wood in forms other than pellets is not permitted. It will violate the
building codes for which the stove has been approved and will void all warranties. The design incorporates
automaticfeedofthepelletfuelintothereatacarefullyprescribedrate.Anyadditionalfuelintroduced
by hand will not increase heat output but may seriously impair the stoves performance by generating
considerablesmoke.Donotburnwetpellets.Thestove’sperformancedependsheavilyonthequalityof
your pellet fuel. Avoid pellet brands that display these characteristics:
1. ExcessFines–“Fines”isatermdescribingcrushedpelletsorloosematerialthatlookslikesawdustorsand.
Pelletscanbescreenedbeforebeingplacedinhoppertoremovemostnes.
2. Binders – Some pellets are produced with materials to hold the together, or “bind” them.
3. High ash content – Poor quality pellets will often create smoke and dirty glass. They will create a need for
more frequent maintenance. You will have to empty the burn pot plus vacuum the entire system more
often. Poor quality pellets could damage the auger. We cannot accept responsibility for damage due
to poor quality pellet.
PRE-START-UP CHECK
Removeburnpot,makingsureitiscleanandnoneoftheairholesareplugged.Cleantherebox,andthen
reinstallburnpot.Cleandoorglassifnecessary(adryclothorpapertowelisusuallysufcient).Neveruse
abrasivecleanersontheglassordoor.Checkfuelinthehopper,andrellifnecessary.
BUILDING A FIRE
Never use a grate or other means of supporting the fuel. Use only the burn pot supplied with this heater.
Hopper lid must be closed in order for the unit to feed pellets.
During the start-up period:
1. Make sure burn pot is free of pellets.
2. DO NOT open the viewing door.
3. DO NOT open the damper, the damper needs to be closed during start up.
4. DO NOT add pellets to the burn pot by hand.
NOTE:Duringtherstfewres,yourstovewillemitanodorasthehightemperaturepaintcuresorbecomes
seasonedtothemetal.Maintainingsmallerreswillminimizethis.Avoidplacingitemsonstovetopduringthis
period because paint could be affected.
1. Garbage;
2. Lawn clippings or yard waste;
3. Materials containing rubber, including tires;
4. Materials containing plastic;
5. Waste petroleum products, paints or paint
thinners, or asphalt products;
6. Materials containing asbestos;
7. Construction or demolition debris;
8. Railroad ties or pressure-treated wood;
9. Manure or animal remains;
10. Salt water driftwood or other previously salt
water saturated materials;
11. Unseasoned wood; or
12. Paper products, cardboard, plywood, or
particleboard. The prohibition against burning
thesematerialsdoesnotprohibittheuseofre
starters made from paper, cardboard, saw dust,
wax and similar substances for the purpose of
startingareinanaffectedwoodheater.
Operation

14
THE HOTROD FIRESTARTER
1. Fill hopper and clean burn pot.
2. Press “On/Off” button. Make sure green light comes on.
3. The damper should be completely closed or open no more than ¼ of the way during start-up. This
willvarydependingonyourinstallationandelevation.Oncereisestablishedadjustfordesiredame
increasing the amount the damper is open as the heat setting is increased. (See “DAMPER CONTROL”)
4. Adjust feed rate to desired setting by pressing “Heat Level Advance” button.
Ifredoesn’tstartin12minutes,press“On/Off”,waitafewminutes,cleartheburnpot,andstartprocedure
again.
DAMPER CONTROL
The damper control lever is located on the back of the stove on the lower left side. The dampener adjusts
the combustion air. This control is necessary due to the varied burn characteristics of individual installations,
differentpelletbrandsandpelletfeedrates.Itallowsyoutoimprovetheefciencyofyourstove.Providing
correct combustion air will reduce the frequency of cleaning your glass door and prevent the rapid buildup
of creosote inside your stove and chimney.
Youshouldadjustthedamperbasedonthere’sappearance.Alow,reddish,dirtyrecanbeimproved
byturningthedampenerslightlytotheright.A“blowtorch”recanbeimprovedbyturningthedampener
to the left a little bit.
As a general rule, on lower feed rate settings, the damper should be farther to the left closing it off. On higher
feed rates, the damper should be open more by having it set more towards the right. Through trial and error,
youwillndthebestsetting.Consultyourdealerifyouneedhelp.
