Victory Mounts XUT-3760 User manual

INSTALLATION GUIDE: XUT-3760
Victory Tilt Screen Wall Mounting System
The Victory Tilt Screen Wall Mounting System is designed for secure installation of flat screen
displays up to 60”.
Warning Statements
WARNING
:
THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST A
MAXIMUM WEIGHT OF 175 LBS. IF NOT, THE WALL MUST BE REINFORCED.
PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE
TECHNICIAN, AS OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST
BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS
PERSONAL INJURY, OR EVEN DEATH.
WARNING
:
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE
INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND
TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL
INJURY.
WARNING
:
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION
INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE
INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL
INJURY AND PROPERTY DAMAGE. KEEP THESE INSTALLATION
INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE
REFERENCE.
A secure structure must support the weight, or load, of the display. When mounting
to a wall that contains wooden studs, dead center of the wooden stud must be
confirmed prior to installation.
Do not install on a structure that is prone to vibration, movement or chance of
impact. Failure to do so could result in damage to the display and/or damage to the
mounting surface.
Do not install near heater, fireplace, direct sunlight, air conditioning or any other
source of direct heat energy. Failure to do so may result in damage to the display
and could increase the risk of fire.
At least two qualified people should perform the installation procedure. Injury and/or
damage can result from dropping or mishandling the display.
Recommended mounting surfaces: wooden studs and solid-flat concrete. If the
mount is to be installed on any surface other than wooden studs, use suitable
hardware (which is commercially available).
Contact Victory Mounts with any technical / installation questions.
Included Hardware
Griplates
(Qty 8)
3” Lag Bolts
(Qty 6)
Bubble Level and Bubble
Level Receptacle (Qty 1) Machine Screws (Qty 2)
Flat Washers (Qty 6) NOTE: To correctly determine your hardware,
please refer to the hardware list below.
1/4" Nylon spacers
5/16" Flat washers
(metal)
9/16" Nylon spacers
(large)
1/2" Nylon spacers
(large) Nylon sleeves
(Qty 6)
(Qty 12)
(Qty 6)
(Qty 6)
(Qty 4)
1/4" Nylon spacers
(small)
(Qty 6)
M4 x 25
M5 x 20
M5 x 50
M8 x 20
M4 x 16 (Qty 8)
(Qty 8)
M5 x 12
M5 x 16 (Qty 6)
M5 x 25 (Qty 4)
M6x12 (Qty8)
M8 x 25 (Qty 6)
M8 x 30 (Qty 6)
M8x35 (Qty 4)
M6 x 20 (Qty 6)
M8 x 70 (Qty 4)
M6 x 30
(Qty6)
(Qty 4)
(Qty6)
(Qty 4)
(Qty 6)
Tool List
Phillips Head Screw Driver
Electronic Stud Finder
½” Socket and Wrench
Portable Drill
Minimum 5/16” Masonry Bit for Concrete Installation
¼” Drill Bit for Wood Installations
NOTE: The included level may be permanently
attached to the wall plate. Insert the level
into the bubble level receptacle and attach
it to the wall plate by placing the bubble
level receptacle on the front of the wall
plate and inserting the two (2) machine
screws from the backside. Do not over-
tighten these screws.
Wood Stud Mounting
1. For secure wood stud mounting, the wall plate
must be mounted to two studs at least 16” apart.
2. Use a high-quality electronic stud finder
(commercially available) to locate two adjacent
studs and mark their locations with a pencil.
3. With the help of an assistant, and using the bubble
guide to ensure the wall plate is level, position the
wall plate against the wall in the desired
mounting location.
4. Mark the right, upper and lower and the left (upper
and lower), positions of the small horizontal slots
that are in alignment with the studs.
5. You should mark four positions total.
6. Next, pre-drill a ¼” hole in the wall stud at each
marked location.
Continued on next page
Bubble LevelLag Bolt and Washer
Bubble Level
Receptacle
Bubble Level
Machine
Screws

Continued from previous page
7. With the help of an assistant, position the wall plate against the wall and
line up the mounting slots with drilled holes.
8. For each location, insert a lag bolt and washer into the wall.
9. Tighten each bolt with an open ended socket wrench by turning clockwise until tight.
CAUTION: Do not over-tighten bolts – doing so may cause unnecessary damage to the wall.
Avoid excessive torque.
CAUTION: Do not release the wall plate until it is properly mounted and secured to the wall.
Concrete Mounting
NOTE: The concrete anchors must be used for concrete installation.
They can be purchased at your local hardware store.
1. Begin by placing the wall plate into position against the wall, using the bubble guide to
keep it level.
2. Mark off four holes to be used for securing the mount and place the wall plate aside.
3. Next, drill holes using an electric drill and 5/16” masonry bit.
4. Insert a concrete anchor into each hole.
5. If necessary, a hammer can be used to lightly tap each anchor into place so
that they are flush with the wall.
6. Once all of the anchors are in place, move the wall plate back into position.
7. Attach the nut onto the threaded shaft that is protruding from the wall.
8. Do not tighten until all nuts are in place.
How to Determine Thread Depth
Display Bracket Installation
1. To ensure optimal installation, this kit includes
various screws of different diameters and lengths.
2. Place your TV screen down on a soft, flat surface,
and locate the threaded mounting points that are
located on the back of the display.
3. Determine which screw is the correct length by
carefully inserting a straw, or toothpick, and
mark how deep the mounting point is.
4. If your display has a curved back or a recessed
thread mounting point, a spacer must be used.
NOTE: Select the spacer that is closest in depth to
the recess to keep your bracket as close to
the display as possible.
5. Place the spacer between the mounting bracket and
the display.
6. If a smaller screw is being used (M4, M5, or M6)
please use a square griplate with each screw for
added stability.
Final Installation
1. Attach each bracket to the display by aligning the
holes on each bracket, with the threaded inserts on
the back panel of your display, inserting the screws
through both and turning clockwise until they are fully
inserted.
2. Tighten with a Phillips head screw driver.
CAUTION: Two people are required for this step.
3. To complete the installation of your new plasma
mount, carefully place the television brackets
over the upper and lower mounting crossbars.
Operation and Adjustment
1. Your new mount can be adjusted to fit your individual
needs.
2. You can adjust the tilt of your television by using
the tension knob located on the right-hand side and
left-hand side of the wall plate.
3. Next, turn the tension knob counter-clockwise to
loosen the mounting crossbars.
4. To tilt the mount up, pull on the lower crossbar, while
at the same time pushing on the upper crossbar to
tilt the mount up.
5. To tilt the mount down, pull on the upper crossbar,
while at the same time pushing on the lower
crossbar to tilt the mount down.
6. Once the desired level of tilt is achieved, re-
tighten the mount by turning the tension knob
clockwise.
7. Other features of your display mount include a
cable manager and lock designed to prevent
your television from being removed from the
cross-bar.
8. The cable manager attaches to the cross-bar and
can be used for neatly routing your television’s
power cable.
9. To use the security lock, locate the small metal
tabs located on the arm brackets that attach to
the television and line up the holes.
10. Place a padlock (commercially available) through
the holes and engage to secure the locking tabs in
place.
Progressive Marketing Products, Inc.
3130 E. Miraloma Ave.
Anaheim, CA 92806
800-368-9700
[email protected]
Marking
Marking
Marking the depth Straw or Toothpick
Thread insert
Inverted flat panel display
Adjustment Knob
Cable Manager
Metal Tabs and
Pad Lock (not
included)