VHD VHD-J1600SE Instruction Manual

HD Video Conference
DATASHEET - MANUAL
VHD-J1600SE
MAIN FEATURES
• H.265 Support encoding, enabling full HD 1080p/60fps video stream by ultra-low
bandwith, lag-timewithin 200ms.
• 1080P Full HD Apply Panasonic’s 1/2.7 inch, 2.07 million effective pixels high quality HD CMOS
sensor, can reachmaximum 1920x1080 high resolution and achieve quality image.
• Double Interface Support 3G-SDI interface, effective transmission distance up to 150 meters
1080p30). SDI, Network can output at the same time.
• Ultra-high Frame Rate The output frame rate up to 60fps in 1080P, up to 120fps output in 720P
(supported by network only), 640x480P can be as high as 240fps (supported by network only,
optional).
• AAC Audio Encoding audio encoding, better sound quality and smaller bandwidth.
• Low-light High SNR of CMOS sensor combined with 2D and 3D noise reduction algorithm, effectively
reducethe noise, even under low illumination conditions, picture can still keep clean and clear.
• PoE Support (802.3af), effectively reduce the cost of engineering and routing.
• ICR Infrared Filter with auto switch, keep watch over day and night.
• SDK Support, easy to implement the custom requirement.

VHD-J1600SE
DATASHEET - MANUAL
VIDEO SYSTEM
SENSOR
SCANNING MODE
LENS MOUNT
AUTO IRIS
MINIMAL ILLUMINATION
SHUTTER
WHITE BALANCE
DAY-NIGHT MODE
DIGITAL NOISEREDUCTION
BACKLIGHTCOMPENSATION
IMAGE FREEZE
POE
CEILING INSTALLATION
1080P/60, 1080P/50, 1080I/60, 1080I/50, 1080P/30, 1080P/25, 720P/120
(SUPPORTED BY NETWORK ONLY),720P/60, 720P/50, 720P/30, 720P/25,
640X480P/240 (SUPPORTED BY NETWORK ONLY, OPTIONAL)
1/2.7’’, CMOS, EFFECTIVE PIXEL: 2.07M
PROGRESSIVE
C/CS MOUNT
DC DRIVER
1/30S ~ 1/10000S
AUTO, 3000K/INDOOR, 4000K, 5000K/OUTDOOR, 6500K_1, 6500K_2,
6500K_3, ONE PUSH, MANUAL
IR CUT FILTER WITH AUTO SWITCH
2D,3D DIGITAL NOISE REDUCTION
SUPPORT
SUPPORT
SUPPORT
SUPPORT
0.05 LUX @ (F1.8, AGC ON)
CAMERA
INPUT/OUTPUT INTERFACE
HD OUTPUT
NETWORK INTERFACE
AUDIO INTERFACE
POWER CONNECTOR
RESET BUTTON
1X3G-SDI: BNC TYPE, 800MVP-P, 75Ω, ALONG TO SMPTE 424M STANDARD
1XRJ45:10M/100M ADAPTIVE ETHERNET PORTS
1-CH: 3.5MM AUDIO INTERFACE, LINE IN
JEITA (DC IN 12V)
SUPPORT