NOTE: On heat range “1”, damper should be either completely closed or open no more than a ¼ of the way.
Ifdamperisopentofar,itcancausetheretogoout.
OPENING DOOR
If the door is opened while the stove is in operation it must be closed within 30 seconds or the stove will shut
down. If the stove shuts down push the “On/Off” button to re-start your stove. The stove will have to fully shut
down and turn off before you will be able to restart the stove.
ROOM AIR FAN
WhenstartingyourstovetheRoomAirFanwillnotcomeonuntilthestove’sheatexchangerwarmsup.This
usually takes about 10 minutes from start-up.
IF STOVE RUNS OUT OF PELLETS
Theregoesoutandtheaugermotorandblowerswillrununtilthestovecools.Thiswilltake30minutesor
longer depending on the heat remaining in the appliance. After the stove components stop running all lights
onthedisplaywillgooutandthetwodigitdisplaywillbeginashing“E3”
REFUELING
• The hopper and stove top will be hot during operation; therefore, you should always use some type of
hand protection when refueling your stove.
• Never place your hand near the auger while the stove is in operation.
We recommend that you not let the hopper drop below ¼ full.
KEEP HOPPER LID CLOSED AT ALL TIMES EXCEPT WHEN REFILLING.
DO NOT OVERFILL HOPPER.
SHUTDOWN PROCEDURE
Turning your stove off is a matter of pressing the “POWER” button on the display board. The green light will
turn back to red when the “POWER” button is pushed. The auger motor will stop, and the blowers will continue
tooperateuntiltheinternalreboxtemperatureshavefallentoapresetlevel.
WARNING: Never shut down this unit by unplugging it from the power source.
Operation

15
1. Your stove is equipped with a high temperature thermodisc. This unit has a manual reset thermodisc. This
safety switch has two functions.
A. To recognize an overheat situation in the stove and shut down the fuel feed or auger system.
B. Incaseofamalfunctioningconvectionblower,thehigh-temperaturethermodiscwillautomatically
shut down the auger, preventing the stove from overheating.
NOTE: On some units, once tripped, like a circuit breaker, the reset button will have to be pushed before
restarting your stove. On other units the thermodisc has no reset button and will reset itself once the stove has
cooled. The manufacturer recommends that you call your dealer if this occurs as this may indicate a more
serious problem. A service call may be required.
2. If the combustion blower fails, an air pressure switch will automatically shut down the auger.
NOTE: Opening the stove door for more than 30 seconds during operation will cause enough pressure
change to activate the air switch, shutting the fuel feed off. The stove will shut down and show “E2” on the
two digit display. The stove has to fully shut down before restarting.
TAMPER WARNING
This wood heater has a manufacturer-set minimum low burn rate that must not be altered. It is against
federal regulations to alter this setting or otherwise operate this wood heater in a manner inconsistent with
operating instructions in this manual.
VISIBLE SMOKE
Theamountofvisiblesmokebeingproducedcanbeaneffectivemethodofdetermininghowefciently
the combustion process is taking place at the given settings. Visible smoke consist of unburned fuel and
moisture leaving your stove. Learn to adjust the air settings of your specic unit to produce the smallest
amount of visible smoke. Wood that has not been seasoned properly and has a high wood moisture content
willproduceexcessvisiblesmokeandburnpoorly.
• Failure to clean and maintain this unit as indicated can result in poor performance and safety hazards.
• Unplugyourstove’selectricalcordpriortoremovingthebackpaneloropeningtheexhaustsystemfor
any inspection, cleaning, or maintenance work.
• Never perform any inspections, cleaning, or maintenance on a hot stove.
• Donotoperatestovewithbrokenglass,leakageofuegasmayresult.
• Attemptstoachieveheatoutputratesthatexceedheaterdesignspecicationscanresultinpermanent
damage to the heater.
EXHAUST SYSTEM
Creosote Formation – When any wood is burned slowly, it produces tar and other organic vapors, which
combine with expelled moisture to form creosote. The creosote vapors condense in the relatively cool
chimneyueoranewlystartedreorfromaslow-burningre.Asaresult,creosoteresidueaccumulateson
theuelining.Whenignited,thiscreosotemakesanextremelyhotre,whichmaydamagethechimneyor
evendestroythehouse.Despitetheirhighefciency,pelletstovescanaccumulatecreosoteundercertain
conditions.
