usi CF-B-AG-01 User manual

Configure the Wireless Network
To configure the wireless network in a PocketPC environment:
1.Tap Start Settings System
tab.
2.Tap theUSI WLAN CF Card icon to
run the Wireless Networking Setting
utility.
3.Select, add, or delete a profile:
a. Select a profile from the drop-down
menu, and tap OKto switch your station
from one wireless network to another.
b. Tap Add orEdit to add or edit the
selected profile.
c. TapDelete to delete the selected
profile.
4. Tap Next, and set the
Network Name.
USI WLAN CF Card802.11b 2.4GHz
Quick Start Guide
5. Tap Next, and configre
your security settings.
6. Tap Next, and turn Power Management on or off.
7. Click finish.
Finding Information
• For more information, see the User's Guide on the CD that came with the card.
• For the latest information, go to the USI website at www.usi.com.tw
Information in this document is subject
to change without notice.
2002 Universal Scientific Industrial
Co.,Ltd.All rights reserved.
Install the Driver
To install the driver and utility on your Pocket PC from the software and
documentation CD:
1. Using your sync cable or cradle, connect your Pocket PC to
the computer. For additional information, see the documen-
tation that came with your Pocket PC.
2. Insert the software and documentation CD into the drive on
the computer.
3. Using Microsoft Windows Explorer or My Computer, navigate
to x:\Setup, where xis the CD drive letter.
4. Double-click setup.exe.
5. Follow the instructions on the computer screen to finish the
installation.
6. Insert the USI WLAN CF Card into the CF Cardslot on your
PocketPC.
Reproduction in any manner whatso-
ever without the written permission of
USI is strictly forbidden.

Federal Communications Commission (FCC) Requirements, Part 15
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
---Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation
IMPORTANT NOTE
FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction
with any other antenna or transmitter.
Regulatory information / Disclaimers
Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the
user documentation provided with the product. Any changes or modifications (including the antennas) made to
this device that are not expressly approved by the manufacturer may void the user’s authority to operate the
equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized
modification of this device, or the substitution of the connecting cables and equipment other than manufacturer
specified. It is the responsibility of the user to correct any interference caused by such unauthorized modification,
substitution or attachment. Manufacturer and its authorized resellers or distributors will assume no liability for any
damage or violation of government regulations arising from failing to comply with these guidelines.
Use on the supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter
and may violate FCC regulations.