Verde Energy Group VER-UST2-90 Instruction sheet

Nov21
Product Instructions
CYLON LED Streetlights, VER-UST2-90
USER GUIDE:
The purpose of this user guide is to explain the necessary steps for the proper use of a LED Streetlight and
to assure peak performance of this product. It is intended for use as reference by a fully qualified electrician
or technician. This document should never be considered a substitute for any provision of a regulation or
state and/or local code. Please read this entire manual to fully understand and safely use this product.
Specifications are subjected to change without notice. Please visit www.verdeenergygroup.com for the
most recent technical data.
WARNINGS & DISCLAIMERS
1) The light source of this luminaire shall be only replaced by the manufacturer or his service agent
or a similar qualified person
2) The control gear of this luminaire shall be only replaced by the manufacturer or his service agent
or a similar qualified person
3) Ensure the fixture is fully installed by a suitably-qualified person before switching power on to the
fixture
4) Do no install the fixture in a sealed / enclosed environment
5) Do not cover / mask the fixture
6) Ensure the power is turned off before performing maintenance on the fixture
7) Any part of this fixture considered damaged and/or in need of replacement; it shall be exclusively
replaced by the manufacturer or his service agent or similarly qualified person in order to avoid a
safety hazard. Please refer to VERDE LED standard Warranty document for full Terms & Conditions
8) The terminal block is not included with the fixture. Installation may require advice from a suitably
qualified person
9) Always replace any cracked/damaged protective shield
10) This fixture is suitable for indoor and outdoor use
11) These LED street lights meet the Photobiological Safety Standard IEC 62471:2006
12) Specifications and Instructions may change without notice
13) All VERDE products comply with surge immunity as specified by EN 61547:2009. However, the
Verde Warranty also requires additional surge protective devices to be installed on-site against the
effects caused by remote lightning strikes, inductive or capacitive coupling, and switching surge
voltages. These are typically also installed at the main distribution and sub-distribution panels and
are to be maintained and operational always. Refer to industry experts such as
www.phoenixcontact.com for further surge protection advice.
14) This product contains a light source of energy efficiency class ‘’D’’

Nov21
TECHNICAL PARAMETERS:
MODEL
VER-UST2-90
Input Voltage / Frequency
200-240VAC (50/60Hz)
Power
90W
LED Colour Temperature
3000K
Colour Rendering Index
≥70
Light Distribution
152° x 87°
Operating Temperature
-40°C – +45°C
Operating Humidity
10% - 90% RH
Storage Temperature
-40°C – +50°C
Lifespan
L70B10 >50,000 Hrs
Shell Material
Aluminium
IP Rating
IP66
Pole Diameter Size
60mm (default)
Adjustable angle
±15°
Mounting Height
6-8m
Maximum Projected Area
subjected to Wind Force
0.075m2
PHYSICAL DIMENSIONS:
MODEL
Product Dimensions
(a x b x c x d)
VER-UST2-90
740x285x610x132mm

Nov21
INSTALLATION PROCEDURE:
When connecting mains to terminal box, ensure connection employs sufficient strain relief and complies
fully with EN 60998-2-1 or EN 60998-2-2;
Terminal Box Specification:
•Type: (screw or screwless)
•Number of terminals: 2 poles
•Nominal voltage: Max.250 Vac
•Max. Capacity: 0.75-2.5 mm2
After connection to the Terminal Box, affix lamp to pole arm and tighten fastening bolts to a torque of 17N.
ADJUSTMENT:
To adjust the beam orientation of the streetlight:
1. Loosen the two screw.
2. Align the angler triangle pointer to the required angle (from -20° to +15°), then tighten the
screws.
3. It can be installed horizontally and vertically.

Nov21
NEMA MODULE (OPTIONAL):
1) Insert NEMA photocell into the socket on top of fixture (toolless). Rotate in place to ensure
electrical connection
IMPORTANT NOTE: If photo-control is not required, but the fixture has a photocell socket, then a
NEMA blank photocell is still required to complete the electrical connection. These are not supplied,
but are widely available from electrical wholesalers. Alternatively, it can be supplied by VERDE on
request.
MAINTENANCE:
1) Intermittent cleaning will extend the lifetime and safety of your product
2) Clean the product with soap water, then dry with a clean, non-abrasive, cloth
3) Do not use chemicals to clean the product as this may cause corrosion