FlyAsh–Thisaccumulatesinthehorizontalportionofanexhaustrun.Thoughnon-combustible,itmayimpede
thenormalexhaustow.Itshouldthereforebeperiodicallyremoved.
InspectionandRemoval–Thechimneyconnectorandchimneyshouldbeinspectedbyaqualiedperson
annually or per ton of pellets to determine if a creosote or y ash build-up has occurred. If creosote has
accumulated,it shouldberemoved toreducethe riskofa chimneyre.Inspect thesystemat thestove
connection and at the chimney top. Cooler surfaces tend to build creosote deposits quicker, so it is important
to check the chimney from the top as well as from the bottom. The creosote should be removed with a brush
specicallydesignedforthetypeofchimneyinuse.Aqualiedchimneysweepcanperformthisservice.Itis
also recommended that before each heating season the entire system be professionally inspected, cleaned
and, if necessary, repaired. To clean the chimney, disconnect the vent from the stove.
Maintenance

16
INTERIOR CHAMBERS
• Burn Pot: Periodically remove and clean the burn pot and the area inside the burn pot housing. In
particular, it is advisable to clean out the holes in the burn pot to remove any build up that may prevent
air from moving through the burn pot freely.
• HeatExchanger:Thereisacleanoutplateonbothsidesoftheheatexchangerthatneedtoberemoved
tocleanyashoutoftheheatexchanger.Thecleanoutsarelocatedinsidethecabinetdoors,onthe
lowerfrontcornersoftheheatexchanger.Itisimperativethattheybecleanedoutataminimumofonce
per month. To access these clean outs, you must remove both side panels. The clean outs are secured
tothereboxwith(2)5/16”screws.
Remove the clean outs and
vacuum out any accumulated
ash. This should be done at least
once per month or more frequently
if large amounts of ash are noticed
while cleaning or if the stove does
not seem to be burning properly
If a vacuum is used to clean your stove,
we suggest using a vacuum designed
for ash removal. Some regular vacuum
cleaner (i.e. shop vacs) may leak ash
into the room.
DO NOT VACUUM HOT ASH
CLEANING
Heat Exchanger Tubes – Your Pellet
Stove Room Heater is designed with a
built in heat exchanger tube cleaner.
This should be used every 2 or 3 days
to remove ash build up on the heat
exchanger tubes, which can reduce
heat transfer. The handle, for the heat
exchanger tube cleaner, is located in
front of the vent tubes on front side of heater. Slide the rod front to back several times to clean the tubes then
follow the instructions for ash removal.
Periodically remove the clean outs on either side
oftheheatexchanger.Cleanouttheash,then
follow the instructions for ash removal. Check the
gasket before replacing the clean out cover. If
gasket is damaged new gasket can be ordered.
Alternatively, high temperature silicone can be
used to ensure a proper seal between the clean
out cover and the stove body.
FANS – DANGER: RISK OF ELECTRIC SHOCK.
DISCONNECT POWER BEFORE SERVICING
UNIT
Over time ash or dust may accumulate on the
bladesofthecirculation&exhaustfans.Thefans
should be inspected, periodically, and if any
accumulation is present vacuumed clean as the
ash or dust can impede the fans performance.
Heat Exchanger
Cleaner Handle
Cleanouts
Cover
Gasket
Figure 27
Circulation Fan Exhaust Fan
Igniter
Auger Motor
WARNING:Donotattempttooperatetheheatexchangetubecleanerwhilethepelletstoveisin
operation or cooling down; wait until pellet stove has cooled completely before performing this
procedure.
WARNING: Failure to properly maintenance the clean outs will result in
poor performance of this stove.
Maintenance

17
Itisalsopossiblethatcreosotemayaccumulateintheexhaustfantherefore,thismustbebrushedclean.
Theexhaustfancanbefoundbehindtheleftsidepanel (facing the frontoftheheater),thecirculation
fan can be found behind the right side panel. To access the igniter, remove the air inlet tube and cover (2
screws). The auger motor is located in the center rear of the unit.
