Versiton BAR70 M855 User manual

ADJUST THE DIRECTION & OPEN/CLOSE CAP
INSTALLATION
1. Please study the instruction manual before your applications and
keep it for your future reference.
2. Do not flash LED light directly on the eyes when LEDs are on.
3. Do not install the camera on a unstable surface. It will cause falling
or other hazards.
4. Do not use improper power, it could cause fire or electric shock.
(Use the AC adaptor 12V DC regulated, 2A.
Dual voltage product canuse 24V AC adaptor.(option))
5. Do not disassemble or re-model the camera, it could cause fire,
electric shock or other hazards.
6. Stop using the camera when you find a malfunction like smoke or
unusual heat, it could cause fire or electric shock.
7. Due to the possibility of water leakage, do not cut or peel off the cable.
In case you cutor peel offthe cable, the warranty will be void.
8. Do not adhere dangerous articles to the camera.
9. Do not leave the unit along with an unstable stand or table.
10. DC power cable or video cable should be always loose.
Do not keep the cables tight or twisted.
11. Please use the camera unit within given temperature and electricity
limit.
12. Please make sure that installation should be done by qualified
service person only.
13. Do not disassemble the unit by yourself. When there is problem
with the unit please contact after-sale service center or the shop
where you bought.
ACCESSORIES
IR WATERPROOF D&N CAMERA
MANUAL
1. Long visible range at night.(70m Max. indoors, 60m Max.outdoors)
2. You can select the level of LED ON/OFF and filter change according
to Lux as follow.
- Default Setting LED ON : Approx.5Lux,LED OFF : 10Lux
3. This camera adopts splitglass technology to preventIR light reflection.
4. This camera has vari-focal IR lens to prevent defocusing under IR
lighting.
5. Day & Night Function(ICR) at night to receive maximum available light.
6. This product can match for any circumstances very well.
7. This product is suitable for 24 hours survillance with optical multi-
coating filter according to IR LED and CCD.
8. This product is "waterproof" to resist rain, snow and other weather
factors.(IP67)
9. Sunvisor of this product can help the camera get the picture clearly.
10. This product is made of corrosion-free surface to resist rust and
corrosion for a long time.
11. RS-485 interface.(Pelco-D, Pelco-P protocol support)
12. Support 4 different privacy zone
13. DWDR(Digital Wide Dynamic Range)
14. Multi function :High Light Mask, Lens Shading Compensation, Impact
Detection,Motion Detection
15. Multi-language full OSD support
16. Power & video cables are concealable.(Cable through bracket)
17. This camera adopts 3-axis bracket to install on the ceilingand wall.
18. You can connect 24V AC or 12V DC regardless polarity.
19. This camera supports the advanced high resolution.
(700 TV- Line Color)
20. You can adjust the level of IR LED according to the circumstances.
IR LED output level controllable via RS-485.
21. A heater enables the camera to keep the proper operation at low
temperature.(ON : 23℃, OFF : 28℃)
22. A fan enables the camera to keep the proper operation when the
LED is ON.
Approx.
(Dual power version only)
FEATURE
CAUTION
If the product is to be put out of operation definitively,
take it to a local recycling plant for a disposal which
is not harmful to the environment.
ANCHOR 8x35 4EA
WRENCH 5mm L TYPE 1EA
BOLT 1/4"-20UNC L=6, 1EA
SCREW 6x35 TP1PAN SUS 4EA
<Ceiling mount>
<Wall mount>
WRENCH 5mm
Wall
Unlock
Lock
DIRECTION ADJUSTMENT
If you need function setting,
open and close the cap
by using the wrench.
Wall
SCREW Tp16x35 4EA
ANCHOR 8x35 4EA
63
Ø 30
Ceiling
SCREW Tp16x35 4EA
ANCHOR 8x35 4EA
Ø 30
※After mounting the camera on a wall or ceiling
1. Loosen a bolt by using the wrench included.
2. Face the direction ofthe camera to monitor.
3. Tighten a bolt to complete adjustment.
BAR70-M855

2. How to use the jog lever & Zoom/Focus trimmer
3. How to control through RS-485 communication
4. Cable array
①Enter :
ㆍ
ㆍ
②UP, ③DOWN
④LEFT, ⑤RIGHT
⑥EXT. VIDEO
⑦Zoom, ⑧Focus
Push the lever : Used to access the menu and confirm selection.
Push the lever for one second : Used to return to previous menu
from the motion detection setting section or privacy mask setting
section.
: Used to move the cursor to upor down.
