Versiton BAR70-L955 User manual

ADJUST THE DIRECTION & OPEN/CLOSE CAP
INSTALLATION
IR WATERPROOF D&N CAMERA
MANUAL <Ceiling mount>
<Wall mount>
WRENCH 5mm
Wall
※After mounting the camera on a wall or ceiling
1. Loosen a bolt by using the wrench included.
2. Face the direction ofthe camera tomonitor.
3. Tighten a bolt to complete adjustment.
Unlock
Lock
DIRECTION ADJUSTMENT
If you need function setting,
open and close the cap
by using the wrench.
Wall
SCREW Tp16x35 4EA
ANCHOR 8x35 4EA
63
Ø 30
Ceiling
SCREW Tp16x35 4EA
ANCHOR 8x35 4EA
Ø 30
1. Please study the instruction manual before your applications and
keep it for your future reference.
2. Do not flash LED light directly on the eyes when LEDs are on.
3. Do not install the camera on a unstable surface.
It will cause falling or other hazards.
4. Do not use improper power, it could cause fire or electric shock.
(Use the AC adaptor 12V DC regulated, 2A.
Dual voltage product can use 24V AC adaptor.(option))
5. Do not disassemble or re-model the camera, it could cause fire,
electric shock or other hazards.
6. Stop using the camera when you find a malfunction like smoke or
unusual heat, it could cause fire or electric shock.
7. Due to the possibility of water leakage, do not cut or peel off the
cable. In case you cut or peel off the cable, the warranty will be
void.
8. Do not adhere dangerous articles to the camera.
9. Do not leave the unit along with an unstable stand or table.
10. DC power cable or video cable should be always loose.
Do not keep the cables tight or twisted.
11. Please use the camera unit within given temperature and elec-
tricity limit.
12. Please make sure that installation should be done by qualified
service person only.
13. Do not disassemble the unit by yourself. When there is problem
with the unit please contact after-sale service center or the shop
where you bought.
1. New generation, new technology DSP adopted
2. This product is suitable for 24 hours survillance with optical multi-
coating filter according to IR LED and CCD.
10. This camera has vari-focal IR lens to prevent defocusing under IR
lighting.
19. You can adjust the level of IR LED according to the circumstances.
25. Dynamic IR : When IR LED is turned on in B/W, the objects can be
clearly identified due to the function that decreases screen saturation
of objects within a short distance.
3. Long visible range at night.(f = 5~50mm)
4. This camera adopts split glass technology to preventIR light reflection.
5. Day & Night Function(ICR) at night to receive maximum available light.
6. This product can match for any circumstances very well.
7. This product is "waterproof" to resist rain, snow and other weather
factors.(IP67)
8. Sunvisor ofthis product can help the camera get the picture clearly.
9. This product is made of corrosion-free surface to resist rust and
corrosion for a long time.
11. RS-485 interface(Pelco-D, Pelco-P protocol support)- Option
12. Support 8 different privacy zone
13. Adopted 3D DNR technology, It reduces noise efficiently in low light
condition.
14. Multi-language full OSD support
15. Power & video cables are concealable.(Cable through bracket)
16.Thiscamera adopts 3-axis bracket to install on the ceiling and wall.
17. You can connect 24V AC or 12V DC regardless polarity.(Dual power
version only)
18.This camera supportsthe supreme resolution.(700 TV-Line Color)
21. A fan enables the camera to keep the proper operation when the
LED is ON.
22. Provide Max. 10x digital zoom
23. LWDR(Low frame Wide Dynamic Range) & DWDR(Digital Wide Dynamic
Range)
24. DIS(DigitalImage stabilizer)relievesany picture tremble due to external
factor such as wind.
20. A heater enables the camera to keep the proper operation at low
temperature.(ON : 23℃, OFF : 28℃)
FEATURE
CAUTION
If the product is to be put out of operation definitively,
take it to a local recycling plant for a disposal which
is not harmful to the environment.
ACCESSORIES
ANCHOR 8x35 4EA
WRENCH 5mm L TYPE 1EA
SCREW 6x35 TP1PAN SUS 4EA
BOLT 1/4"-20UNC L=6, 1EA
BAR70-L955
Aurora

※All specification is subject to change without notice to improve the quality.
SPECIFICATION
Model No.
Image Sensor
Effective Pixel
Cell Size
Scanning System
Sync. Type
Resolution
S/N
Video Output
OSD
Sense up
AGC
DNR(3D)
Gamma
White Balance
Shutter Speed
Backlight
Motion Detection
Privacy Zone
Mirror
Freeze
Day & Night
LED Brightness
DIS
Digital Zoom
Blemish Compensation
Impact Detection
Communication(option)
Lens
Power Supply
Current Consumption
Fan, Heater
Operation Temp.
Preservation Temp.
