Vezco VZ-TVI-B2040VF User manual

VZ-TVI-B2040VF
HD1080P Vari-focal IR
Bullet Camera
User Manual
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested
and found to comply with the limits for a digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the user
will be required to correct the interference at his
own expense.
FCC Conditions
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
EU Conformity Statement
1Introduction
1.1 Product Features
This series of camera adopts new generation
sensor with high sensitivity and advanced circuit
design technology. It features high resolution, low
image distortion and low noise, etc., which
makes it suitable for surveillance system and
image processing system.
• High performance CMOS sensor and high
resolution bring high-quality image;
• Low illumination;
• O S D me nu , pa r a meter s are c onf ig u r ab le;
• Support auto white balance, auto g a in c on tr o l,
electronic shutter control;
• Support image e ff ect adjus tment;
• Unit tr ansmission c on tr o l;
• Adv anced 3-a xis design meet s dif f erent
installation requirements.
Cameras in some models do not support OSD
menu. For actual operation, please refer to the
specification of each model.
1.2 Overview
1.2.1 Overview of Type I Camera
2Installation
Before you start:
• Ple as e m a ke su re t ha t t h e d evice i n t h e pa ck a ge is
in good condition and all the assembly parts are
included.
• Make su re t ha t all t h e rel a te d e qu i p me n t i s
power-off during the installation.
• Ch eck t h e sp eci f ic a ti on of t h e p r odu ct s fo r t h e
installation environment.
• Check whether the pow er supply is matc hed
with your power output to avoid damage.
• Please make sur e the w a ll is s tr ong enough t o
withstand three times the weight of the camera
and the mounting.
• I f t h e w a ll i s t h e ceme n t w a ll, y ou n ee d t o i ns ert
expansion screws before you install the camera.
If the wall is the wooden wall, you can use
self-tapping screw to secure the camera.
• If the pr oduct does not function properly,
please contact your dealer or the nearest
service center. Do not disassemble the camera
for repair or maintenance by yourself.
2.1 Installation of Type I Camera
Steps:
1.Drill the screw holes and the cable hole on the
ceiling according to the supplied drill template.
Thank you for purchasing our product. If there
are any questions, or requests, please do not
hesitate to contact the dealer.
This manual may contain several technical
incorrect places or printing errors, and the
content is subject to change without notice. The
updates will be added to the new version of this
manual. We will readily improve or update the
products or procedures described in the manual.
This product and - if applicable - the
supplied accessories too are marked
with "CE" and comply therefore with
the applicable harmonized European
standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC, the
RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted
Figure 2-1 The Drill Template
Privacy Notice
Surveillance laws vary by jurisdiction. Check all
relevant laws in your jurisdiction before using this
product for surveillance purposes to ensure that
your use of this product conforms.
Please refer to the product specification for
camera parameters and functions.
www.vezcocctv.com
municipal waste in the European
Union. For proper recycling, return
this product to your local supplier
upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more
information see: www.recyclethis.info.
2006/66/EC (battery directive):
This product contains a battery that
cannot be disposed of as unsorted
municipal waste in the European
Union.
See the product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg).
For proper recycling, return the battery to your
supplier or to a designated collection point. For
more information see: www.recyclethis.info.
Figure 1-1 Overview of Type I Camera
1.2.2 Overview of Type II Camera
Figure 1-2 Overview of Type II Camera
2. Push the lock button to disassemble the camera
from the mounting base.
Figure 2-2 Release the Lock Screw
3.Fix the mounting base to the ceiling.
4.Route the cables to the cable hole and connect
the corresponding cables.
5.Secure the camera to the mounting base by
supplied screws. Keep the word UP on the camera
being upright during the installation to make the
image showing normally.

Figure 2-3 Secure the Camera
6.Adjust the camera according to the figure below
to get an optimum angle.
Figure 2-4 Universal Adjustment
7.Use the screwdriver to adjust the ZOOM screw
and the FOCUS screw until you get the optimum
image.
Figure 2-5 Zoom and Focus Adjustment
2.2 Installation of Type II Camera
Both wall mounting and ceiling mounting are
suitable for type II bullet camera. Ceiling mounting
3.Route the cables to the cable hole and connect
the corresponding cables.
4.Fix the camera to the ceiling with the supplied
screws.