Note: When cleaning, take care not to damage the fan blades.
CHECK AND CLEAN THE HOPPER
Checkthe hopper periodically todetermineifthere is anysawdust(nes)that is buildingupinthefeed
system or pellets that are sticking to the hopper surface. Clean as needed.
DOOR AND GLASS GASKETS
Inspect the main door and glass window gaskets periodically. The main door may need to be removed to
havefrayed,broken,orcompactedgasketsreplacedbyyourauthorizeddealer.Thisunit’sdoorusesa3/4”
diameter rope gasket.
BLOWER MOTORS
Cleantheairholesonthemotorsofboththeexhaustanddistributionblowersannually.Removetheexhaust
blowerfromtheexhaustductandcleanouttheinternalfanbladesaspartofyourfallstart-up.
PAINTED SURFACES
Painted surfaces may be wiped down with a damp cloth. If scratches appear, or you wish to renew your
paint, contact your authorized dealer to obtain a can of suitable high-temperature paint.
GLASS - CLEANING, REMOVAL AND REPLACEMENT OF BROKEN DOOR GLASS
Cleaning - We recommend using a high quality glass cleaner. Should a buildup of creosote or carbon
accumulate, you may wish to use 000 steel wool and water to clean the glass. DO NOT use abrasive cleaners.
DO NOT perform the cleaning while the glass is HOT. ,
Intheeventyouneedtoreplacetheglass,Donotattempttooperatetheunitwithbrokenglass.Replacement
glass may be purchased from your U.S. Stove Pellet Burning Room Heater Dealer. If glass is broken, follow
these removal procedures:
Replacement glass must be 0.197” thick tempered ceramic glass with a working service temperature of 1400
deg. F.
CenterGlasssize:10”x10.67”Sideglasssize:4”x10.67”
1. Once the heater has cooled, remove the door from the heater.
2. Remove the rope gasket from the door followed by the eight(8) nuts holding the glass retainer in place.
3. While wearing gloves, carefully remove any loose pieces of glass from the door frame.
4. Replace the glass and gasket, making sure the gasket runs the full perimeter of the glass edge.
5. Re-install the retainer and eight nuts and rope gasket using high temperature silicone to adhere the
gasket to the door.
6. Never use substitute materials for the glass.
DO NOT abuse the door glass by striking, slamming or similar trauma. Do not operate the stove with the glass
removed, cracked or broken.
FALL START UP
Priortostartingtherstreoftheheatingseason,checktheoutsideareaaroundtheexhaustandairintake
systemsforobstructions.Cleanandremoveanyyashfromtheexhaustventingsystem.Cleananyscreens
ontheexhaustsystemandontheoutsideairintakepipe.Turnallofthecontrolsonandmakesurethatthey
are working properly. This is also a good time to give the entire stove a good cleaning throughout.
SPRING SHUTDOWN
After the last burn in the spring, remove any remaining pellets from the hopper and the auger feed system.
Scoopoutthepelletsandthenruntheaugeruntilthehopperisemptyandpelletsstopowing(thiscanbe
done by pressing the “ON” button with the viewing door open). Vacuum out the hopper. Thoroughly clean
theburn pot, andrebox.It may bedesirableto spray theinside of thecleanedhopper with anaerosol
siliconesprayifyourstoveisinahighhumidityarea.Theexhaustsystemshouldbethoroughlycleaned.
Maintenance

18
Daily Weekly Monthly or as needed
Burn Pot Stirred Empty
Combustion Chamber Brushed
Ashes Check Empty
Interior Chambers Vacuumed
Combustion Blower Blades Vacuumed / Brushed
Convection Blower Impeller Vacuumed / Brushed
Vent System Cleaned
Gaskets Inspected
Glass Wiped/Cleaned
Hopper (end of season) Emptied and vacuumed
Heat Exchanger Tubes Bi-Weekly
Attention: This wood heater needs periodic inspection and repair for proper operation. It is against
federal regulations to operate this wood heater in a manner inconsistent with operating instructions in this
manual.
MAINTENANCE SCHEDULE
Use the following as a guide under average use conditions.
Gasketsarounddooranddoorglassshouldbeinspectedandrepairedorreplacedwhennecessary.