IPC FEATURES
VIDEO COMPRESSION
VIDEO STREAM
MAIN STREAMRESOLUTION
SUB STREAMRESOLUTION
VIDEO BIT RATE
BIT RATE TYPE
FRAME RATE
AUDIO COMPRESSION
AUDIO BIT RATE
SUPPORT PROTOCOLS
H.265/H.264/MJEPG
MAIN STREAM, SUB STREAM
1920X1080, 1280X720, 1024X576
720X576, 720X480, 320X240
128KBPS ~ 8192KBPS
50HZ: 1FPS ~ 50FPS, 60HZ: 1FPS ~ 60FPS, 720P120: 120FPS,
640X480P240: 240FP
AAC
96KBPS, 128KBPS, 256KBPS
TCP/IP, HTTP, RTSP, RTMP, ONVIF, DHCP, MULTICAST, ETC.
VARIABLE RATE, FIXED RATE
GENERIC SPECIFICATION
INPUT VOLTAGE
CURRENT CONSUMPTION
OPERATINGTEMPERATURE
STORAGE TEMPERATURE
POWER CONSUMPTION
SIZE
NET WEIGHT
MTBF
DC 12V / POE (802.3AF)
0.5A (MAX)
-10°C ~ 40°C (14°F ~ 104°F)
-40°C ~ 60°C (-40°F ~ 140°F)
6W (MAX)
127.5MM X 72.0MM X 60.0MM
375G (0.8LB)
6000H
VHD-J1600SE
DATASHEET - MANUAL

> PACKING LIST
> NOTES
ELECTRIC SAFETY
installation and operation must accord with electric
safety standard.
CAUTION TO TRANSPORT
avoid stress, vibration and soakage in transport,
storage and installation.
POLARITY OF POWER SUPPLY
the power supply of the product is +12v, the max
electrical current is 2a. Polarity of the power supply
plug drawing as follows.
CAREFUL OF INSTALLATION
Do not grasp the camera head when carrying the
camera. Don’t turn camera head by hand. Doing so
may result in mechanical damage. Never power on
before installation is not completed.
DON’T DISMANTLE THE CAMERA
We are not responsible for any unauthorized
modication or dismantl-eing.
CAUTION!
The specic frequency of electromagnetic eld may
affect the image of the camera!
APPEARANCE AND INTERFACE
VHD-J1600SE
DATASHEET - MANUAL
> MAIN FEATURES
H.265 SUPPORT
Support H.265 encoding, enabling full HD
1080p/60fps video stream by ultra-low bandwidth,
lag-time within 200ms.
1080P FULL HD
Apply Panasonic’s 1/2.7 inch, 2.07 million effective
pixels high quality HD CMOS sensor, can reach
maximum 1920 x 1080 high resolution and achieve
quality image.
DOUBLE INTERFACE
Support 3G-SDI interface, effective transmission
distance up to 150 meters (under 1080p30).
SDI, Network can output at the same time.
ULTRA-HIGH FRAME RATE
The output frame rate up to 60fps in 1080P.
AAC AUDIO ENCODING
Support AAC audio encoding, better sound quality
and smaller bandwidth.
LOW-LIGHT
High SNR of CMOS sensor combined with 2D and
3D noise reduction algorithm, effectively reduce the
noise, even under low illumination conditions, picture
can still keep clean and clear.
POE (OPTIONAL)
Support PoE (802.3af), effectively reduce the cost of
engineering and routing.
ICR INFRARED FILTER
ICR lter with auto switch, keep watch over day
and night.
SDK
Support SDK, easy to implement the custom
requirement .
When opened the package, please check and
conrm that all attachments shall be provided:
HD Color Box Camera X1
The user manual X1
Certicate/warranty card X1

VHD-J1600SE
DATASHEET - MANUAL
> CAMERA DESCRIPTION
> OSD MENU OPERATION
Specic function shown in the table below:
4. MENU key
Move MENU key up and down or so, in order to
select the MENU options. Press down for selected.
5. LINE OUT key
6. CF Card
7. LINE IN key
8. Internet port
9. 3G-SDI interface
OPERATING TIPS!
Press “MENU” button and then to electricity and
keep holding down the “MENU” button 8 seconds,
the camera will restore factory Settings.
CAMERA APPEARANCE
1. Lens focal adjustment after xed screw holes.
2. Lens mounting position (only for C / CS lens *).
3. Aperture control interface (only applicable CD
automatic aperture).
4. The installation location hole.
5. Fuselage.
Both sides threaded hole is consistent with the
positioning hole size, installation can be used instead
of each other.
NOTICE!
Use C camera lens, you need to use special
adapter ring.
THE BACK OF THE INTERFACE SPECIFICATIONS
1. DC 12V power interface
2. Power light
3. Six spring terminals:
KEY DESCRIPTION
The camera uses one buttons, around the menu
button, logo (▲▼) up and down, logo (◄►) left and
right; Under normal image press “MENU” key, the
screen displays the main menu, toggle (▲▼), from
top to bottom cycle options menu item and press
select menu options, use a scroll arrow or highlight
the selected item, press menu button to highlight the
menu item; Each menu page has a “Return” option,
to Return to the superior menu or exit
the menu.
MENU (Main Menu)
Directly press “MENU” button to enter the
main menu.
MENU
► Exposure
► Color
► Image
► Noise Reduction
► Setting
► Information
► Restore Default
► Exit