: Used to move the cursor to left or right and
change the value.
: Extra video output terminal for installation.
Plug your test monitor in hear. The cable is option.
: Use a '+' type driver for adjusting zoom and
focus.
1) Match the camera with controller's ID, baudrate and protocol
2) Up, Down, Left and right of Jog lever is same as Up, Down, Left
and right of RS-485 controller
3) Enter of Jog lever is the same as menu key or IRIS open key of
RS-485 controller
4) Return to previous menu from motion detection setting section
and privacy mask setting section : Iris close or Iris open for a
few second. Or press the button as Up →Right →Down →
Left successively
(RS-485, ALARM)
<Caution>All connectors must be securely sealed to prevent water leakage, especially
for un-used wires.
※All specification is subject to change without notice to improve the quality.
1/3"SONY SUPER HAD CCD
768(H) X 494(V) PIXEL(NTSC), 752(H) X 582(V) PIXEL(PAL)
6.35㎛(H) X 7.4㎛(V)(NTSC)
, 6.5㎛(H) X 6.25㎛(V)(PAL)
COLOR : 700 TV-Line, B/W :750 TV-Line
NTSC / PAL
Internal
2:1Interlace
1.0 Vp-p(Sync. Negative) Termination 75Ω± 10%
γ= 0.45(Adjustable)
0.01Lux(F/1.2), 0Lux(LED HIGH, 70M Range)
Full OSD
ON / OFF Selectable(64 Zone)
ON / OFF Selectable(3 Step : LOW / MIDDLE / HIGH)
ATW / AWC / MANUAL
ON / OFF Selectable(4 Zone)
ICR(AUTO, COLOR, B/W)
PELCO-D&P
48dB over(AGC OFF)
ON / OFF
DWDR / BLC / HLC / OFF
YES
Extra Video connector for easy installation
Automatic(Adjustable)
1/60 ~ 1/100,000sec(NTSC), 1/50 ~ 1/100,000sec(PAL)
Average test illuminance by front view
12V DC, 24V AC Dual Voltage(option)
Max. 1.3A
Vari-focal auto iris day & night lens
IR LED 70EA
-10 ∼50℃
-20 ∼60℃
141.9(W) X 80.2(H) X 183.3(D)mm
Approx. 1.7kg
Ⅱ
Model No.
Image Sensor
Effective Pixel
Cell Size
Resolution
TV Type
Sync. Type
Scanning System
Video Output
Gamma Characteristic
Min. Illumination
OSD
Motion Detection
Impact Detection
White Balace
Privacy Zone
Day & Night
RS-485 Protocol
S/N Ratio
Mirror
Backlight
Control Interface
Gain Control
Shutter
Test Illuminance Area
Power Supply
Current Consumption
Lens
LED
Operation Temp.
Preservation Temp.
Dimension
Weight
Reverse Polarity Protection
SPECIFICATION
A : BLUE(MOTION)
B : BLACK(GND)
C : GREEN(IMPACT)
D : BLACK(GND)
E : ORANGE(RX +)
F : WHITE(RX -)
MOTION ALARM
GND
IMPACT ALARM
GND
RX +
RX -
A
B
C
D
E
F
FUNCTION
ㆍIf the camera detected motion when using Motion & Impact
function, outside line of motion alarm connect with GND(B).
ㆍIf the camera detect impact, outsie line of impact alarm connect
with GND(D).Outputs ofMotion & Impact are 'open collector'.
ㆍMax current & voltage are 200mA and 30V DC.
RS-485A
RS-485B
REMARK
No.
Focus & Zoom fixing screw
Focal length adjustment direction
1. Unfasten the '+' type screw inside
2. Adjust two trimmers properly
3. Tighten the scew
When you tighten the screw,
don't put stress excessively.
<Caution>
FUNCTION SETTING
1. OSD menu structure
Color temperature 2500 ~ 9500°K
Adjust the Red or Blue values to shift the color
of the object
Move the camera lens toward to white paper
then press the set button to find the optimal
white balance for current environment
Auto day&night switching mode
Fixed at color(LED OFF)
Fixed at B/W(LED ON)
Determines whether to transmitthe burst signal
or not in B/W mode
You can select brightness of illumination about
changing the day ↔night mode
You can select the duration time about chaining
the day ↔night mode
IR LED OFF/ON and output level adjustable
When IR LED is turned on in B/W, the objects
can be clearly identified due to the function
that decreases screen saturation of objects
within a short distance.
