Victa RM100 User manual

Operator's
Manual
Victa Robot
Mower RM100
WARNING! Read this manual before operating your Victa Autonomous Mower.

Safety Marking and Symbols
Read this manual carefully prior to assembling and operating the Autonomous
Mower. It is dangerous to operate this product without being familiar with these
instructions. Keep this manual in a safe place and have it ready for future reference.
General notes on safety
This appliance can cause serious injury if it is not properly used. Please read these
operating instructions carefully and familiarise yourself with all the control elements before
operating this appliance. Keep these operating instructions in a readily accessible place
so that this information is always at your disposal.
Please note that despite all precautions to integrate safety precautions into the
construction, the safety appliances and supplemental safety mechanisms, a residual risk
remains when using this appliance.
Warning! Warning! Electric shock.
Keep bystanders well
away from the appliance.
Always stop the appliance and
wait for the cutting blades to stop
before carrying out any inspection
and/or maintenance.
Do not ride on the appliance.
Do not stand or sit on the
appliance or load objects onto
it or the charging station.
Read the directions and
remove plug from the mains
before carrying out any
maintenance work.
Cleaning with water
systems can cause
damage
The robot is protected by an
access PIN code and an
anti-theft system.
Never place hands under or near
the appliance when it is
operating
Never place feet under
or near the appliance
when it is operating
Be careful of objects being
thrown out!
Read the directions for use
before operating the appliance.
2
IMPORTANT NOTES

Take batteries to an old battery
collection point where they will
be recycled in an environmentally
friendly manner.
Do not throw into water.
Do not throw on the fire
Warning Symbols on the battery pack
Do not subject the battery to strong
sunlight over long periods and do not
leave it in high temperatures.(max.45 C).
3
IMPORTANT NOTES
Batteries contain Li-Ion and
should not be disposed with
general household waste. Contact
your local authority for disposal
advice.
Double insulation
Pole orientation
SMPS (Switch mode power
supply unit) incorporating a short-
circuit-proof safety isolating
switching power supply
SMPS(Switch mode power
supply unit)
The Power Supply is for
indoor use only.
Return any discarded batteries to your
local dealer, collector or recycle point.
It is not permitted to dispose of this
product with normal household waste.
Please recycle where facilities exist.
Check with your local authority or
retailer for recycling advice.
Guaranteed sound power level
value is 67dB.
67

Table of Contents
Important Notes 2
Introduction
Safety Marking & Symbols
Features & Definitions 5
Features
Technical Data
Safety & Handling 7
Safety Instructions
Operation Principles 12
Autonomous Mower basic operating principles
Locating the charging station
Recognising the boundary wire
Starting and stopping while mowing
Autonomous Mower mowing limitations
Autonomous Mower cutting information
Installation Procedures 16
Installation Guide
Uneven lawn surfaces
Flowerbeds
General Dos and Don’ts
Marking out the Autonomous Mower's
working area
Pegging out the boundary wire
Operating Instructions 26
Setting the mowing height
Starting and stopping the mower
Messages on the display during operation
Returning to the charging station
Programming the mower
Control Panel
Display
Using the control menu
Maintenance & Care 39
Storage
Cleaning and Maintenance
Reversing or replacing the blades
Replacing the battery
Troubleshooting 42
Charging station
Display messages and common problems
Error codes
4
1. Autonomous
Mower x 1
5. Docking
station x 1 9. Rear wheel 13. Switching power
supply x 1
17. Boundary wire
connector x 3
2. STOP button 6. Blade x 3 10. Carrying
handle
14. Extension
cord x 1
18. Boundary wire
x 1 (120m)
3. Display and
keypad
7. Blade disc 11. Main power
switch
15. Fixing peg x 150 19. Spare blade
& Bolt x 3
4a. Charging
contacts
(Autonomous
Mower)
4b. Charging
contacts
(Docking
station)
8. Front wheel 12. Control panel 16. Measurement
ruler (on the
color box) x 2
20. Operator's
Manuals

5
4a
12
15
18
16
17
13
14
19
4b
5
DEFINITIONS
1
2
3
8
9
67
11
10
20
Original
instrcution
Operator's
Manual
Warranty
Warranty
Quick Start
Guide
1. Autonomous
Mower x 1
5. Docking
station x 1 9. Rear wheel 13. Switching power
supply x 1
17. Boundary wire
connector x 3
2. STOP button 6. Blade x 3 10. Carrying
handle
14. Extension
cord x 1
18. Boundary wire
x 1 (120m)
3. Display and
keypad
7. Blade disc 11. Main power
switch
15. Fixing peg x 150 19. Spare blade
& Bolt x 3
4a. Charging
contacts
(Autonomous
Mower)
4b . Charging
contacts
(Docking
station)
8. Front wheel 12. Control panel 16. Measurement
ruler (on the
color box) x 2
20. Documents:
Operator's Manual
Warranty Card
Quick Start Guide
Features
FEATURES

