Vello LED Smart Par1941 User manual

Instruction Manual
PROFESSIONAL SHOW LIGHT
LED Smart Par1941
------------------------------ 2017 Ver08.28-----------------------------------

2
Unpacking: Thank you for purchasing the LED light. Every fixture has been thoroughly tested
and has been shipped in perfect operating condition. Carefully check the shipping carton for
damage that may have occurred during shipping. If the carton appears to be damaged, carefully
inspect your fixture for any damage and be sure all accessories necessary to operate the unit has
arrived intact. In the case damage has been found or parts are missing, please contact the
manufacturer or your dealer for further instructions. Do not return this unit to your dealer without
first contacting.
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE POWERING OR
INSTALLING VELLO SMART PAR1941 WASH. SAVE IT FOR FUTURE REFERENCE.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself;
doing so will void your manufactures warranty. In the unlikely event your unit may require service
please contact the manufacturer or your dealer.
PLEASE recycle the shipping carton when ever possible.
General Instructions: To optimize the performance of this product, please read these
operating instructions carefully to familiarize you with the basic operations of this unit. These
instructions contain important safety information regarding the use and maintenance of this unit.
Features
⚫Multi-Colors
⚫Color Strobe
⚫Electronic Dimming 0-100%
⚫DMX-512 protocol
⚫Master/Slave synchronization
⚫LED operation menu with function
buttons
⚫Daisy Chain Units Together in DMX
Mode
Safety Precautions
⚫To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.
⚫Do not spill water or other liquids into or on to your unit.
⚫Be sure that the local power outlet match that of the required voltage for your unit.
⚫Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to
remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of
electrical shock and fire in case of an internal short.
⚫Disconnect from main power before making any type of connection.
⚫Do not remove the cover under any conditions. There are no user serviceable parts inside.
⚫Never operate this unit when it’s cover is removed.
⚫Never plug this unit in to a dimmer pack.
⚫Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm)
between this device and a wall.
⚫Do not attempt to operate this unit, if it becomes damaged.
⚫This unit is intended for indoor use only; use of this product outdoors voids all warranties.
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain
or moisture.
PLEASE consider that damages caused by manual modifications to the device are not subject
to warranty.

3
⚫During long periods of non-use, disconnect the unit’s main power.
⚫Always mount this unit in safe and stable matter.
⚫Power-supply cords should be routed so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to the point they exit from the unit.
⚫Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See “Cleaning”
for details.
⚫Heat -The appliance should be situated away from heat sources such as radiators, heat registers,
stoves, or other appliances (including amplifiers) that produce heat.
⚫The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in performance.
Set Up:
Power Supply: Before plugging your unit in, be sure the source voltage in your area matches the required
voltage for the fixture, The model is Auto power supply, It is workable in 90-250V/50~60Hz. Please make
sure your unit voltage matches the wall outlet voltage before attempting to operate you fixture.
Connection to the mains
For protection from electric shock, the fixture must be earthed!
Install a suitable plug on the power cord, note that the cores in the power cord are colored according to the
following table. The earth has to be connected!
If you have any doubts about proper installation, consult a qualified electrician.
Core (EU)
Core (US)
Connection
Plug Terminal Marking
Brown
Light blue
Yellow/Green
Black
White
Green
Live
Neutral
Earth
L
N
DMX512 connection
The fixture is equipped with both 3-pin or 5-pin XLR sockets for DMX input and output. The sockets are
wired in parallel.
Only use a shielded twisted-pair cable designed for RS-485 and 3-pin or 5-pin XLR-plugs and connectors
in order to connect the controller with the fixture or one fixture with another.
DMX-output DMX-input
XLR mounting-sockets (rear view): XLR mounting-plugs (rear view):
DMX Linking: To ensure proper DMX data transmission, when using several DMX fixtures try to use the
shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence

4
the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in a
DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX
address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it
is located in the DMX chain.
Building a serial DMX-chain:
Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture. Always
connect one output with the input of the next fixture until all fixtures are connected.
Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120Ω resistor
between Signal (－) and Signal (＋) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.
Operating Modes: You can use the LED light Wash in 4 ways:
⚫Auto Mode - The unit automatically chase through the different colors and built-in programs.
⚫Slave Mode –The unit is available work by slave mode.
⚫DMX control mode - This function allows you to control each individual fixtures traits with a standard
DMX 512 controller.
⚫Sound control-This function allows you activate fixtures by sound.
Chart Size(mm)
DMX Mode: Operating through a DMX controller give the user the freedom to create their own programs
tailored to their own individual needs. This function also allows you to use your fixtures as spot lights.
1. This function will allow you to control each individual fixture’s traits with a standard DMX 512 controller.
2. The LED uses 8/16 DMX channels (RGBW version) to operate. Please see “DMX Values and
Functions” for the DMX traits.
3. To run your fixture in DMX mode, plug in the fixture via the XLR connections to any standard DMX
controller. Set your desired DMX address following the setup specifications that come with your DMX
controller.
Touch Buttons: There are four buttons under the LCD display below:
There are four touch buttons under the LED display: Menu,
Up, Down, Enter. Normally, the LED will display the current
DMX address code of the fixture.At this time, presses up and
down to choose the functions you want.
LED Operation Menu: LED screen with four touch buttons: MENU, UP, DOWN and ENTER.

