Verint S5020BX-DN User manual

All users should read the related user manuals for complete details on installation, usage and functionality.
Quick Installation Guide
S5000 Series - BX Models
Version 1.0
Nextiva
1
Hardware Overview
The Nextiva S5000BX is available in two models S5003BX-DN and S5020BX-DN. The S5003BX-DN
features a VGA sensor and the S5020BX-DN features a 2-Megapixel sensor.
Lens are not included with the camera, but Verint offers multiple lenses that are available for purchase. If
you choose to purchase a lens elsewhere, ensure it has the following characteristics:
Aspherical
CS mount, 1/3 inch format
Manual or DC auto iris
Day/Night support
Light Sensor Built-in
Microphone
SD/SDHC
Card Slot
Audio/Video out,
1/8in (3.5mm) jack
Status LEDs
External
Microphone In
12V DC
Power Cord
Connector
NTSC/PAL
Switch
External/Internal
Mic Switch
RJ-45 Network
Connector
DC-Iris Control
Cable Connector
Hardware Reset
Button
12V DC Output
Relay Output
Dry Contact Input Ground 24V AC Input
RS-485 +
RS-485 -
Focus Controller*
Zoom Controller*
Auto Iris Cable
Front View Rear View
*The position of the zoom and focus controllers will vary depending on
the lens manufacturer.

2
Installing the Nextiva S5000BX Models
This section explains how to mount and connect a lens onto the Nextiva S5000BX models.
CAUTION: Verint will not be held liable for damages to persons or property due to the improper installation
of the Nextiva S5000 series IP cameras.
To mount the lens:
1. Mount the lens by turning it clockwise onto the camera mount until it stops.
2. Connect the lens cable plug to the camera DC-Iris Control connector.
Setting the Video Standard
The Nextiva S5000FDW can run in one of two video standards (NTSC or PAL).
To set the video standard:
1. Move the DIP switch to NTSC or PAL.
Connecting the Nextiva S5000BX Models
This section explains how to connect the power and network cables to the Nextiva S5000BX models. A
power supply is not included with the Nextiva S5000BX models and must be purchased separately.
CAUTION: Never use a PoE power connection and a 12V DC power connection at the same time. This may
damage the device.
To power the Nextiva S5000BX models using a 802.3af compliant PoE kit:
1. Plug a straight-through ethernet cable into the RJ-45 connector on the back of the IP camera.
2. Plug the other end of the cable into a POE ethernet switch or to the Data&PWR port of a POE injector. If
you use a PoE injector, make sure the Data port of the injector is properly connected to the ethernet
switch.

3
To power the Nextiva S5000BX models using a 12V DC power supply:
1. Connect the power supply cable to the camera.
2. Plug an ethernet cable into the RJ-45 connector on the back of the IP camera.
3. Plug the power supply cable to the power outlet.
To power the Nextiva S5000BX models using a 24V AC power supply:
1. Connect the wires from the power supply cable to the 24V AC connector.
2. Plug an ethernet cable into the RJ-45 connector on the back of the IP camera.
3. Plug the power supply cable to the power outlet.
Setting the IP Address
By default, all Nextiva S5000 series IP cameras are DHCP (Dynamic Host Configuration Protocol) enabled.
If you have a DHCP server, the IP camera will automatically obtain a valid IP configuration. If the DHCP
configuration fails, the IP camera assigns itself a temporary IP address based on the APIPA (Automatic
Private IP Addressing) addressing format.
To set the IP address of the Nextiva S5000 series IP cameras:
1. Download the latest version of SConfigurator from:www.verint.com/manuals.
2. Extract the executable file (SConfigurator.exe) to the desktop of the computer.
3. Double-click SConfigurator.exe to start SConfigurator.
4. In the General tab, click Program Options.

4
5. Select the IP Address of the correct LAN interface (IP Address of the PC) from IP Address of the PC list.
6. Check Detect All Units on LAN.
7. Ensure that the Discovery IP Address is 255.255.255.255; otherwise, click Reset to Broadcast.
8. In the S5000 Authentication section, type the username and password for the Nextiva S5000.
NOTE: The default username and password for the Nextiva S5000 is admin.
9. Click OK.
10.Select the Units tab, then click Discover. In a DHCP environment, the Address column will display the IP
address assigned by a DHCP server. In APIPA mode, the Address column will display an IP address that
begins with 169.254 and the text will be in red.
If the the Nextiva S5000BX model is DHCP enabled, click Configure.
a. In the Unit Name box, type a unique name for the IP camera.
b. In the tree view, expand the Network node and click IP.

5
c. Uncheck Use DHCP if it is selected.
d. In the IP Address box, type the IP address for the IP camera.
e. In the Subnet Mask box, type the address specifying in which subnet the IP address of the device
belongs.
f. In the Gateway box, type the IP address of the server that acts as an access point to another network.
NOTE: You do not need to use a gateway if the IP camera communicates with other devices on the same
subnet.
g. In the Host Name box, type a unique name for the IP camera.
If the the Nextiva S5000BX model is in APIPA mode, double-click the device.
a. Click Yes in the Reconfigure unit dialog box asking you if you want to set a new network configuration
on the unit.
b. In the IP Address box, type the IP address for the IP camera.
c. In the Subnet Mask box, type the address specifying in which subnet the IP address of the device
belongs.

North America:[phone]| CALA: [phone]
Email: vissuppor[email protected]
EMEA: [phone] |Mobile Support:[phone]
Email: [e-mail]|[email protected]
APAC: Hong Kong: [phone] |Singapore: [phone]
Email: AP[email protected]
© 2010 Verint Video Intelligence Solutions. All Rights Reserved Worldwide. All other trademarks and product names are the property of their respective
owners. Part Number: 23-500-0070-A02
Documentation
To minimize our carbon footprint, we are removing the supporting product
documentation CD that was shipped with our Nextiva Intelligent Edge
Device products. To obtain the latest version of the manuals, please visit:
www.verint.com/manuals
d. In the Gateway box, type the IP address of the server that acts as an access point to another network.
e. You do not need to use a gateway if the IP camera communicates with other devices on the same
subnet.
f. In the Host Name box, type a unique name for the IP camera.
11.Click OK to close the dialog box.
12.Click Exit to close SConfigurator.
Adjusting the Field of View and Focus
Based on the live image retrieved from the IP camera, you can adjust the field of view and focus.
NOTE: The position of the zoom and focus controllers will vary depending on the lens manufacturer.
To adjust the lens zoom factor and focus range:
1. Connect the 1/8in (3.5mm) jack from the Video to BNC connector to the A/V out connector.
2. Connect the BNC connector to a CCTV test monitor.
3. Turn the zoom controller to adjust the zoom factor.
4. While viewing the image on the CCTV test monitor,
turn the focus controller to adjust the focus range.
Related Documentation
Nextiva S5000 Series User Guide
SConfigurator User Guide
Nextiva VMS 6.1 Administration Guide
Nextiva EdgeVR Series 12.4 User Guide
Nextiva Vid-Center 4.3 User Guide
T
W
∞
N