Technical Data
Functional description
This Autonomous Mower is an autonomous robot used to cut lawn grass. It will remain
within an area designated by a boundary wire, start work following a programmed schedule
and return to its charging station as needed. The three sharp blades ensure clean cuts with
minimal damage to the plant, leaving behind tiny snippets as natural fertilizer.
Model 2691783
Model Name Victa Robot Mower RM100
Max cutting area 600 m²
Battery 80086647-INR18650-20R
Lithium-Ion battery, 28V/2.0Ah, 56Wh
Switching power supply 80086689 Input 100-240V AC,
50/60 Hz Output 32 V DC, 1.5A
Typical mow time on one charge 60 min
Rated voltage 28 V DC
Rated power 50 W
No load cutting speed 3500 min
Cutting width 18 cm
Blade model / part number 80086674
Cutting height adjustment Stepless
Cutting height, min-max 20 mm-60 mm
Number of blades Three (Pivoting)
Charging time 60 min
Recommended time per day
300 m² 4 hours
600 m² 6 hours
Degree of protection:
Autonomous Mower IPX4
Docking Station IPX4
Autonomous Mower weight 8.5 Kg
Charging Station weight 2 Kg
Autonomous Mower size, L x W x H 570 X 390 X 260 mm
Package size, L x B x H 720 X 470 X 330 mm
Gross weight 16.5 kg
Measured sound power level
Measured sound pressure 66.4 dB(A) , K=3.0 dB(A)
Guaranteed sound power level L = 67 dB(A)
-1
6
FEATURES DEFINITIONS

Main Power
isolation switch
Safety InstructionsSafety Instructions
Safety instructions for Autonomous Mowers
Do not store anything heavy on the top of the Autonomous Mower or charging station both
during storage and when use.
Never use the appliance if the main power switch (11) is damaged or does not work
properly. Never modify the main power switch. Set the main power switch to OFF for
storage or when the appliance is not in use. Use the original packaging when transporting
the Autonomous Mower, especially for long distances.
If you need to carry the Autonomous Mower from or within the working area, first press the
STOP button (2) to stop the appliance.
Ensure that the main power switch (11) is switched OFF before you lift up your Autonomous
Mower.
2
11
7

8
Close the top cover and carry the Autonomous Mower by the carrying handle (10) at the rear
under the mower, keeping the blade disc away from your body as shown.
Note: The carrying handle (10) includes two safety switches. Lifting the appliance by the
carrying handle will trigger the switches, deactivating the Autonomous Mower.
Lightning Protection
In order to prevent lightning damage to the appliance, do not place the charging station under
tall trees.
Do not use the Autonomous Mower during lightning or thunder storms. In case of damage to
the electronic circuitry, unplug the charging station and - if possible - disconnect the boundary
wire.

9
Operating the appliance:
WARNING! This appliance can cause serious injuries. Follow instructions
below to reduce risk of accident and injury.
IMPORTANT! READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE.
• Read the instructions carefully and make sure you understand them fully. Be familiar with the
controls and the proper use of the appliance.
• Never allow children, persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge or people unfamiliar with these instructions use the appliance.
• Local regulations may restrict the age of the operator. Children should be supervised to ensure
that they do not play with the appliance.
• The operator or user is responsible for accidents or hazards occurring to other people or their
property.
• Ensure the correct installation of the perimeter boundary system as instructed.
• Periodically inspect the area where the appliance is to be used and remove all stones, sticks,
wires, and other debris which could cause damage to the appliance or be unsafe.
• Periodically visually inspect to see that the blades, blade bolts and cutter assembly are not
worn or damaged. Replace worn or damaged blades and bolts in sets to preserve balance.
• Never leave the appliance to operate unattended, especially while other people such as
children and pets are in the area.
• Never use the appliance to level out uneven patches.
• If the blades no longer cut correctly or if the motor is overloaded, check all the parts of your
equipment and replace the worn parts. If a more extensive repair is required, contact the
customer service centre.
Use:
• Never operate the appliance with defective guards or without safety appliances, for example
deflectors in place.
• Do not put hands or feet near or under rotating parts.
• Never pick up or carry the appliance while the motor is running.
• Press STOP button
• Turn OFF / Power OFF the appliance
– before clearing any blockages.
– before checking, cleaning or maintaining the appliance.
• Start Autonomous Mower according to the instructions. When the main power switch (11) is in
the ON position, make sure you keep your hands and feet away from the rotating blades.
• Never lift the Autonomous Mower or carry it around when the main switch is in the ON
position.
• Do not let persons use the mower who do not know how it works or behaves.
• Do not put anything on top of the Autonomous Mower or its charging station.
• Do not use the Autonomous Mower with defective blade discs, body, defective blades,
screws, nuts etc.
• Avoid operating the appliance in wet grass. Doing so can cause additional wear and tear and
will increase the amount of cleaning required.
Preparation:

10
Work interruptions:
• After the appliance has been turned off, the cutting cylinder will continue to rotate
for a few seconds. Keep hands and feet well away.
• Only remove blockages when the appliance is standing completely still.
• Switch off the power when the appliance is transported, lifted or tilted.
• Never leave the appliance unattended. Children should be supervised to ensure that
they do not play with the appliance.
CAUTION!
The following below outlines measures to avoid damage and harm to
both the Autonomous Mower and people using it.
Taking care of your appliance:
• Switch off the power when the appliance is to be carried across uneven surfaces,
for example steps.
• Inspect the appliance before each use. Never operate the appliance if safety
appliances (e.g. impact protector, parts of the cutting facility or bolts) are missing,
worn out or damaged. Check the power cable. To avoid imbalance, all tools and
bolts must be changed as complete sets.
• Only use spare parts and accessories that have been supplied or recommended
by the manufacturer. The use of alien parts results in the immediate loss of all
guarantee claims.
• Ensure that all nuts, bolts and screws are firmly tightened and that the appliance is
in a safe working condition.
• Never try to repair the appliance yourself, unless you have been trained accordingly.
All work that has not been listed in these instructions must only be carried out by
authorised servicing agencies.
• Treat the appliance with the greatest care. Always keep the tool clean. Follow the
maintenance instructions.
• Never overload the appliance. Always work within the specified capacity range. Do
not use low-power appliances for heavy-duty work. Do not operate the appliance for
purposes for which it is not intended.
Electrical safety:
CAUTION!
The following states how to avoid accidents and injuries due to electric
shock:
• Before each use, carry out a visual inspection of the power and extension cord for
any signs of damage or ageing. Damaged mains power cables increase the risk of
electric shock.
• Connect the appliance to a power socket with a residual-current circuit breaker that
has a rated current of no more than 30 mA.

11
• Always keep the extension cable well away from the cutting tools. Once the
power cable become damaged during work, instantly disconnect the power cable
from the mains. DO NOT TOUCH THE POWER CABLE BEFORE IT HAS BEEN
DISCONNECTED FROM THE MAINS! Risk of electric shock.
• The supply cord cannot be replaced. If the cord is damaged the appliance should
be scrapped.
• Keep extension cable away from blades and other moving parts. They may damage
the cable and result in contact with live parts.
• Check that the mains voltage is the same as indicated on the rating plate.
Maintenance and storage
• Keep all nuts, bolts and screws tight to be sure the appliance is in a safe working
condition.
• Replace worn or damaged parts for safety.
• Ensure that only the recommended replacement cutting blades are fitted.
• Ensure that batteries are charged using the charger supplied or recommended by
the manufacturer. Incorrect use may result in electric shock, overheating or leakage
of corrosive liquid from the battery.
• Servicing of the appliance should be carried out according to manufacturer's
instructions.
• In the event of leakage of electrolyte, flush with water / neutralising agent, seek
medical help if it comes into contact with the eyes.
• Store the appliance with battery pack fully charged at room temperature (around
20ºC).
• Every deep discharge cycle decreases the capacity of battery pack. To prolong
battery life, it is recommended to charge the battery every 6 months over extended
periods of time without use.
Transport
The original packaging should be used when transporting the Autonomous Mower over
long distances. To safely move from or within the working areas:
• Press the STOP button to stop the mower.
• Move the main switch button to the OFF position if you intended to carry the mower.
• Carry the Autonomous Mower using the handle below at the rear. Carry the mower
with the blade disc away from the body.

