Victory Motorcycles 2005-2006 Hammer User manual

31
2005-2006 HAMMER TM
2006 VEGAS JACKPOT TM
& NESS SIGNATURE SERIES VEGAS JACKPOT
SERVICE MANUAL
2005-2006 HAMMERTM/ 2006 VEGAS JACKPOTTM SERVICE MANUAL
Printed in USA
9920340
PN 9920340
Cvr_9920340 2/1/06 3:53 PM Page 1

2005-2006 Hammert
2006 Vegas Jackpott
2006 Ness Signature Series Vegas Jackpott
SERVICE MANUAL
Part Number 9920340
Foreword
This manual is designed primarily for use by Victory service technicians in a properly equipped shop and should be kept
available for reference in the shop area. All references to left (LH) and right (RH) side of the motorcycle are from the
operator’s perspective when seated in a normal riding position.
Some procedures outlined in this manual require a sound knowledge of mechanical theory, tool use, and shop procedures
in order to perform the work safely and correctly. Read the text and be familiar with the service procedures before starting
the work. Certain procedures will require the use of special tools. Use only the proper tools as specified. If you have any
doubt as to your ability to perform any of the procedures outlined in this service manual, contact an authorized Victory
dealer for service.
This manual includes procedures for maintenance, component identification and repair, along with service specifications
for the models listed above. Comments or suggestions about this manual may be directed to: Service Publications Dept.
@ Polaris Sales Inc. 2100 Hwy 55 Medina, Minnesota 55340. Victory dealers can also use the on-line feedback forum
located at:www.polarisdealers.com under News, Forms & Links/Service & Warranty/Polaris Manual Feedback link and fill
out the information on the form.
E2005 Polaris Industries. All information contained in this publication is based on the latest product information available at the time of
publication. Due to constant improvements in the design and quality of production components, some minor discrepancies may result
between the actual vehicle and the information presented in this publication. Depictions and /or procedures in this publication are intended
for reference use only. No liability can be accepted for omissions or inaccuracies in this publication. Any reprinting or reuse of the depictions
and/or procedures contained in this publication is expressly prohibited. Printed in U.S.A.

CHARGING SYSTEM
1
2
10
4
5
6
7
9
8
GENERAL
FUEL SYSTEM/FUEL INJECTION
MAINTENANCE
LUBRICATION & COOLING
ENGINE REMOVAL & INSTALLATION
CLUTCH, PRIMARY, & SHIFT
TRANSMISSION & CRANKSHAFT
REAR WHEEL & SUSPENSION
ELECTRIC STARTER
TIRES
ENGINE
ELECTRICAL
3
14
15
16
17
18
19
CYLINDER & PISTON
FRAME/BODY/EXHAUST
CYLINDER HEAD & VALVES
DRIVE LINE
FRONT WHEEL & SUSPENSION
BRAKES
IGNITION SYSTEM & BATTERY
LIGHTING & INSTRUMENTATION
GENERAL & MAINTENANCE
CHASSIS
11
12
13

GENERAL INFORMATION
CHAPTER 1
GENERAL INFORMATION 1
1.1
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3
TRADEMARKS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.3
SERVICE RULES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.3
SAFETY INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4
UNDERSTANDING SAFETY LABELS & INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . .1.4
REFINISHING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5
VICTORY TOUCH-UP AND REFINISHING PAINT / DETAIL & FINISHING KITS . . . . .1.5
PAINTING TERMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.5
PAINT COLORS BY MODEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.6
PAINT COLOR CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.7
VEHICLE INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8
VEHICLE IDENTIFICATION NUMBER (VIN) & MODEL NUMBER DESCRIPTIONS. . .1.8
VIN NUMBER LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.9
MODEL NUMBER LOCATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.9
ENGINE NUMBER LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.9
KEY IDENTIFICATION NUMBER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.9
PUBLICATIONS & TECHNICAL LITERATURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.10
PUBLICATION PART NUMBERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.10
MATERIAL SAFETY DATA SHEET (MSDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.10
BREAK IN PERIOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.11
BREAK-IN PROCEDURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.11
EMISSIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.11
EMISSION CONTROL SYSTEMS / EMISSION SOURCES . . . . . . . . . . . . . . . . . . . . .1.11
EXHAUST EMISSION CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.12
NOISE EMISSION CONTROL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.12
CRANKCASE EMISSION CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.12
EVAPORATIVE EMISSION CONTROL (CALIFORNIA MODELS) . . . . . . . . . . . . . . . .1.12
INSTRUMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.13
SPEEDOMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.13
TACHOMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.13
ODOMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.13
TRIP ODOMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.13
INDICATOR LIGHTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.14
SPECIAL SERVICE TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.15
GENERAL & PRECISION MEASUREMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.15
TUNE UP & MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.15
ELECTRICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.15
ENGINE, CLUTCH, & TRANSMISSION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.16
STEERING & SUSPENSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.16
WHEEL & TIRE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.17
FUEL SYSTEM & FUEL INJECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.17
TOOL ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.17
TRANSPORTING AND SECURING THE MOTORCYCLE. . . . . . . . . . . . . . . . . . . . . 1.18
ROUTING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.19
WIRE HARNESS - LEFT REAR FRAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.19
WIRE HARNESS - RIGHT REAR FRAME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.20
WIRE HARNESS - RIGHT SIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.21
WIRE HARNESS - UNDER SEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.22
REAR FENDER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.23