VHD-J1600SE
DATASHEET - MANUAL
OPERATING TIPS
Press “MENU” button and then to electricity
and keep holding down the “MENU” button 8
seconds, the camera will restore factory Settings.
OSD MENU OPERATION
Toggle the buttons up and down (▲▼) Choose a
menu item, press MENU to enter sub MENU.
Choose [Exit] press MENU button to exit menu.
EXPOSURE
OPERATING TIPS
Mode: Set the camera exposure mode.
Optional items: Full Auto, Bright, Shutter Priority.
Shutter: Set the Shutter values, only when
the Mode for the Shutter Priority Mode and
Manual Mode effective, Optional items:
1/10000s,1/6000s,1/4000s,1/3000s,1/2000s,1/1
500s,1/1000s,1/725s,1/500s,1/350s,1/250s,1/20
0s,1/125s,1/100s,1/90s,1/60s,1/30s.
GainLimit: Set the Gain value, Optional items:
0~15.
Bright: Set the brightness values, only when
the effective Mode for Bright Mode, Optional
items: 0~17.
ExpCompMode: Set the exposure compensation
mode, can be installed: On, Off.
ExpComp: Set the exposure compensation value,
only when ExpCompMode item to On effective,
Optional items: -7~7.
Backlight: Set the backlight compensation,
Optional items: On, Off.
DRC Strength: Set up digital wide dynamic
strength, can set up different levels of wide
dynamic effect, Optional items: 0~8.
Anti Flicker: Set the ashing function,
Optional items: 50Hz, 60Hz, Off.
Style: Optional items: Manual, DC.
Return: get back
COLOR
OPERATING TIPS
Luminance: Brightness adjustment.
Optional items: 0~14.
Contrast: Contrast adjustment.
Optional items: 0~14.
Sharpness: Sharpness adjustment.
Optional items: Auto, 0~15.
Flip-H: Image ipped horizontally.
Optional items: On, Off.
Flip-V: Image Flip Vertical.
Optional items: On, Off.
Gamma: Gamma adjustOptional items:
Default, 0.45, 0.5, 0.56, 0.63.
Style: Optional items: Norma, Clarity, Bright, Soft.
LDC: Optional items: Off, 1-10.
Return: get back.
NOISE REDUCTION
OPERATING TIPS
2D NR: 2D noise reduction,
Optional items: 1 ~ 5, Close, Auto.
3D NR: 3D noise reduction,
Optional items: 1 ~ 8, Close.
Return: get back.
SETTING
OPERATING TIPS
Language: Language Settings.
Optional items: English, Chinese.
Protocol: Communication protocol Settings.
Optional items: VISCA, PELCO-D,PELCO-P.
VISCA Address: Address of the Visca.
Settings, Optional items: 0~7.
P-D Address: P-D address settings, valid in PELCO-D.
Optional items: 0~254.
P-P Address: P-P address settings, valid in PELCO-P.
Optional items: 0~31.
► Mode Full Auto
► ExpCompMod On
► ExpComp -1
► Gain Limit 3
► Backlight Off
► DRC Strength 3
► Anti Flicker 50Hz
► Style Manual Return
► 2D NR 3
► 3D NR 3
► RETURN
► LANGUAGE ENGLISH
► PROTOCOL VISCA
► VISCA ADDRESS 1
► BAUDRATE 9600
► VIDEO FORMAT 1080P30
► EPTZ OFF
► RETURN
► WB Mode Auto
► AWB sens Low
► RG Tuning 2
► BG Tuning -1
► Saturation 100%
► Hue 7
► Return