Figure 2-7 Fix the Camera to the Ceiling
5. Adjust the surveillance angle.
1). Loosen No.1 adjusting screw to adjust the pan
position (0° ~ 360°).
2).Tighten No.1 adjusting screw.
3). Loosen No.2 adjusting screw to adjust the
tilting position (0° ~ 90°).
4).Tighten No.2 adjusting screw.
5). Loosen No.3 adjusting screw to adjust the
rotation position (0° ~ 360° ).
6).Tighten No.3 adjusting screw.
0~360
1
2
0~90
3 0~360
Figure 2-8 3-axis Adjustment
3Menu Operation
Figure 3-1 Main Menu
With a coaxial camera controller (purchase
separately) or calling the preset No.95 you can
select the menu and adjust the camera parameters.
3.1 FORMAT
You can set the format as PAL/NTSC.
3.2 SET UP
Move the cursor to SET UP, and press menu button to
enter the SET UP sub menu.
3.2.1 AE
Move the cursor to AE, and you can adjust the
image brightness by the BRIGHTNESS, EXPOSURE
MODE, and AGC.
Brightness:
Brightness refers to the brightness of the image.
Exposure Mode:
Move the cursor to Exposure Mode, you can select
the exposure mode between Globe and BLC.
When BLC is selected as the exposure mode, the level
of BLC mode can be adjusted, as shown in the
AWB: white balance is being adjusted
automatically.
MWB: Set the R GAIN/B GAIN value from 1 to 10.
As shown in Figure 3-3.
3.2.3 DAY & NIGHT
Move the cursor to DAY & NIGHT, and select
COLOR, B/W, or SMART as the DAY & NIGHT mode.
COLOR: The image is colored in day mode all the
time.
B/W: The image is black & white all the time, and
the IR LED turns on in the low-light conditions.
SMART: Select to turn on/off the INFRARED_LAMP
and to set the Smart IR level from 1to 16.
As shown in Figure 3-4.
Figure 3-4 DAY/NIGHT
3.2.4 VIDEO SETTING
Contrast:
Contrast enhances the difference in color and light
between parts of an image.
You can set the value from 1 to 10.
Sharpness:
Sharpness determines the amount of detail that an
imaging system can reproduce. You can set the
value from 1 to 10.
Saturation:
You can set the saturation level of the image. The
will be taken as an example in the section. And you
can take steps of ceiling mounting as a reference
if wall mounting is adopted.
Steps:
1. Drill the screw holes and the cable hole in the
ceiling according to the supplied drill template.
2. Hammer the supplied plastic expansion bolt into
the screw holes.
6.Push the focus &zoom adjustment cover upward
to move it aside.
7.Use the cover as a screwdriver to adjust the ZOOM
screw and the FOCUS screw until you get the
optimum image.
Figure 3-2.
Figure 3-2 EXPOSURE
AGC:
Figure 3-3 WB
value is from 0 to 10.
DNR:
DNR decreases the noise effect, especially in low
light conditions and delivers more accurate and
sharp image quality. You can set the value from
0 to 7.
Mirror:
You can set the Mirror status as H, V, HV, or OFF.
3.2.5 Reset
Reset all the settings to the default.
Figure 2-6 Drill Template
Figure 2-9 Zoom and Focus Adjustment
AGC optimizes the clarity of image in poor light
scene. AGC level can be set as OFF, LOW, MIDDLE
and HIGH.
3.2.2 WB
Move the cursor to WB, and you can set White
Balance mode as AWB and MWB in this menu.
3.2.6 EXIT
Exit and Save & exit are selectable.
3.2.7 SAVE/EXIT
Move the cursor to SAVE & Exit, and press OK to
save the settings and exit the menu.
AE
WB
DAY/NIGHT
VIDEO
SETTING
RESET
EXIT SAVE/EXIT
BRIGHTNESS
MODE
CONTRAST
EXPOSURE MODE
INFRARED
SHARPNESS
AGC
SMART IR
SATURATION
DNR
MIRROR
DAY/NIGHT
MODE SMART
INFRARED OFF
SMART IR 0-|--5
RETURN ‘
Focus
Cover
Zoom
Cover
0~360
EXPOSURE
1.BRIGHTNESS 5
2.EXPOSURE MODE BLC
LEVEL 5
3.AGC MIDDLE
4.RETURN
WB
MODE
R GIAN
B GAIN
RETURN
MWB
1-|--10
1-|--10
‘