GENERAL INFORMATION
1.2
WIRE HARNESS CONNECTOR LOCATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.24
TOP VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.24
LEFT SIDE VIEW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.25
RIGHT SIDE VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.26
FUEL TANK VENT AND DRAIN HOSE ROUTING . . . . . . . . . . . . . . . . . . . . . . . . . . 1.27
2005 HAMMER - 49 STATE, CANADA, UK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.27
2006 - ALL EXCEPT CALIFORNIA MODELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.28
CALIFORNIA MODELS (ALL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.29
REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.30
SAE TAP DRILL SIZES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.30
METRIC TAP DRILL SIZES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.30
DECIMAL EQUIVALENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.30
FAHRENHEIT TO CELSIUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.31
MEASUREMENT CONVERSION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.31

GENERAL INFORMATION
1
1.3
GENERAL INFORMATION
TRADEMARKS
Victory acknowledges the following products mentioned in this manual:
FLEXLOC, Registered Trademark of SPS Technologies
Loctite, Registered Trademark of the Loctite Corporation
STA-BIL, Registered Trademark of Gold Eagle
Nyogel, Trademark of Wm. F. Nye Co.
Fluke, Registered Trademark of John Fluke Mfg. Co.
Mity Vac, Registered Trademark of Neward Enterprises, Inc.
Torx, Registered Trademark of Textron
SERVICE RULES
In order to perform service work efficiently and prevent costly errors, technicians should read the text in this manual
and familiarize themselves with the procedures before beginning. Notes, Cautions and Warnings have been included
for clarification of text and safety concerns. Knowledge of mechanical theory, tool use and shop procedures are
necessary to perform some procedures in this manual safely and correctly.
Use only genuine Victory service parts, including fasteners that require replacement if removed. Do NOT substitute
fasteners or hardware.
Cleanliness of parts and tools as well as the work area is of primary importance. Dirt and foreign matter will cause
damage to precision parts. Clean the motorcycle before beginning service. Clean all parts before installing.
If difficulty is encountered in removing or installing a component, look to see if a cause for the difficulty can be found.
If it is necessary to tap the part into place, use a soft face hammer and tap lightly.
Always follow torque specifications as outlined throughout this manual. Incorrect torquing may lead to serious
machine damage or in the case of steering, driveline, and chassis components, can result in loss of control during
operation of the motorcycle, which may result in severe personal injury or death.
If a torquing sequence is indicated for nuts, bolts or screws of a certain component, start all fasteners and hand
tighten. Following the method and sequence indicated, tighten evenly to the specified torque value. When removing
nuts, bolts or screws from a component with several fasteners, loosen them all about 1/4 turn before removing them
to prevent distortion of that component.
Replace all oil seals, sealing washers, gaskets, and O-rings with new ones during assembly. Be sure the mating
surfaces for the gasket are clean and smooth to avoid leaks and maintain specified tolerances.
Some procedures require removal of retaining rings or clips. Removal can weaken and deform these parts, therefore,
they should always be replaced with new parts. When installing new retaining rings and clips, use care not to expand
or compress them beyond what is required for installation.
Victory lubricants and greases have been specially formulated to provide maximum performance and protection when
applied properly. In some applications, warranty coverage may be void if improper lubricants are used.
Parts requiring grease should be cleaned thoroughly and fresh grease applied before reassembly. Deteriorating
grease loses lubricity and may contain abrasive foreign matter.
Always replace locking hardware such as lock nuts or lock washers, fasteners that have pre-applied locking agent, or
any other fasteners as noted in this service manual with genuine Victory hardware from an authorized Victory dealer.
Working with batteries can be hazardous. Review all battery warnings and cautions. See “BATTERY SAFETY” on
page 16.2.

