Vantage Hearth VHA-1156 User manual

INSTALLATION
VANTAGECONTROLS.COM
1061 South 800 East • Orem, Utah 84097 • Telephone [phone] • Fax [phone] TPT NO BOX RETROFIT CLIPS – MODELS: VHA-1156/VHA-1157
Overview
The no-box retrofit clips allow the TPT650 or TPT1040
TouchScreens to be installed without using Vantage’s Rough In
Assembly Kits, MODEL: TPT650-INSTALL-16 or MODEL:
TPT1040-INSTALL-16. Please refer to either of these two
Installation instruction sheets for additional information on
powering and wiring to the TPT650 or TPT1040 TouchScreens.
These retrofit clips have been designed for 1/2” or 5/8” thick
Sheetrock walls.
Installation
Installation of Vantage products should be performed or
supervised by a Certified Vantage Installer. Please study these
instructions before installing
If installing TPT TouchScreens using Vantage’s retrofit clips, it
may be necessary to order additional parts. A complete
installation will also need a power supply and possibly AV
connectors. Additional Vantage part numbers are listed here
for your reference.
1. TPT650 power supply part number: VFA-0005
2. TPT1040 power supply part number: VFA-0007
3. (optional) RJ45 TO RCA MALE AUDIO/VIDEO CABLE part
number: VDA-0176
4. (optional) CABLE CONNECTOR, RJ45 TO RJ45 part
number: VDC-0330
Location/Wiring For All Installations
1. The recommended mounting wall height is six inches above
that of a typical keypad station or approximately 50” to 58”
from the floor to the bottom of the TouchScreen. However,
it may be installed at any height fitting your installation
requirements.
2. Sheetrock cutout must match the WALL BOX WIRING
TEMPLATE for your model. If this card is not available, the
cut out hole measurements for the two models are:
a. TPT650 cut out hole should be exactly
i. 6.875” wide x 5.775” high
ii. 17.46cm wide x 14.66cm high
b. TPT1040 cut out hole should be exactly
i. 10.475” wide x 8.375” high
ii. 26.60cm wide x 21.27cm high
TIP: Paint the cut edges of the sheetrock hole to prevent
sheetrock dust from getting into electronics. This is particularly
advantageous for the TPT650 which has the SD Memory Card
slot in the top of the station.
3. Bend the retrofit clips at the appropriate location for 1/2” or
5/8” thick sheetrock and place them in the left and right
sides of the hole. NOTE: the bent smaller section is on the
outside of the wall; the long continuous section of the clip is
behind the sheetrock.
TIP: Use care when bending the clips. If repeated bending
occurs the clips will break.
4. Power supply is 1 to 1 ratio. Only connect ONE TPT650 or
TPT1040 to any power supply.
a. Mount the POWER SUPPLY at a remote location
b. Use 16/2 American Wire Gauge (AWG) or 18/2AWG
wire
i. 16/2AWG – maximum length 100ft. (30.48m)
ii. 18/2AWG – maximum length 50ft. (15.24m)
c. If the POWER SUPPLY cord is
not long enough, cut the
“barrel” end off – about 5” from
the end of the wire – farthest
point away from the 12VDC POWER SUPPLY. Splice into
the end of the extended wire run at the wall box side.
Splice the other end into the other side of the wire run.
IMPORTANT: Keep polarity the same; notice the original
power cord has white dashed lines on one side. Make
sure your connections are to the same wire at each end
of the two wire splice. The high voltage side of the
POWER SUPPLY must be connected to a reliable earth
ground.
5. Connect the power supply and any AV cables to the back of
the TPT TouchScreen and slide the TouchScreen into the
wall.
6. Using the screws provided, secure the TPT TouchScreen to
the wall – DO NOT OVERTIGHTEN!

39818 Warranty at: http://www.vantagecontrols.com/warranty ©Vantage Controls