12
OPERATION PRINCIPLES
The Autonomous Mower chooses its working direction randomly. It will mow your
garden completely without leaving behind any uncut part within the area restricted by
the chosen boundary.
• You define the work area by installing the supplied boundary wire. Once the
Autonomous Mower detects the boundary wire, it will stop, move backwards
and continue mowing in a different direction. It is important to ensure that the
boundary is complete. Any objects you wish to protect within the boundary,
such as a garden pond, trees, garden furniture or flower beds can also be
protected by the boundary wire. The boundary wire must form one complete
loop. If the Autonomous Mower encounters an obstacle, such as a person,
tree, pet or other general garden obstacles, it will stop, move backwards and
continue mowing in a different direction.
• If you need a narrow corridor to connect two patches of lawn within the
boundary, the corridor should be at least 2 metres wide and max. 8 m long.
max. 8 m
min. 2 m
Autonomous Mower Basic operating principles
Chaging Station
Work Area
Boundary Wire
Autonomous Mower

13
OPERATION PRINCIPLES
Note: If your Autonomous Mower loses ground contact while hitting an obstacle, the blade
disc will stop immediately to avoid any potential damage.
• When the battery is running low, the Autonomous Mower will automatically return
to the charging station. It will approach the closest boundary wire and follow it
anticlockwise (without cutting) back to the charging station. When fully charged, the
Autonomous Mower will automatically resume the interrupted working cycle. The
launch direction from the charging station - clockwise - is hard-wired into the design
and is impossible to change.
• Note that before stopping and changing the direction, the Autonomous Mower will
overrun the boundary wire by 10 to 40 cm. Please keep this in mind when planning
the boundary wire installation.
10-40 cm
Locating the charging station
Recognising the boundary wire

OPERATION PRINCIPLES
14
• The Autonomous Mower is set to work 7 days a week. You can adjust the daily
working time to match your garden.
• In case a neighbour is using the same Autonomous Mower, you need to keep a
0.5 m distance between your and your neighbour's boundary wires. Otherwise,
the two appliances might interfere with each other. Additionally, keep your
charging station more than 10 m away from your neighbour's boundary wires.
Last but not least, ensure that the adjacent boundary wires use different signals.
Please refer to section "Signal setting" in order to select signal S1 or S2 for your
installation.
> 0,5 m
> 10 m
> 10 m
S1 S2
Own land Neighbour
Autonomous Mower mowing limitations
• If you want to stop the Autonomous Mower at any time during cutting, please
press the STOP button (2). Pressing the STOP button will also open the top
cover, providing access to the control interface. After pressing the START
button, The Autonomous Mower will not start working again until you have
closed the top cover.
Starting and stopping while mowing

15
OPERATION PRINCIPLES
Below is a table showing the signal distance for your Autonomous Mower. Use this
information as your guide when designing the boundary layout.
Model Max eld Max. distance to wire
Victa Robot
Mower RM100 600m² 12.5m
• The Autonomous Mower has a cutting height setting between 20 mm to 60 mm. If the
grass height exceeds 60 mm, cut it to 60 mm or below before using the Autonomous
Mower. Otherwise the load on the unit will be too large and the cutting efciency will
suffer, we recommend using an ordinary lawn mower or trimmer. Once the installation
is complete, adjust the cutting height to the desired setting. Always start in a high
cutting position and work your way down to the cutting height you want. Before
adjusting the cutting height, always press the STOP button (2) to interrupt the cutting.
Then turn the large dial to adjust the cutting height.
Note: Only adjust the cutting height while the Autonomous Mower is switched off.
The Autonomous Mower cutting efciency relies on sharp blades, so please keep them in
good condition.
Autonomous Mower cutting information

16
Cutting limitations
Installation Guide
Trees
This chapter explains how to install the Autonomous Mower. Please read this completely
before you start the installation.
Introduction
We recommend creating a draft of your lawn, including all obstacles and how these should
be protected. This makes it easier to find a good position for the charging station and how
to correctly place the boundary wire around your garden perimeter protecting bushes,
flower beds etc. You will also need some tools, like a hammer and wire cutters, pliers or
scissors.
The Autonomous Mower is equipped with
collision sensors. These will detect any rigid
and fixed obstacles higher than 100mm, such
as walls, fences and garden furniture.
When triggered, the Autonomous Mower will
stop, reverse backwards and then continue
mowing in a different direction. Still, protecting
the obstacles running the boundary wire
accordingly is the recommended long-term
solution.
< 400 mm
> 100 mm
INSTALLATION PROCEDURES
The Autonomous Mower treats trees as
common obstacles, but if some roots of the
tree are exposed in your garden and lower
than 100mm, this area should be proteched
in order to prevent tree root, cutting blades or
rear wheels profile damage.