GENERAL INFORMATION
1.4
SAFETY INFORMATION
UNDERSTANDING SAFETY LABELS & INSTRUCTIONS
READ AND BECOME FAMILIAR WITH ALL WARNING AND CAUTION SYSMBOLS AND STATEMENTS
LISTED BELOW AND IN THE TEXT OF THIS MANUAL BEFORE YOU BEGIN WORK.
DANGER, WARNINGS, & CAUTION SYMBOLS
This is the safety alert symbol. When you see this symbol
on your machine or in this manual, be alert to the potential
for personal injury. Your safety is involved!
Indicates a potential hazard which could result in severe
Indicates a potential hazard which may result in minor personal
Indicates a situation that can result in damage to the motorcycle.
The word “NOTE:”in this manual will alert you to key
information or instructions.
Gasoline is extremely flammable and explosive
 Always stop the engine and refuel outdoors or in a
Do not smoke or allow open flames or sparks in or
Do not overfill the tank. Do not fill the tank neck above
If you get gasoline in your eyes or if you swallow
If you spill gasoline on your skin or clothing,
Never start the engine or let it run in an enclosed area.
injury or death.
injury or damage to the motorcycle.
CAUTION
NOTE:
under certain conditions.
well ventilated area.
near the area where refueling is performed or where
gasoline is stored.
the fuel tank insert. Leave air space to allow for fuel
expansion.
gasoline, see your doctor immediately. Never try to
syphon gasoline using mouth suction.
immediately wash it off with soap and water and
change clothing.
Engine exhaust fumes are poisonous and can cause
loss of consciousness or death in a short time.
Improper repairs or service can create The engine and exhaust components on this
The engine exhaust from this product
contains chemicals known to cause cancer,
birth defects or other reproductive harm. unsafe conditions that may cause severe
personal injury or death. product become very hot during operation
and remain so for a period of time after the
engine is stopped.
Never run the engine in an enclosed area Modifications to this motorcycle not approved Brake fluid is poisonous.
KEEP OUT OF REACH OF CHILDREN.
without a properly functioning exhaust gas
evacuation system connected to the product. by Victory may cause loss of performance,
excessive emissions, and make the machine
unsafe for use.
Wear insulated protection for hands and Brake fluid is poisonous. Do not ingest or Battery electrolyte is poisonous. It contains
Brake fluid will damage plastic, painted and rubber parts. Protect
arms or wait until hot components have
cooled sufficiently before working on the
product.
allow brake fluid to contact eyes. Always
wear eye protection when working with
brake fluid.
sulfuric acid. Serious burns can result from
contact with skin, eyes or clothing.
CAUTION
these surfaces whenever the brake system is being serviced.

