Vais Technology iVIC-5D User manual

iVIC-5 Installation Manual
VAIS
VAIS
T
T
E
E
C
C
H
H
N
N
O
O
L
L
O
O
G
G
Y
Y
www.vaistech.com
• LEXUS • TOYOTA •
Copyright (C) 2003-2012 VAIS Technology Published December 5, 2012
for 5 Generation of Toyota/Lexus Navigation System
IC
i

DO NOT DISASSEMBLE OR ALTER
Doing so may result in an accident, fire or electric shock.
Do not block your view
Do not mount product or any added audio and/or video equipment where it can block your view through the windshield or
your view of dashboard indicators and displays.
Do not block the airbag
Do not mount product or any added audio and/or video equipment where it can obstruct the operation of the safety device
such as the airbag.
Distraction warning
Do not let product or any added audio and/or video equipment to distract you while you are driving.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL
DO NOT SPLICE INTO ELECTRICAL CABLES
Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of
the wire and result in fire or electric shock .
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS
Cables or wiring that obstruct or get caught on places such as the steering wheel, shift lever, brake pedals, etc. can be
extremely hazardous.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST
Moisture or dust may result in product failure.
HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS
The wiring and installation of this product requires special technical skills and experience.
USE ONLY SPECIFIED ACCESSORY PARTS
Use of other than specified parts may damage product internally.
FOLLOW THE OPERATIONAL AND INSTALLATION MANUALS.
YOU SHOULD READ AND FAMILIARIZE YOURSELF THOROUGHLY WITH THE FOLLOWING INFORMATION PRIOR
TO INSTALLING AND USING THIS UNIT. IN ADDITION, YOU MUST CAREFULLY READ AND FOLLOW THE
INSTALLATION SCHEMATICS/INSTRUCTIONS FOR THE PRODUCT AND THE VEHICLE IN WHICH IT IS BEING
INSTALLED. FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS MAY DAMAGE THE PRODUCT AND THE
VEHICLE, WILL VOID THE PRODUCT WARRANTY, AND MAY VOID THE VEHICLE WARRANTY
CHECK YOUR LOCAL LAWS
Some States/Provinces or other governmental jurisdictions (such as cities) may have laws that prohibit the operation of a
video screen within the sight of the Driver. If you have purchased such a product, you should use the product only in
locations where it is legal to do so, and if you do use the product, set up the screen so it is only visible to passengers.
TROUBLESHOOTING
Should this product fail to operate properly, please contact your Dealer or our Customer Service Department at
[email protected].
Before starting any installation work , you must wait 90 seconds after turning the ignition switch to the LOCK position and disconnecting the negative (-) terminal
from the battery. The supplemental restraint system (airbag) is equipped with a backup power source. If installation work is started less 90 seconds after
disconnection of the negative (-)battery terminal, the SRS may deploy. When the negative (-) terminal cable is disconnected from the battery the clock and audio
systems memory will be erased. Before starting installation work make a record of the clock and audio systems memory settings. When installation is complete,
reset the clock and audio systems to their previous settings . Power tilt, power telescopic steering column, front power seats, power mirrors, and power shoulder
belt anchorage are equipped with a memory function .The rear power seat is not equipped with a memory function. e and they can make a record of the memory
contents, rear power seat is not equipped with the memory function. When installation is complete, it is necessary to readjust the features to their previous settings
Never use a backup power supply (such as another battery) during installation work to avoid losing these memory settings.
WARNING
!
CAUTION
!
Before You Start 2