17
Stones
Slopes
Paths, Driveways and Roads
We recommend clearing the lawn
of small (less than 100 mm high)
rocks and stones and any stones
with a round or sloped edge. The
Autonomous Mower might try
and climb such rocks instead of
recognising them as a barrier.
An Autonomous Mower getting
stuck on such a stone requires
user intervention to restart mowing.
Contact with stones can result in
damage to the blades.
The Autonomous Mower can
navigate slopes up to a maximum
of 40% incline or decline.
The boundary wire should never
run perpendicular to a gradient of
more than 10°. Likewise, please
allow a corridor of at least 2m
between a 10° or steeper slope
and the boundary wire. Otherwise,
the faster downhill speed may
cause the Autonomous Mower
to overshoot the boundary wire,
especially on wet and slippery
ground.
If an elevated driveway crosses
your lawn, better keep it outside
the boundary wire.
Please allow a safety distance
of 40 cm between driveway and
boundary wire.
Slope should not be steeper
than 50 % (27˚).
min.
2
m
Slope should not b e
Slope should not be
steeper than 10˚
Boundary wire
> 40 cm
boundary wire
INSTALLATION PROCEDURES
40 % (22°).

18
If the driveway and lawn are at
the same level, feel free to use the
boundary wire to create a corridor.
This allows your Autonomous
Mower to cross the driveway and
reach the opposite lawn.
Use the boundary wire to exclude
any flowerbeds from the cutting
area.
There are two options for the two
lengths of boundary wire running
between the flowerbed and the
outer boundary:
1) Keep the distance between the
parallel wires above 10 cm. This
way, the Autonomous Mower will
recognise the boundary wire as an
ordinary obstacle. When cutting, it
will "bounce" off it as usual. When
following the boundary wire back
to the charging station, it will take
the detour around the flower bed.
boundary
boundary
Uneven lawn surfaces
Flowerbeds
> 10 cm
INSTALLATION PROCEDURES
Uneven lawn areas may cause the
blades to touch the ground, and/
or allow Autonomous Mower to
get stuck.
We recommend leveling the lawn
before using your Autonomous
Mower or excluding uneven areas
with the boundary wire.

19
CHOKE
2) Alternatively, keep the distance
between the two parallel wires
below 5 mm. Do not cross the
wires - see below.
This way, the Autonomous Mower
will not recognise the wires and
travel across them unhindered. This
option requires placing an obstacle
on the boundary wire around the
flowerbed. Place the obstacle, e.g
a large rock or pole, near position a
indicated on the below illustration.
The obstacle must be surrounded
by a flat area of about 1 m x 1 m,
without any slopes. This obstacle
will allow the appliance to exit the
circle.
< 5 mm
> 10 cm
General Dos and Don’ts
While the Autonomous Mower is protected against rain and spray water, being submerged
is likely to cause severe damage to the electronic parts. Therefore, it is imperative to
exclude any pools from the cutting area. For added safety, we recommend placing a fence
around the pool with a height greater than 10cm.
Keep in mind that flowers, bushes
and surrounding shrubbery will
change in size over a season.
please keep sufficient space
between boundary wire and other
plants to avoid interference year-
round.
INSTALLATION PROCEDURES

20
You have now understood the basic
principles of how the Autonomous
Mower works. The next step is to
mark out the working area with
boundary wire by referring to your
garden plan.
Starting from the charging station,
the boundary wire must be one
continuous loop without any breaks
or crossings. Connecting the end
to the charging stations second
connector will complete the circuit.
Where appropriate, use the included
ruler to check the 40 cm required
distance.
Firstly, locate the best position for
your charging station. Be aware that
it needs a permanent connection to
the mains, so take into account the
location of the nearest power outlet.
The included supply cord has a
length of 9m. The charging station (5)
must be placed on a flat surface, at
ground level.
Marking out the Autonomous Mower's working area
Never cross the wires!
Max length
of the
corridor is
8 m
Minimum width of
the corridor is 2 m
If you have created a boundary corridor inside your working area, the corridor should be
at least 2 m wide and a max length of 8 m. If a corridor is too narrow or too long, the
Autonomous Mower might not be able to navigate it from one end to the other.
INSTALLATION PROCEDURES