VHD-J1600SE
DATASHEET - MANUAL
Baudrate: Camera baud rate settings,
Optional items: 38400,19200,9600,4800,2400.
Video Format: Camera video format settings,
Optional items: 1080I50, 1080I60,1080P60,
1080P50, 1080P30, 1080P25, 720P60, 720P50.
EPTZ: Optional items: Off. Return: get back.
INFORMATION
Picture 1.1 connect by enternet cable.
Picture 1.2 Connect by router /interchanger.
IP camera default IP address”192.168.100.
88”, Unknow camera IP, view as below:
Method 1: connect camera to TV,press [menu] of the
behind camera, select “Information”, the camera IP
will be show on screen.
Method 2: connect camera to PC with ethernet cable,
use “upgrade_En.exe” to search for IP address.
Change IP address, 2 methods as below:
Method 1: On web control page, nd “Network”
--->Change IP
---->Click “Apply”
----> Restart camera.
► VERION 7.1.79
► DATA 2016-01-15
► IP 192.168.100.99
► GATEWAY 192.168.100.1
► NETMASK 255.255.255.0
► RETURN
► YES
► NO
► RETURN
RESTORE FACTORY SETTINGS
OPERATING TIPS
YES: verify, press MENU to restore factory
Settings.
NO: cancel, press MENU to back to menu.
RETURN: get back.
> EQUIPMENT SETUP AND
INTERNET CONNECTION
> SETUP IP ADDRESS
1. OPERATING ENVIRONMENT
Operating System: Windows 2000/2003
/XP/vista/7/8.
Network Protocol: TCP/IP.
Client PC: P4/128MRAM/40GHD support scaled
graphics card, support DirectX8.0 or more
advanced version.
2. EQUIPMENT INSTALLATION
1) Connect internet camera to your internet or
to your PC directly via internet cable.
2) Turn on DC12V power.
3) The orange light of internet port lit on, green
light ashing, and the physical connection nished.
3 INTERNET CONNECTION
Connection ways between internet camera and
computer, as picture 1.1 and picture 1.2 shown:
> IP CAMERA VISITED/
CONTROLLED BY LAN

Input http://192.168.100 to IE ( better with IE web
browser, others will cause little latency), a login
window pop up, input login name: admin, password:
admin, shown as below:
After login shown as below:
VHD-J1600SE
DATASHEET - MANUAL
Method 2: Open “upgrade_En.exe”, change
IP and click “Set”.
NOTE!
IP camera default IP address”192.168.100.
88”, user “admin”, password “admin”.
After modied, IP Camera be restart.
NOTE!
If user rst time use this camera by internet (only
for new user), must install a player software (VLC).
Please go to VLC webside: http://www.videolan.org/
vlc,download and Install VLC (player software).
After installation, login again, will show as above:
> VISIT/ACCESS IP CAMERA
> IP CAMERA ACCESSED/
CONTROLLED BY WAN (internet)
> SETUP IPC ACCESSED/
CONTROLLED BY DYNAMIC DNS
2 DYNAMIC DNS AVAILABLE:
Dyndns.org, 3322.org.
ROUTER PORT MAPPING:
Take TP-LINK router for example, enter Router Home
Page (interface page), select “Transit control”- “Transit
rule”--”Virtual server”-- “Virtual service”, add a new
port number in “Outside Port”, add a new port
number in “inside port”, put camera IP address to “IP
address”, then select “Apply” and “Add”, shown as
below: (sorry, we do not have English Version TP-Link
here, so put the Chinese Version picture for reference,
the position is the same).
Set domain name to camera, setup the parameter,
then dynamic DNS can access camera.
Access link: http://hostname: port number For
example, setup host computer name: youdomain.
f3322.org, camera port number: 554,Access link
should be: http://youdomain.3322.org:554.
> DYNAMIC DNS VISIT CAMERA