Set a horizontal image inversion
Sharpness adjustable
Gamma adjustable
Determines whether to use the brightness com-
pensation of four lens'corners(LSC) or not
The LSC level selectable
Adjust Red tone of the image
Adjust Blue tone of the image
Determines whether to use the motion detection
function or not
No display on the screen though movement
is detected
The words 'MOTION' appear on the screen
when movement is detected
Motion detection area appear on the screen
when movement is detected
Motion detection sensitivity
Set the duration of outside alarm. If the way of
display is message, it means display time of
message
Determines whether to use impact detection
function or not and sensitivity setting
Set the duration of outside alarm and display
time of "IMPACT"message
Display each privacy mask or not. Press the
set button to move into the privacy mask
setting section, whenever you press the set
button, the mask color is changed. When the
mask color is red you can adjust the size by
up, down, left and right button. When the
mask color is blue you can set the position of
mask by up, down, left and right button. Press
the set button for a few second to escape
Select mask color
Select the camera ID for RS-485 communication
Select baud rate
Select protocol
Select language
Display the camera ID on the screen
ATW
MANUAL
AWC↓
AUTO
COLOR
B&W
OFF, ON
85 ~ 170
50 ~ 135
3 ~ 15
OFF, ON
OFF, ON
0 ~ 50
OFF, ON
0 ~ 50
0 ~ 200
0 ~ 200
OFF, ON
NONE
MESSAGE
MASK
0 ~ 255
1~ 15
OFF, LOW,
MIDDLE, HIGH
1~ 15
OFF, ON
1~ 255
2400 ~ 9600
ENGLISH, …
OFF, ON
Press the set button to move into the motion detection area
section to set the 64 areas. Press the set button for a few second
to move out
Press the set button to select all area
Press the set button to remove all area
AWB MODE
D&N MODE
DYNAMIC IR
MIRROR
SHARPNESS
GAMMA
LSC
R-Y GAIN
B-Y GAIN
MOTION
IMPACT
MASK
1, 2, 3, 4
CAM ID
BAUDRATE
PROTOCOL
LANGUAGE
BURST
DELAY TIME
LSC LEVEL
DISPLAY
SET
WINDOW
ALL SET↓
SENSITIVITY
HOLD TIME
HOLD TIME
EDIT
POSITION
6. PRIVACY
MASK
7. COMMUNI-
CATION
10. EXIT
9. FACTORY
SET
5. MOTION &
IMPACT
4. IMAGE
ADJUST
3. DAY&NIGHT
PELCO-D, PELCO-P
MASK COLOR
NAME DISPLAY
BLACK,GRAY…
8. SPECIAL
2. WHITE
BALANCE
ALLCLEAR↓
COLOR B&W
B&W COLOR
→
→
OFF, LOW, MIDDLE, HIGH
LED LEVEL(IN/OUT)
PATTERN
GENERATOR
Test signal. Press the setbutton, color bar appeared on the screen
and press any key to return to menu
Press the set button to move into the name setting section. You
can choose the letter by using up and down button and move
next letter by using left and right button. Press the set button for
a few second to move out
Press the set button to move into the position setting section.
You can move the camera ID to your wanted position by using
up, down, left and right button
※If you change the COMMUNICATION value through RS-485, you might not
control the camera due to unmatched value(If your camera is out of working
due to above reason, change your controller's value or wait a few minute till
close the menu, it will be back to previous setting value)
To reset your camera to factory default condition
Notice : Lens, communication and language is not changed
Save the value and then restart
0.45, 0.6, 1, USER
Fixed focal lens or Vari-focal auto iris lens
In case of manual lens selection, adjust the
brightness
In case ofDC lens selection,adjust the bright-
ness
Shutter speed auto adjustable
Select shutter speed manually
Determines that use the AGC function or not
and AGC level selectable(You can not use the
Auto D&N change mode when AGC is off)
Digital Wide Dynamic Range
BLC function
High Light Mask function
In case of AUTO mode, the function will off in
daytime and on at night
According to the threshold value,the camera
will recognize as High light or not.
LENS
E.SHUTTER
AGC
DWDR
BLC
HLC
BRIGHT
DC LEVEL
HLC THR
MANUAL, DC
0 ~ 100
0 ~ 20
AUTO
OFF, LOW,
MIDDLE, HIGH
OFF, ON
OFF, ON,
AUTO
0 ~ 100
1. EXPOSURE
1/60(1/50) ~ 1/100,000
Function
setting menu Select menu ContentsSub menu
OFF, LOW, MIDDLE, HIGH
6
7 8
1
2
4
3
5
BAR70-M855