VAIS TECHNOLOGY SHALL NOT BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT OR
CONSEQUENTIAL DAMAGES OR DAMAGES TO PERSONS OR PROPERTY ARISING OUT OF
THE USE OF THE PRODUCT, OR FOR ANY LOSS OF BUSINESS OR PROFITS, EVEN IF VAIS
TECHNOLOGY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. VAIS
TECHNOLOGY'S LIABILITY FOR BREACH OF WARRANTY SHALL NOT EXCEED THE
PURCHASE PRICE OF THE PRODUCT, NOTWITHSTANDING ANY FAILURE OF THE
ESSENTIAL PURPOSE OF ANY LIMITED REMEDY.
DRIVERS OF THE VEHICLE ARE SOLELY RESPONSIBLE FOR THE SAFE OPERATION OF
THE VEHICLE AND THE SAFETY OF YOU AND YOUR PASSENGERS. FOR SAFETY
PURPOSES, THE FUNCTIONALITY OF THIS PRODUCT SHOULD NOT BE USED WHILE THE
VEHICLE IS BEING DRIVEN. SUCH USE COULD BE A DISTRACTION TO THE DRIVER,
WHICH COULD CAUSE AN ACCIDENT LEADING TO SERIOUS INJURY OR DEATH.
SOME STATES/PROVINCES OR OTHER GOVERNMENTAL JURISDICTIONS (SUCH AS
CITIES) MAY HAVE LAWS THAT PROHIBIT THE OPERATION OF A VIDEO SCREEN WITHIN
THE SIGHT OF THE DRIVER. YOU SHOULD USE THE PRODUCT ONLY IN LOCATIONS
WHERE IT IS LEGAL TO DO SO. ALTHOUGH VAIS TECHNOLOGY STRONGLY
RECOMMENDS THAT THE FUNCTIONALITY OF THIS PRODUCT NOT BE USED AT ANY
TIME WHILE THE VEHICLE IS IN MOTION, IT IS YOUR RESPONSIBILITY TO DETERMINE
WHETHER THE PRODUCT CAN BE LEGALLY USED IN ANY GIVEN LOCATION. ANY USE
OF THE PRODUCT IN ANY LOCATION WHERE IT IS ILLEGAL TO DO SO MAY PROHIBIT
YOU FROM RECOVERING DAMAGES IN THE EVENT OF AN ACCIDENT OR MAY BE
USEABLE AGAINST YOU AS EVIDENCE OF NEGLIGENCE.
IMPORTANT
i
IMPORTANT PLEASE READ!
i
WARNING
!
WARNING
!
Keep in mind, vehicle's navigation touch screen differs from your Android Device touch
screen. Do NOT expect the same touch sensitivity, swipe option, or multi-touch capability
(zoom in, zoom out, and etc).
Swipe option is NOT available for all compatible vehicle's models, use control arrow
buttons to make your selections.
This product mirrors Android Device onto the vehicle's navigation screen. Features,
options, and applications varies by Android Device manufacturers.
DRIVE SAFELY AND FOLLOW TRAFFIC RULES.
VAIS TECHNOLOGY AND/OR ITS OWNERS/EMPLOYEES/SHAREHOLDERS/SUPPLIERS
SHALL NOT BE HELD RESPONSIBLE FOR ANY USE OF THIS PRODUCT OR ANY DIRECT
AND INDIRECT CONSEQUENCES THEREOF. WATCHING THIS SCREEN AND MAKING
SELECTIONS WHILE DRIVING CAN CAUSE A SERIOUS ACCIDENT, DAMAGE, OR BREAK
THE LAW.
IF YOU USE THIS PRODUCT IN YOUR VEHICLE, IT IS YOUR RESPONSIBILITY TO MAKE
YOUR PASSENGERS AWARE OF THE ABOVE WARNING.
WARNING
!
3
IMPORTANT DISCLAIMERS

Connections 4
Connecting iVIC
Used for iVIC
Mode programming
Power and Audio
wiring harness Service
Port
USB 2.0 Host
A/V 2
Port
A/V 1
Port / iPod interface
(if available)
Video 3/Camera Port
(if equipped)
Digital Video
harness
!
This is not Firewire port!
Do not use this connector for any Firewire Devices or
for connection to Firewire port on your computer.
By doing so can permanently damage iVIC.
USB extension cable
(included)
To iVIC
USB Port
Install in easy accessible place
for quick switch between
USB devices
1 2
ON
HDMI
USB
Charging
Port
Vehicle signals port
(if equipped)
IC
i
Bluetooth Module
(if equipped) LED
indicators
!
Warning!
Extension cable installation/usage may prevent iPad,
latest iPod/iPhone devices from charging.

Power and Audio
wiring harness
Bluetooth Module
(if equipped)
VGPU Heatsink
(DO NOT COVER IT!)
Allow free airflow
Digital Video
Harness
(MUST BE CONNECTED)
HDMI Cable
A/V1 Video Harness
or
iPod Interface Harness
USB Cable
(Android device charging ONLY
if applicable)
USB 2.0
Extension Cable
or
iPod Interface harness
A/V2 Video
Harness
(if available**)
Camera + Power
Harness
(if equipped*)
Vehicle Signals
Harness
(if equipped*)
Connections 5
Connecting iVIC
!
USB 2.0 Host connector is used for updates, mass
storage devices, and iPod/iPhone/iPad connection
(if applicable).
Warning!
Extension cable installation/usage may prevent iPad,
latest iPod/iPhone devices from charging.
Wire Harness
Support Bracket
Zip ties

Connections 6
Connecting iVIC
To iVIC
Digital Video
Connector
To Factory
Multi-Display Unit
To Factory
harness
from Navigation ECU
(if present)
Digital Video Harness
(included)
+12V Camera Power Supply
Camera Power Supply Ground
+12V Camera Power Supply
Camera Power Supply Ground
A/V 2
(Audio/Video)
Harness
(NOT INCLUDED)
Video 3 / Camera
Harness
(NOT INCLUDED)
A/V1
(Component Video )
Harness
(NOT INCLUDED)
If Composite is selected in A/V1 source
as Input Signal Type, then you must
use Green connector for Composite Video
Digital Video Cable MUST BE CONNECTED to Factory Multi-Display Unit,
and to iVIC for proper operation of iVIC and factory components.
Navigation ECU (if present),
To iVIC AV2 Port
To iVIC Camera Port
(if equipped)
To iVIC
AV1 Port / iPod interface
Port