5
Manu details below:
Main Menu
Value
Functions
001-512
DMX address setting
/
8/16 channels mode selection
00-99
Color selective
000-255
Red intensity
000-255
Green intensity
000-255
Blue intensity
000-255
White intensity
/
Sound
Dimmer curve 1
Dimmer curve 2
Dimmer curve 3
DMX CHANNEL MODE:
Reduced Mode
Standard Mode
Value
Function
1
1
000-255
Master dimmer
2
2
000-010
Off
011-110
Strobe fast-slow
111-115
Open
116-165
Pulse strobe1 slow-fast
166-170
Open
171-220
Pulse strobe 2 slow-fast
221-230
Open
231-245
Random strobe
246-266
Open
3
3
207-255
191-206
184-190
180-183
179
175-178
174
<Color Macro >
Alice Blue
Congo Blue
Dark Steel Blue
Deep lavender
Lilac Tint
Daylight Blue
Flame Red

6
172-173
168-171
162-167
157-161
151-156
149-150
147-148
146
145
142-144
138-141
137
134-135
131-133
129-130
128
127
126
125
123-124
121-122
120
119
118
117
115-116
114
113
112
110-111
100-109
089-099
078-088
068-077
062-067
049-061
046-048
045
035-044
032-034
031
030
029
027-028
023-026
020-022
019
BastardAmber
Deep Orange
Pale Gold
Apricot
Bright Blue
Primary Green
Special lavender
Pale Lavender
Deep Golden Amber
Medium Blue
Bright Pink
Mauve
Dark Green
Leaf Green
Dark Blue
Light Blue
Steel Blue
Med Blue Green
Peacock Blue
Magenta
Dark Pink
Middle Rose
Light Salmon
English Rose
Light Rose
Orange
Deep Amber
Straw
Light Amber
Spring Yellow
Dark yellow green
Just Blue
Sky Blue
Lavender
Light Lavender
Pink Carnation
Medium Pink
Light Pink
Sunrise Red
Dark Amber
Gold Amber
Medium Amber
Fire
Surprise Peach
Straw Tint
Medium Yellow
Black

7
018
017
016
015
014
013
012
011
010
000-009
White 5000°K
White 3700°K
White 7000°K
Magenta
Yellow
Cyan
Blue
Green
Red
No function
4
4
000-255
Auto
5
5
000-255
Red color intensity
6
6
000-255
Green color intensity
7
7
000-255
Blue color intensity
8
8
000-255
White color intensity
*
9
000-255
LED 1 Red color intensity
*
10
000-255
LED 1 Green color intensity
*
11
000-255
LED 1 Blue color intensity
*
12
000-255
LED 1 White color intensity
*
13
000-255
LED 2 Red color intensity
*
14
000-255
LED 2 Green color intensity
*
15
000-255
LED 2 Blue color intensity
*
16
000-255
LED 2 White color intensity
Rigging the fixture
Caution: Fixture may cause severe injuries when crashing down! If you have doubts concerning the safety
of a possible installation, do not install the moving head!
Before rigging make sure that the installation area can hold a minimum point load of 10 times the fixture’s
weight.
When installing the device, make sure there is no highly inflammable material (decoration articles, etc.) in a
distance of min. 1.0 m.
CAUTION!
Use an appropriate clamp to ring the fixture on the truss.
Follow the instructions mentioned at the bottom of the base.
Make sure that the device is fixed properly! Ensure that the structure (truss) to which you are attaching the
fixtures is secure.
Securing the fixture via one safety wire Securing the fixture via two safety wires

8
Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out
periodically to optimize light output.
1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.
2. Clean the external optics with glass cleaner and a soft cloth every 20 days.
3. Always be sure to dry all parts completely before plugging the unit back in.
Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog residue, dust,
dew).
Parameter Description
Power:300W
Voltage:110-250V/50-60Hz
Workign position:Any safe working position
Lamp:High power 9090 LED 4in1(RGBW,15W)*19pcs
Beam angle: 8/25
LED display,
8/16DMX channels
9pcs LEDs and 10pcs LEDs two zones control
Protection Rating:IP20
Control mode: Master/Slave synchronization,Stand-alone
DMX512 control and Music Control
Fixture dimension:338*160*398mm
N.W: 7.2kgs
G.W: 9.5kgs
Note: All information is subject to change without prior notice.
TROUBLE SHOOTING: Listed below are a few common problems the user may encounter, with
solutions.