Dimension
Weight
1/3"SONY SUPER HAD CCD
768(H) X 494(V) PIXEL(NTSC), 752(H) X 582(V) PIXEL(PAL)
6.35 (H)X 7.4 (V)(NTSC), 6.5 (H) X 6.25 (V)(PAL)
2:1Interlace
Internal/ Line-Lock(option)
700 TV-LINE(COLOR), 750 TV-LINE(B/W)
52dB or More(AGC OFF)
1.0 Vp-p(Sync. Negative) Termination 75
γ= 0.45 typ.(0.45, 0.6, 1.0, user)
Yes(Multi Language)
ATW(2,500°K ~ 9,500 ° K)/MANUAL/AWC
1/60(1/50) ~ 1/100,000sec
Auto(Selectable limit 2X~ 256X)/FIXED/OFF
BLC, LWDR,DWDR, HLC(ON/OFF)
LOW/MIDDLE/HIGH/OFF
LOW/MIDDLE/HIGH/OFF
ON/OFF(240 Block)
ON/OFF(8 Zone)
H/V/BOTH/AUTO(option)
ON/OFF
ICR(AUTO, COLOR, B/W)
70pcs(LOW, MIDDLE, HIGH, OFF), Dynamic IR
ON/OFF
ON(10X)/OFF
AUTO/OFF
LOW/MIDDLE/HIGH/OFF
RS-485(Protocol : Pelco D, Pelco P)
Day & Night Vari-focal auto iris lens
12V DC ±10%(24V AC :option)
Max. 1.3A(at 12V DC, 24V AC) : LEDON
Yes
-20℃~ 50℃
-20℃~ 60℃
141.9(W)X 80.2(H) X 183.3(D)mm
Approx. 1.7kg
Ⅱ
㎛ ㎛ ㎛ ㎛
Ω
FUNCTION SETTING
1. OSD menu structure
Zoom & Focus fixing screw
Focal length adjustment direction
1. Unfasten the '+' type screw inside
2. Adjust two trimmers properly
3. Tighten the scew
When you tighten the screw,
don't put stress excessively.
<Caution>
0.01Lux(F/1.2), 0.0003Lux(Sense up),
0Lux(70M Range at LED HIGH) - Indoor
Min. Illumination
①SET :
② ③ :
④ ⑤ :
⑥EXT-VIDEO :
⑦DEBUG PORT :
⑧ZOOM,⑨FOCUS
Used to access the menu and confirm selection.
It is used for upgrading the product function and
after-sales services.
:Use a '+'type driver for adjusting zoomand focus.
UP, DOWN
LEFT, RIGHT
Used to move the cursor to up or down.
Used to move the cursor to left or right and change
the value.
Extra video output terminal for installation.
Plug your test monitor in hear. The cable is option.
2. OSD menu structure
ㆍThe ' ' icon appeared with desired function, press the set button to move sub menu.
ㆍThe '- - -'icon appeared with function thatis unavailable according to function setting.
3. How to control through RS-485 communication(option)
4. Cable array(option)
1) Match the camera with controller's ID, baudrate and protocol
2) Up, Down, Left and right of Jog lever is same as Up, Down, Left and
right of RS-485 controller
3) Enter of Jog lever is the same as menu key or IRIS open key of RS-
485 controller
A : BLUE(MOTION)
B : BLACK(GND)
C : GREEN(IMPACT)
D : BLACK(GND)
E : ORANGE(RX +)
F : WHITE(RX -)
MOTION ALARM
GND
IMPACT ALARM
GND
RX +
RX -
A
B
C
D
E
F
FUNCTION
ㆍIf the camera detected motion when using Motion & Impact
function, outside line of motion alarm connect with GND(B).
ㆍIf the camera detect impact, outsie line of impact alarm connect
with GND(D).Outputs ofMotion & Impact are 'open collector'.
ㆍMax current & voltage are 200mA and 30V DC.
RS-485A
RS-485B
REMARK
No.
0~99
AUTO
OFF, LOW,
MIDDLE, HIGH
OFF,
X2~X256
OFF, ON
0~20
OFF, ON
OFF, LOW,
MIDDLE, HIGH
OFF, ON
0~60
OFF, ON
0~20
ATW
MANUAL
AWC↓
0~255
0~255
0~255
0~255
AUTO
COLOR
B&W
65~ 160
30~125
3~12
OFF, ON
OFF, LOW,
MIDDLE, HIGH
OFF,
MODE1,
MODE2
OFF,
VERT,
HORI,
BOTH,
AUTO(option)
0~49
OFF, ON
OFF, ON
0~50
OFF, ON
X1.0~X10
-128~ 127
-110~109
OFF, ON
OFF, ON
NONE
MESSAGE
0~120
1~15
OFF, ON
1~15
Fixed focal lens or Vari-focal auto iris lens
Adjust the brightness
Shutter speed auto adjustable
Select shutter speed manually
Determines that use the AGC function or not
and AGC level selectable(You can not use the
Auto D&N change mode when AGC is off)
Using sense up when it is low luminance(OFF,
x2~ x256 selectable)
BLC function
Adjust BLC level
Select LWDR
Digital Wide Dynamic Range
High Light Mask function
According to the threshold value, the camera
will recognize as High light or not.