GENERAL INFORMATION
1
1.5
REFINISHING
VICTORY TOUCH-UP AND REFINISHING PAINT
Service Paint products are available in three different sizes and applications. Some paint colors require up to 3 com-
ponents to create a color. Prices subject to change without notice. Dealer is responsible for freight on paint and paint
products.
.6 ounce bottle: (Order Multiple of 2) For brush touch-up of small nicks.
10 ounce aerosol can: (Order Multiple of 2)
Apply light even coats for best results. Recoat time is from 30-60 minutes or after 4 days of drying to prevent lifting.
Quarts: (Sold as each)
For repaint of properly prepared plastic components or metal substrates.
Paint is a high quality acrylic urethane manufactured by U.S. Paint.
Mix as indicated on back of paint can. Paint can be recoated after paint is tack free or has ”flashed off”.
Paint finish may be wet sanded and buffed after coating has cured.
How to order:
Authorized Victory Dealers only. Place your order via the dealer web site at :
www.polarisdealers.com / News Forms & Links / Pure Polaris
Note: There will be a 25% service fee charged for all returns. Polaris dealer will be responsible for return freight.
VICTORY DETAIL AND FINISH RESTORER KITS
A Detail Kit (polish, wax, and dressing) and a Restore Kit (polish, and swirl / scuff remover) is available from the Vic-
tory parts department for painted surface protection and to remove minor surface imperfections.
Detail Kit: 2872195 (Includes Non-Abrasive Wash, Swirl Remover / Polish, Polywax Final Finish, Vinyl / Rubber
Protector, Applicator and Cloth.
Restore / Polish: 2872192 (12 oz. Aerosol)
PAINTING TERMS
The following terms describe the general operations referred to in the Paint Color Code chart on page 1.7.
E-Coat (Factory Applied): This material is used as a rust protection. It is also used to form a bond between bare
metal and the primer or base coat. Full-hide colors (such as black) do not require primer.
Primer: Primer is necessary when applying some colors such as Flame Yellow, Sonic Blue, Solar Red, etc. The
purpose of a primer coat is to prevent bleed-through or transparency in subsequent color coats.
Base Coat: A color paint layer applied under another color or under the clear topcoat to improve color matching and
consistency.
Top Coat: Outermost layer of paint or clear coat.

GENERAL INFORMATION
1.6
PAINT COLORS BY MODEL
NOTE: Refer to www.polarisdealers.com for more information.
NOTE: The 9th letter of the model number designate the color. “P” in the 10th position indicates Premium model.
Refer to page 1.7 for paint color code. Detailed paint ordering information is available on the dealer web site at News,
Forms & Links / Pure Polaris / Paint Codes & Part Numbers.
HAMMER™ MODEL YEAR 2005
Model Number Model Description / Color
V05HB126/226 (Feature & Option) Hammer Toxic Green w/ Tribal Tattoo
V05HB26 CA, CAP, DA, DAP, LA, LAP, UA Hammer Cruiser / PHAT Black
V05HB26 CK, DK, LK Hammer Flame Yellow
V05HB26 CL, DL, LL Hammer Indy Red
V05HB26 CM, DM, LM Hammer Cosmic Sunburst
V05HB26 CSP, DSP, LSP, US Hammer Indy Red w/ Tribal Tattoo
HAMMER™ MODEL YEAR 2006
Model Number Model Description / Color
V06HB26 CA, CAP, DA, DAP, LA, LAP, UA Hammer Cruiser / PHAT Black
V06HB26 CB, DB, LB, Hammer Indy Red
V06HB26 CJ, DJ, LJ, Hammer Supersonic Blue w/ Clear Pearl
V06HB26 CK, DK, , LK, UK Hammer Flame Yellow w/ Tribal Tattoo
V06HB26 CLP, DLP, LLP, UL Hammer Nuclear Sunset w/ Tribal Tattoo
VEGAS JACKPOT™ / NESS SIGNATURE SERIES VEGAS JACKPOT™ MODEL YEAR 2006
Model Number Model Description / Color
V06XB26 CA, CAP, DA, DAP, LA, LAP Vegas Jackpot Cruiser / PHAT Black
V06XB26 CM, CMP, DM, DMP, LM, LMP Vegas Jackpot Cruiser Black w/ X Graphics
V06XB26 CN, CNP, DN, DNP, LN, LNP, UN Vegas Jackpot Sunset Red w/ X Graphics
V06XB26 CP, CPP, DP, DPP, LP, LPP Vegas Jackpot Competition Yellow w X Graphics
V06BC26 CR, DR, LR Ness Signature Cruiser Black w/ Ness Flames
V06BC26 CS, DS, LS Ness Signature Supersonic Blue w/ Ness Graphics
V06XB26 CT, CTP, DT, DTP, LT, LTP Vegas Jackpot Sunset Red

