UWICOM GENIESORI II User manual

LED Indicator
Earphone Jack
Function Button
Up Button
Down Button Dual MIC
Power Switch
Features Defined
Default usage method
Power On and Off.
At power-on, the LED on the
selected tone flashes 1 time
and the green LED flashes 2 times
Basic operation of buttons.
Divide into short and long presses depending on the time
you press.
- Short : When the button is pressed and hold within 2 sec.
(the white LED is on)
- Long : When the button is pressed and hold for more than
2 sec. (the blue LED is on)
At first, press the "Down Button" for long to enter DB selection
mode. And then, press the "Function Button" for short.
Every time you press it, you can hear and select 7 different tones.
After you select mode, press the "Down Button" long again to
save tone.
* If you want to change the mode later, follow this guide.
Press the function button long to
change to the Bluetooth mode.
Notifies the battery condition when
power is turned on. Charge with a
Micro USB Cable. During charging,
the red LED lights up and it goes off
when charging is completed.
Microphone Mode
Amplifies the microphone sound according to the
selected DB.
You can adjust the sound volume in 16 steps (LED shown) with
a short press of the "+" up button and the "-" down button.
- Low volume (1) : Red LED
- Medium volume (2-15) : Green LED
- High volume (16) : Blue LED
Volume control.
Battery status and charging.
SHORT PRESS
1~2 SEC.
LONG PRESS
OVER 2 SEC.
LONG PRESS
OVER 2 SEC.
Select the hearing-mode.
Change to Bluetooth mode.
Connect a phone call.
It must be registered to the
smartphone through pairing.
When a call is incoming, press the function
button long to connect the voice call automatically.
DB1 RED DB2 ORANGE DB3 YELLOW DB4 GREEN
DB5 BLUEDB6 INDOGODB7 PURPLE
Nomal High Amp 1 Low Amp 1
Low-High Amp High Amp 3 High Amp 2
Low Amp 2
LONG PRESS
OVER 2 SEC.
Press the Function button for short when you want
to enter the Noise Cancellation (NC) mode.

Personal Sound Amplifier (PSA)
HA1000 User’s Guide
Ver 2.2
E-mail. [email protected]
Start searching for Bluetooth in the settings on your smartphone,
then connect the "GENIESOR2 PSA" device.
Press the function button
shortly to use it.
Press the "+" up button long to enter pairing mode.
(The green and red LEDs flash repeatedly)
Amplifies bluetooth sound according to the selected DB.
How to pair a Bluetooth device?
Listening to music or voice call of the Bluetooth device.
Bluetooth mode
SHORT PRESS
> Play / Pause
SHORT PRESS
> Connect
Disconnect
Listening to music Voice call
LONG PRESS
Enter BT Mode LONG PRESS
> Enter Pairing
Mode
Press the function button long to change to
the microphone mode.
Change to microphone mode.
Press and
Turn On
The SVS-T broadcast can be received by pressing
the function button and turning on the power switch.
How to listen to SVS-T.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
CAUTION
HA1000 : 2AS7E-SVS-R
FCC certification number
Size / Weight
Bluetooth / Usable frequency / Modulation
Continuous usage time
Battery capacity / Service temperature
W 28.2 X H 82 X T12.2 [mm], 27g
4.2 / 2,402 ~ 2,480 MHz / FHSS
Max 9 hour / 3.7V 450mAh / -10 ~50 C
To prevent possible hearing damage when using a headset,
do not listen to sound at high volume for long periods.
(1) (2) (3)
LONG PRESS
OVER 2 SEC.
58, Giheung-ro, Giheung-gu, Yongin-si, Gyeonggi-do, 16976, South Korea
Tel. [phone] FAX. [phone]