Velleman THE TREMOR User manual

WWW.VELLEMANPROJECTS.EU
ASSEMBLY MANUAL MAY 2016
ORDERCODE: K8110
THE TREMOR - TREMOLO EFFECT PEDAL
All manuals and user guides at all-guides.com
all-guides.com

Table of contents
Let’s get started!
What’s in the box 3
Assembly instructions 4
All manuals and user guides at all-guides.com

3
K8110ASSEMBLY MANUAL
WHAT’S IN THE BOX
All manuals and user guides at all-guides.com

4
K8110ASSEMBLY MANUAL
ASSEMBLY INSTRUCTIONS
1. Place the 2 supplied cover stickers as shown in the images below. Note the orientation of the
bottom cover!
All manuals and user guides at all-guides.com

5
K8110ASSEMBLY MANUAL
2. All resistors are placed in the correct order of usage on the supplied tape.
Resistors: R1 to R19
R1R19
Tape order:
R1:330K
R2:470K
R3:330K
R4:470K
R5:390E
R6:10K
R7:100K
R8:470E
R9:470E
R10:1M
R11:10K
R12:4K7
R13:47K
R14:33K
R15:10K
R16:39K
R17:100K
R18:100E
R19:1M
C3:104
C4:104
C9:104
ZD1:3V3
D1:1N4007
All manuals and user guides at all-guides.com

6
K8110ASSEMBLY MANUAL
3. 100 µF axial capacitors: C3, C4 and C9
4. 2 x IC: U1 and U2
Note the orientation of the IC’s!
All manuals and user guides at all-guides.com
all-guides.com

7
K8110ASSEMBLY MANUAL
5. Zenerdiode: ZD1
Note the orientation of the zenerdiode!
ZD...
ZD...
ZD...
All manuals and user guides at all-guides.com

8
K8110ASSEMBLY MANUAL
6. Male connectors: SW1; SW2, RV1; RV2 and RV3
7. Diode: D1
All manuals and user guides at all-guides.com

9
K8110ASSEMBLY MANUAL
8. BC547: T1
BC557: T2
9. Capacitor 471: C1
All manuals and user guides at all-guides.com

10
K8110ASSEMBLY MANUAL
10. Capacitor 473: C6
11. Capacitor 105: C11
All manuals and user guides at all-guides.com

11
K8110ASSEMBLY MANUAL
12. Follow these steps:
A. Bend the pins of the 3mm white LED as shown in the pictures below.
B. Cut a 7mm piece of 2.4mm shrinktube.
All manuals and user guides at all-guides.com
all-guides.com

12
K8110ASSEMBLY MANUAL
C. Slide both the 3 mm white LED and the 3 mm photo transistor in the shrink tube as
shown below. No need to actually shrink the tube. This will act as the lightbridge.
D. Place and solder this assembly in LD2 and P1. Note the orientation of both cathode pins!
All manuals and user guides at all-guides.com

13
K8110ASSEMBLY MANUAL
13. DC jack: J1
14. Capacitor 10µF: C14
Note the polarity!
All manuals and user guides at all-guides.com

14
K8110ASSEMBLY MANUAL
15. 2 x Audio jack: SK1 and SK2
16. 5 mm blue LED: LD1 (do a diode test with a multimeter to nd the blue LED)
Make sure it stands out about 12 mm from the PCB, as shown in the picture!
Note the polarity!
C (-)
All manuals and user guides at all-guides.com

15
K8110ASSEMBLY MANUAL
17. 5 mm white LED: LD3 (do a diode test with a multimeter to nd the white LED)
Make sure it stands out about 12 mm from the PCB, as shown in the picture!
Note the polarity!
All manuals and user guides at all-guides.com

16
K8110ASSEMBLY MANUAL
Turn the PCB around!
18. Capacitor 220 µF: C2
Solder on the bottom side of the PCB!
Note the polarity!
Solder on the bottom side of the PCB!
Note the polarity!
18. Capacitor 10 µF: C5, C7, C8, C12
All manuals and user guides at all-guides.com
all-guides.com

17
K8110ASSEMBLY MANUAL
20. Capacitor 47 µF: C10
Solder on the bottom side of the PCB!
Note the polarity!
21. Capacitor 100 µF: C13
Solder on the bottom side of the PCB!
Note the polarity!
All manuals and user guides at all-guides.com

18
K8110ASSEMBLY MANUAL
22. Trim the leads on the 9 V snapt to 5 cm.
22. Strip and tin both wires
All manuals and user guides at all-guides.com

19
K8110ASSEMBLY MANUAL
23. Place and solder the 9 V snap to the PCB as shown in the images below.
Note the polarity! RED = +, BLACK = -
All manuals and user guides at all-guides.com

20
K8110ASSEMBLY MANUAL
All manuals and user guides at all-guides.com