VIA Technologies Pixetto User manual

Overview
Grove connector
Packing List
•VIA Pixetto vision sensor
•Micro USB 2.0 cable
•Grove cable
6. Wait until all three LEDs are lit. This indicates that the device is
readytouse. Remember to remove the camera lens cover.
Camera lens Reset button
Microphone
Micro USB 2.0 port
Wi-Fi antenna
Micro SD card slot
•Quick Guide
Connecting Method
1. Go to www.pixetto.ai website to download the
pixetto-studio-1.0.0-windows.exe.
2. Doubleclickonthepixetto-studio-1.0.0-windows.exetoinstall.
3. After the installation is completed, the following shortcuts will
be created on your desktop.
7. Open the VIA Pixetto Utility tool to view thelive capture video
from the VIA Pixetto vision sensor.
Updating Firmware
1. Connect the VIA Pixetto vision sensor to your PC/laptop.
2. Open the VIA Pixetto Utility tools. Click Help from the menu
items then select “Device Update” to update thefirmware.
Quick Guide
Specifications
4. Connect the Micro USB cable to the Micro USB 2.0 port on the
VIA Pixetto vision sensor.
5. Connect the VIA Pixetto vision sensor to the USB 2.0 or
USB 3.0 port on your personal computer/laptop.
3. Wait until the upgrade is completed. CAUTION: Do not unplug
the cable duringthe update process. Removing the cable may
cause damage to the VIA Pixetto vision sensor.
Safety Precautions
•We recommend adult supervision for users under the age of 18
years old.
•Avoid contact with moist objects, or moist or damp
environments.
•The device is not water proof. Please avoid contact with water
at all times.
•Do not expose the device to extreme high or low
temperatures.
•To avoid damage, do not touch the surface of
the device while in use
For full instructions, please visit the
official website www.pixetto.ai
Processor ARM Cortex-A7 900MHz
System Memory 64MB DDR SDRAM
Storage 128MB SPI Flash memory
Camera Sensor GalaxyCore GC2053 CMOS image sensor
Camera Resolution 1920 x 1080
Camera Lens 130° Field-of-View
Onboard I/O 3 LEDs (for power, Wi-Fi and active status) 1
Reset button
1 Microphone
1 Grove connector
1 Micro USB 2.0 port
1 Micro SD card slot 1
Wi-Fi antenna
Power Supply 5V/500mA Micro USB 2.0 port
5V/300mA and 3.3V/500mA Grove connector
Operating System Linux
Operating Temp. 0°C ~ 45°C
Size 38mm x 38mm (1.5” x 1.5”)

FCC Caution
§ 15.19 Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2)this device must accept anyinterference
received, including interference that may cause undesiredoperation.
§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant topart 15 of theFCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and usedin accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference toradio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged totry to correct theinterference byone or
more of the following measures:
-Reorient or relocate the receivingantenna.
-Increase the separation betweenthe equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that
To whichthe receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
The modular can be installed or integrated in mobile or Mobile
devices.
This modular complies withFCC RF radiation exposure limits
set forth for an uncontrolled environment. This transmitter
must not be co-located or operatingin conjunction with any
other antennaor transmitter.
This equipment should be installed and operated withminimum
distance 20cm between the radiator & your body
If the FCC identification number is not visible when the module
is installed inside another device, then the outside of the device
into which the module is installed must also display a label
referring tothe enclosed module. This exterior label can use
wording such as the following:
Contains FCC ID: NCIVTS8787X
The requirement for KDB 996369 D03:
List of applicable FCC rules
FCC Part 15. 247.
No. Description
1 Peak Output Power
2 6dB and 99% Occupied Bandwidth
3 Conducted Band Edges and Spurious
Emission
4 Power spectral density (PSD)
5 Conducted Emission
6 Radiated Band Edges and Spurious Emission