GENERAL INFORMATION
1
1.7
PAINT COLOR CODES
PAINT COLOR - 2005 and 2006 PAINT CODE NOTES
Cruiser Black (PHAT) P-266
Indy Red P-293 Aerosols and Touch-Ups require base coat of Indy Red with
topcoat of Clear Metallic (CM). Paint kits require white
undercoater (WU).
Flame Yellow P-388
Turbo Silver P-445 Paint kits require base coat with a topcoat of Clear Metallic (CM)
Cosmic Sunburst P-446 Clear coat (C) required
Toxic Green Pearl P-491 Aerosols, Kits, and Touch-Ups require a white base (WU). Toxic
Green Pearl.
Nuclear Sunset P-493
Competition Yellow P-517
Sunset Red P-520
Nuclear Sunset w/ Tribal Tattoo P-1210 P-493 w/ X Graphic
Flame Yellow w/ Tribal Tattoo P-1214 P-388 w/ Tribal Tattoo
Sunset Red w/ X Graphics P-1223 P-520 w/ X Graphic
Black w/ X Graphics P-1224 P-266 w/ X Graphic
Competition Yellow w/ X
Graphics P-1227 P-517 w/ X Graphic
Supersonic Blue / Clear Pearl P-1231 Aerosols, Kits, and Touch-Ups require a white base (WU).
Supersonic Blue (P-499) and Clear Pearl topcoat (CP).
Metallic Flake Additive METALLIC Add vial of flake to quart of clear base
Silver Undercoater SU Base coat only
Antares Red Undercoater RU Base coat only
Clear C
Clear Metallic CM Clear with metal flake added
Clear Pearl CP Clear with pearl flake added
UNDERCOATERS
(Base Coat Only) WU, OWU, PWU, VVU WU=White Undercoater; OWU=Off-White Undercoater; PWU=Pearl White Undercoater; VVU=Victory Violet
Undercoater

GENERAL INFORMATION
1.8
VEHICLE INFORMATION
VEHICLE IDENTIFICATION NUMBER (VIN)
See “VIN NUMBER LOCATION” on page 1.9 for location on the vehicle.
MODEL NUMBER
See “MODEL NUMBER LOCATION” on page 1.9 for location on vehicle. See “PAINT COLORS BY MODEL” on page 1.6
for color.
*5VPHB26D062000000*
SAE-assigned
World Manufacturing
Identifier
Type:
B = Base Model
C = Custom
D = Deluxe
Series:
C = Canada
D = Domestic (49 State)
L = California
U = United Kingdom
Serial Number
Engine Size:
1 = 1507 cc
2 = 1634 cc
Engine HP:
6 = 78-94 Check Digit
(May be a number
or a letter)
Model Year:
5 = 2005, 6 = 2006 etc. Plant/ Line
Code
Chassis:
A = 8-Ball
C = Kingpin
D = Ness Kingpin (05)
E = Ness Vegas (05)
G = Vegas
H = Hammer
N = Ness Vegas (04)
T = Touring Cruiser
X = Jackpot
B = Ness Jackpot
V05XB26DAP
Chassis:
A = 8-Ball
C = Kingpin
D = Ness Kingpin (05)
E = Ness Vegas (05)
G = Vegas
Engine Size:
1 = 1507 cc
2 = 1634 cc
Engine HP:
6 = 78-94 Series:
C = Canada
D = Domestic (49 State)
L = California
U = United Kingdom
P = Premium Model
Type:
B = Standard
Victory
Model Year:
05=2005; 06=2006, etc.
Color Indicator
H = Hammer
N = Ness Vegas (04)
T = Touring Cruiser
C = Custom
D = Deluxe
X = Jackpot
B = Ness Jackpot
(Billet Wheels, HID Headlight,
Other options as specified)

GENERAL INFORMATION
1
1.9
VIN NUMBER LOCATION
The vehicle identification number (A) is stamped on the right side of the
steering head.
MODEL NUMBER LOCATION
The model label (B) is located on the left side of the steering head.
ENGINE NUMBER LOCATION
The engine number label (C) is attached to the horizontal crankcase
surface (2005 Hammer) or stamped into the right crankcase boss (D)
(2006 models). The label or stamping identifies the engine model and
serial number.
KEY IDENTIFICATION NUMBER
The key identification number (E) is stamped on the key tag. If the key
and the identification number are lost or misplaced, the lock set (ignition
switch / fuel cap) must be replaced.
Key blanks are available from service parts. Locksmiths familiar with the
motorcycle industry will be able to cut a replacement key with the key
I.D. number and a Victory key blank.
A
B
D
C
E