Reduce noise in low illumination
Level is selectable
Color temperature 2500 ~ 9500°K
Adjust the Red or Blue values
Move the camera lens toward to white paper
then press the set button to find the optimal
white balance for current environment
Adjustthe Red value to shift the color ofthe object
Adjust the Blue value to shift the color ofthe object
Adjust Red tone of the image
Adjust Blue tone ofthe image
Auto day&night switching mode
Fixed at color(LED OFF)
Fixed at B/W(LED level selectable)
Select brightness of illumination about changing
the day ↔night mode
Select the duration time about changing the
day ↔night mode
Determines whether to transmit the burst signal
or not in B/W mode
IR LED OFF/ON and output level adjustable
When IR LED is turned on in B/W, the objects
can be clearly identified due to the function
that decreases screen saturation of objects
within a short distance.
VERT : Set a vertical image inversion
HORI : Set a horizontal image inversion
BOTH : set a image rotation
AUTO :Automatically rotate the screenaccording
to the camera's position
Sharpness adjustable
Gamma adjustable
Get a still image
Determines whether to use the brightness
compensation offour lens'corners(LSC)or not
The LSC level selectable
Max 10x digital zoom available(Default value isX3)
Digital zoom adjustable
Zoomed in image can be moved to horizontal
Zoomed in image can be moved to vertical
This function can be m
itigates image movement
from external factors(This function uses digital
zoom)
Determines whether to use the motion detection
function or not
No display on the screen though movement is
detected
The words 'MOTION'appear on the screen when
movementis detected
Motion detection sensitivity
Setthe duration of alarmout. Ifthe way ofdisplay
is message,it means display time ofmessage
Determines whether to use impact detection
function or not
Sensitivity setting
Set the duration of alarm out and display time
of "IMPACT"message
LENS
LEVEL
E.SHUTTER
AGC
SENSE UP
BLC
LEVEL
LWDR
DWDR
HLC
LEVEL
DNR
LEVEL
WB MODE
R-Y GAIN
B-Y GAIN
D&N MODE
DELAY TIME
BURST
LED LEVEL
DYNAMIC IR
FLIP
SHARPNESS
GAMMA
FREEZE
LSC
LEVEL
DZOOM
ZOOM
PAN
TILT
DIS
MOTION
DISPLAY
SET
WINDOW
ALL SET↓
SENSITIVITY
HOLD TIME
IMPACT
SENSITIVITY
HOLD TIME
Function
setting menu Select menu ContentsSub menu
1/60(1/50)~1/100,000
MANUAL , DC
MANUAL BLUE
MANUAL RED
BW COLOR→
COLOR BW→
0.45, 0.6, 1.0, USER
LOW, MIDDLE, HIGH
ALL CLEAR↓
1. EXPOSURE
3. DAY&NIGHT
4. IMAGE ADJ.
2. WHITE
BALANCE
5. ALARM
Press the set button to move into the motion detection area section
to set the 240 blocks. To escape this menu, you should press the
left button at the far left or press the right button at the far right
Press the set button to select all area
Press the set button to remove all area
Test signal. Press the setbutton, color bar appeared on the screen
and press any key to return to menu
PATTERN
GENERATOR
Display each privacy mask or not.
Select mask color(8 color is available)
Select language
Display the camera ID on the screen
Defectpixel correction in low illumination
Setup the limited value ofwhite pixel correction
Setup the limited value of black pixel correction
Setup the DPC(Defect Pixel Correction) level
Internal Sync with 12V DC power
Setting the phase is selectable when used
24V AC(Dual power only)
Phase contollable at 24V AC input(L/L mode)
Monitor setting
Select the camera ID for RS-485 communication
Select baud rate
Select protocol
OFF, ON
BLACK, GRAY…
ENGLISH, …
OFF, ON
OFF, AUTO
0~255
0~255
0~255
INT
L/L
0~255
CRT, LCD
1~255
MASK 1~8
SET
WINDOW
COLOR SET
LANGUAGE
TITLE
EDIT
RESET↓
POSITION
DPC
WHITE THR
BLACK THR
DPC LEVEL
SYNC
VPHASE
MONITOR
COM. ID
BAUDRATE
PROTOCOL
FACTORY
SET↓
EXIT↓
RETURN
Reset your camera to factory default condition and then restart
Notice : Lens, communication and language is not changed
Save the value and then restart
Escape the menu without save
Move back to previous menu
Camera ID setting
Camera ID reset
Camera ID position
Communication setting
Press the set button at first time, you can move the mask's
position. After press the set button again, you can adjust the size
of mask. If you press the set button once more, you can adjust
position of edge. After decided position of edge then press the
set button, it will be back to previous menu.
7. SPECIAL
6.PRIVACY
ZONE
8. EXIT
2400, 4800, 9600
PELCO-D, PELCO-P
COMMUNICATION
SAVE AND EXIT↓
6 7
8 9
1
2
4
3
5
BAR70-L955