Versa Desk PowerLift PLCSD User manual

REV. 05052021
PowerLift Corner Standing Desk
PLCSD
®
1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
Phillips head screwdriver and/or
hand drill
4mm Allen wrench
(included)
Tape measure
Tools
Parts
Hardware
Leg Foot Side bracket
4-Piece Desktop
x3 x3 x2
Power cordM5x20 Wood Screw
x18
M6x14 Machine screw
DIN6 cableCable clipM5x16 Wood Screw
1/4-20 Phillips Bolt
x28
M6x10 Machine screw
x10
x20x35
x2
x1
x2
Top frame + control box
ControllerS BracketL Bracket Bluetooth App Box Power Strip Link Bracket x4
Front Bracket
3rd Leg Extension

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
M6x14 Machine screw
Slide control box (D) off the frame. Fully separate end frames
(A+C), you will find the center rails (B) inside.
NOTE: End frame C is placed on the side of the desk you plan to mount the control box and controller.
We recommend using the right side.
Place leg into one of the end frames ensuring
brackets are towards the top.
Align holes on leg with holes on end frame and insert
four (4) M6x10 machine screws through the holes in
the end frame and into the leg. Using the supplied
Allen wrench, rotate each screw just a few times.
After all four screws are inserted, tighten all.
Repeat this step for the other pairs of leg and frame.
Slide the side bracket into the end frame.
Insert two (2) M6x14 Machine screws through the
hole on the bottom of the end frame and into the
side bracket. Using the supplied Allen wrench,
rotate each screw just a few times.
After both screws are inserted, tighten both.
Repeat this step for the second leg/frame assembly.
Step 1
Step 2
Step 3
x2
M6x10 Machine screw
x4
BA C
D

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
Attach end frame with L-bracket (A) to end
frame with threaded-inserts (B) using (4)
M6x10 machine screws.
Place desktop with pre-drilled holes and
pre-installed inserts facing up. (We
reccomend placing them on cardboard,
blanket, rug, etc. to protect surface)
Adjust the width of the desk base by
sliding the two end frames outward.
Align the holes on the desk base and
the underside of the desktop.
Attach the desk base to desktop with
eight (8) 1/4-20 Phillips Bolts for the side
bracket holes going into the inserts. Use
four (4) M5x20 Wood Screws for the end
frame holes going into the desktop.
Step 4
Step 6
Step 5
M5x20 Wood Screw
x4
1/4-20 Phillips Bolt
x8
B
A
NOTE: DO NOT tighten all the way yet.
M6x10 Machine screw
x4
Slide the two center rails into the two end frames ensuring:
a) Center rail slots face inward
b) Center rail slots are closer to the top edge
when the assembly is upside down
(as shown in inset)

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
Lock the position of the
center rails using ten (10)
M6x10 machine screws,
ensuring the screws come in
contact with the center rails
by sliding them as needed.
Step 8
M6x10 Machine
screw
x10
Step 7
Ensure there is no gap between surfaces and that the corners of all surfaces allign with
each other by adjusting the end frame with L-bracket (Fig. A)
Tighten the (4) M6x10 machine screws (Fig A.) going through end frame with L-bracket
from Step 4 all the way.
Then, attach (4) link brackets using (6) M5x20 Wood Screws for each bracket.
fig. A
Tighten x4 M6x10 Machine screw
M5x20 Wood Screw
x24

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
For each leg, attach a foot with four (4) M6x14
Machine screws and tighten in a cross pattern.
M6x14 Machine screw
x4
Locate pre-drilled holes toward the front
of the desktop. You can use the set of
holes on either side, but we recommend
using the right side.
Using two (2) M5x16 Wood Screws,
attach the controller to the desktop.
Step 10
M5x16 Wood Screw
x2
Step 11
Slide the control box back onto
the corner end frame. There
are two placement options, we
suggest placing it on the side
closest to your controller.
Step 9

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
Step 12
Using the adhesive back, stick the Power Strip (PS) and BlueTooth App Box (BT) onto the
underside of the desktop as shown below.
Connect cable exiting Leg (closest to control box) directly into the control box (CB). (M1 - red)
Connect 2 DIN6 cables to the other 2 leg cables and then to the control box. (M2&M3 - red+blue)
Connect controller cable and control box to the BlueTooth App Box. (HS - orange)
Connect the power cord to the control box and power strip,
as well as the BlueTooth App Box’s power cord to the power strip. (AC - green)
M1 M2 M3
AC
HS
to outlet
BT
CB
PS
Using the adhesive-back cable clips, secure the cables so they do not sag.
With at least two people, grab the DESK BASE (NOT the desktop) and turn right-side up.
Adjust pre-installed glides on the feet as needed.
Step 13

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
Step 14
Attach L extension bracket with two (2) M6x14 Machine screws.
Step 15
Attach S extension bracket with two (2) M6x10 Machine screws.
x2
M6x14 Machine screw
M6x10 Machine screw
x2

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
Step 16
Slide Front Bracket into place, align the holes with the inserts on the underside of the
desktop and attach with three (3) 1/4-20 Phillips Bolts.
Step 17
Place 4th Surface onto the brackets, align the holes of the Front Bracket woth the
inserts on the underside of the surface and attach with three (3) 1/4-20 Phillips Bolts.
1/4-20 Phillips Bolt
x3
1/4-20 Phillips Bolt
x3

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
Step 18
Secure the surface with six (6) Wood Screws going through the two brackets.
x4
1/4-20 Phillips Bolt