Connections 7
Head Unit (Radio Receiver)
Connection diagram used for most 2006-2009 Lexus/Toyota vehicles
Connecting iVIC to head unit (for Lexus/Toyota vehicles)
AA
Factory Audio
harness
(if present)
Plug into
Head Unit
(connector “B”)
12-pin connector
Lexus GX 470 Radio Receiver shown.
Locate connector “A” (12-pin connector) on your Radio.
Connector location on the Radio may be
different from shown above.
To iVIC
Audio Harness (36”)
12 Pin Y-harness
Connecting iVIC to Vehicle GVIF Display Port
To Un-plug any connector do NOT pull it by the wires.
WARNING
!
FACTORY MULTI-DISPLAY ECU
To iVIC GVIF
Display Port
Disconnect Factory Digital Video Cable
(if present) from “Display Port”
and reconnect to iVIC Digital
Video Y-harness.
If Navigation System
and Multi-Display ECU is one piece
then Factory Digital Video Cable
is not present.
iVIC
Digital Video Harness
Digital Video Harness MUST NOT be bended
with less than 1 inch radius.
!
ATTENTION

Installation
We strongly recommend that you install the unit in an easily accessible location, so you can later upgrade
the unit or re-program it in case of incorrect programming.
IMPORTANT
i
8
IVIC-5D Programming (MODE 1)
iVIC-5D programming steps:
@Properly install iVIC-5D unit.
@Put the “Left” programming switch in the “DOWN” position.
@Put ignition switch into the “ACC” position.
@Wait for a long beep followed by a few short beeps. This may take up to one minute.
@Return programming switches to their default position (both switches “UP”).
Wait up to 30 seconds until confirmation beep.
@Put ignition switch into the “OFF” position.
@Wait at least 10 seconds.
@Put ignition switch into “ACC” or “ON” position.
@Check iVIC for functionality
iVIC-5D-PA Programming (MODE 3)
iVIC-5D-PA programming steps:
@Properly install iVIC-5D-PA unit.
@Put both programming switches in the “DOWN” position.
@Put ignition switch into the “ACC” position.
@Wait for a long beep followed by a few short beeps. This may take up to one minute.
@Return programming switches to their default position (both switches “UP”).
Wait up to 30 seconds until confirmation beep.
@Put ignition switch into the “OFF” position.
@Wait at least 10 seconds.
@Put ignition switch into “ACC” or “ON” position.
@Check iVIC for functionality
1 2
ON
Left switch
“DOWN”
Ignition into
“ACC” or “ON”
position
Confirmation beep
(Yellow LED blinks)
Both switches
“UP”
ON
1 2
up to 30 sec Confirmation beep
(Yellow LED blinks)
Ignition into
“OFF” position
up to 10 sec
Yellow LED
1 2
ON
Both switches
“DOWN”
Ignition into
“ACC” or “ON”
position
Confirmation beep
(Yellow LED blinks)
Both switches
“UP”
ON
1 2
up to 30 sec Confirmation beep
(Yellow LED blinks)
Ignition into
“OFF” position
up to 10 sec
Yellow LED

!Velcro Fasteners are not included
!VAIS Technology strongly recommends grounding the unit to the car chassis for best results.
NOTE WARNING
!
We strongly recommend to Ground iVIC to the vehicle’s chassis
i
!
Mounting unit using Velcro fasteners
Carpet or car chassis
“Soft” Velcro Fastener
“Hard” Velcro Fastener
Installation 9
iVIC
Requires free flow of air
over heat sink area!
Keep away from external
heat source.

About iVIC 10
iVIC
Video Graphics Mode
CD-MP3 Emulation Mode
Universal Audio/Video Inputs Android Mode
iVIC-5 CD-MP3 Emulation Manual
iVIC-5 AV Sources Manual iVIC-5 Android Mode Manual
Follow
Follow Follow
CD-MP3 emulation is used for mass storage device integration
or for iPod/iPhone integration (if applicable)
iVIC software update can only be done in CD-MP3 mode.
CD-MP3 Emulation Mode
iVIC-5 CD-MP3 Emulation Manual
Video Graphics Mode
To select Video Graphics mode from
CD-MP3 emulation mode,
press and hold the [SCAN] button.
Switching between “Video Graphics Mode” and “CD-MP3 Emulation”