VHD-J1600SE
DATASHEET - MANUAL
NOTE!
If camera port default as 80, then unnecessary to
input port number, use host name can access
camera directly.
NOTE!
RTSP port number default value is 554.
Open VLC media player, click
“Media”->”Open Network Steam”, or click
“Ctrl+N”; as below:
Input URL address:
rtsp://ip: port number/1 (Main stream);
rtsp://ip: port number/2 (Sub stream).
> VLC STREAM MEDIA PLAYER
MONITORING VISIT VLC MEDIA
SERVER PROCEDURE
> IP CAMERA PARAMETER SETUP
> MEDIA
HOMEPAGE INTRODUCTION
MENU
All pages include 2 menu bars:
Real time monitoring: displaying video image
Parameter setup: with function buttons.
VIDEO VIEWING WINDOW
Video viewing window must be same as video
resolution, the bigger the resolution is, the bigger
the playing area is.
Double click viewing window, will show full-screen,
double click again, will return to initialized size.
Status bar in viewing window shown as below:
1) Video playback pause button: control real-time
video pause, stop the last picture, click recoverable
video again.
2) Audio control buttons: can set slient mode.
3) Full screen switch button.
LANGUAGE SELECTION
CHINESE/ENGLISH/RUSSIAN

VHD-J1600SE
DATASHEET - MANUAL
1) VIDEO FORMAT
Support 50HZ and 60HZ, and OSD three formats.
2) ENCODE PROTOCOL
Support H.264 and H.265 and MJPEG three formats.
3) ENCODE LEVEL
Support baseline, mainprole, highprole three
formats.
4) RESOLUTION
Main bit ow support 1920x1080,1280x720,
1024x576 minor bit ow support 720x480, 720x576,
320x240, the bigger resolution is, the clearer the
image will be, more network bandwidth will be taken.
5) BIT RATE
User can assign bit ow/stream, normally speaking,
the bigger bit ow is, the clearer the image will
be. The bit allocation must combine with network
bandwidth, when the network.
8) BIT RATE CONTROL
Code stream control way:
Constant bit rate: video coder will be coding
according to preset speed.
Variable bit rate: video coder will adjust the
speed based on preset speed to gain the best
image quality.
9) FLUCTUATE LEVEL
Restrain the uctuation magnitude of variable rate,
grade 1~6 bandwidth is too narrow and the allocated
bit ow is too big, will cause video signal ow not to
be transmitted normally, the video effect
will be worse.
6) FRAME RATE
User can specify the size of the frame rate, generally,
the frame rate greater, the image more smooth;
Frame rate is smaller, the more sense of beating.
7) I KEY FRAME INTERVAL
Set interval between 2 I frame, the bigger interval is,
the response will be lower from viewing window.
8) BIT RATE CONTROL
Code stream control way: constant bit rate video
coder will be coding according to preset speed.
Variable bit rate video coder will adjust the speed
based on preset speed to gain the best image quality.
9) FLUCTUATE LEVEL
Restrain the uctuation magnitude of variable rate,
grade 1~6.
> SYSTEM SETTING, PLEASE CLICK
“SYSTEM”
1) WORK MODE
Work Mode RTSP.
2) REBOOT
Click the “Reboot” button, system restart.
3) USER AND PASSWORD.
The user can modify the password (letters
and Numbers only).
4) APPLY / CANCEL
Modify password and click the “apply” button to
the login page, press “cancel” button to cancel
password change.