ASH REMOVAL - FREESTANDING UNIT
Remove the ashes periodically to avoid unnecessary ash build up. Ash removal is as follows:
1. Letreburnoutandallowunitcooltoroomtemperature.
2. Cleantheheatexchangertubes(seeHeatExchangerCleaningsection)–MakesurePelletStoveisat
room temperature before touching .
3. Open the ash pan door, remove the burn pot and empty into metal container.
4. Vacuumtoremoveashesfromtherebox.
5. BESURETHATASHESARECOOLTOTHETOUCHBEFOREVACUUMING.Somevacuumcleanersmayleak
ashintotheroom.Yourvacuumcleanershouldhaveaspeciallterorbagtoeliminateleakage.
6. Remove ash pan and dispose of ashes into metal container.
7. Reinstall ash pan.
8. Reinstall burn pot.
Maintenance

19
ASH REMOVAL - INSERT UNIT
1. Allow Heater to cool to room temperature
2. Lift the ash pan door up and pull out
3. Follow directions for free-standing unit above on
this page.
DISPOSAL OF ASHES
Ashes should be placed in a steel metal container
with a tight tting lid.  The closed container of ashes
should be placed on a non-combustible oor or on
the ground well away from all combustible materials,
pendingnaldisposal.Iftheashesaredisposedofby
burial in soil or otherwise locally dispersed, they should
be retained in the closed container until all cinders
have been thoroughly cooled. Do not place other
waste in the same container.
SMOKE AND CO MONITORS
Burningwoodnaturallyproducessmokeandcarbonmonoxide(CO)emissions.COisapoisonousgaswhen
exposedtoelevatedconcentrationsforextendedperiodsoftime.Whilethemoderncombustionsystemsin
heatersdrasticallyreducetheamountofCOemittedoutthechimney,exposuretothegasesinclosedor
connedareascanbedangerous.Makesureyourstovegasketsandchimneyjointsareingoodworking
orderandsealingproperlytoensureunintendedexposure.Itisrecommendedthatyouusebothsmokeand
CO monitors in areas having the potential to generate CO.
Ash Pan Door
STEP 1
Locate the Burn Pot.
Above are the decorative logs in there correct location.
Your decorative logs should come in place, however if this is not the case the following steps depicts the
correct location. STEP 2
Place log into correct position.
Burn Pot
Maintenance
Maintenance

20
Whenyourstoveactsoutoftheordinary,therstreactionistocallforhelp.Thisguidemaysavetimeand
money by enabling you to solve simple problems yourself. Problems encountered are often the result of
onlyvefactors:1)poorfuel;2)pooroperationormaintenance;3)poorinstallation;4)componentfailure;
5) factory defect. You can usually solve those problems related to 1 and 2. Your dealer can solve problems
relating to 3, 4 and 5.
For the sake of troubleshooting and using this guide to assist, you should look at your heat level setting to see
whichlightisashing.
• Disconnect the power cord before performing any maintenance! NOTE: Turning the ON/OFF Switch to
”OFF” does not disconnect all power to the electrical components of the stove.
• Never try to repair or replace any part of the stove unless instructions for doing so are given in this
manual. All other work should be done by a trained technician.
Display is Flashing “E1”
Possible Causes PossibleRemedies:(Unplugstoverstwhenpossible)
1. The convection blower is overheating and tripping
the internal temperature shutoff. Clean any dust off of the windings and fan blade. If oiling the blower does not help, the blower may be bad.
2. The stove is being left on the highest setting for
extendedperiodsoftime.
If operating the heater on the highest heat setting, the
room temperature could increase enough and lead
to potential overheating situations. If this happens try
operating at a lower heat setting.
3. Fuel other than wood pellets is being burned in the
stove.
This pellet stove is designed and tested to use wood
pellets. Check for signs of fuel other than wood pellets.
No other types of fuel have been approved for this pellet
stove. If there are signs of other types of fuel being used,
stop using them immediately.
4. Power surge or brown out situation.
A power surge, spike, or voltage drop could cause the
high limit switch to trip. Check to see if a surge protector
is being used on the stove. If not, recommend one to the
customer.
5. High Limit Switch is malfunctioning. If the other items check out OK, replace the high limit
switch.
Trouble Shooting Guide