Videofied BR250 Assembly instructions

INSTALLATION SHEET
BR250/651/752 Badge Reader
www.videofied.com
Doc. - Ref. 218-BR
Version : November 2016
The BR badge reader is designed to be used within a
Videofied™ alarm system.
Its main features are :
• Interactive wireless technology.
• Dual tamper function.
• Transmits check-in/status signals every 8 minutes
• Lithium batteries : 4 years lifespan.
• Mobility-Use outdoors or indoors with a fully
weatherproof casing withstanding temperatures
from -25°C to +70°C (-13°/158°F ).
Product presentation
Installation guidelines
RF testing will ensure good communication between the
control panel and all system devices. Install the badge reader
and other system devices in the order of the following steps :
>Program the badge reader and all other devices into the
control panel and test RF communication from each intended
device location to the control panel.
>Mount the badge reader at the final location.
Installation and Programming
The following provides summarized steps for device programming
and testing.
1 Mount the base to the wall observing the “TOP” marking.
2Insert 3.6V DC LS14500 Lithium batteries observing correct
polarity.
3With the programming keypad, browse to the ADD A NEW
DEVICE menu (Level 4).
4Press OK/YES. The keypad displays PRESS PROGRAM BUTTON
OF DEVICE.
5 Press program button. The button blinks in green. Wait for
keypad to display BADGE READER nRECORDED.
6 Press OK/YES. The display shows RADIO RANGE TEST?
7 Press OK/YES again to run the test. The keypad display shows
TEST IN PROGRESS.
8 Please make sure the top LED blinks in red, indicating good
communication with the control panel. The test result must stabilize at
8/9 as a minimum.
If the radio range level is below 8/9, change the location of the
detector to obtain satisfactory radio range level.
9Press OK/YES to end the radio range test then ESC NO.
10 Choose a zone for that badge reader (by default that zone will be
delayed ) and name it.
11 The keypad displays OPERATION COMPLETED ? Mount the
badge reader on its base and press OK/YES.
12 Name the detector. When finished, keep ESC NO pressed to exit
from configuration mode.
For full programming details, please refer to the control panel
installation manual.
INIT
Button
Battery
Case

INSTALLATION SHEET
2
BR250/651/752 Badge Reader
www.videofied.com
During arming
The arming stops.
The two indicators flash
green for 5s then turn off: A
fault was detected.
In order to know more
about what happened a
keypad is required.
Without action from the
user, arming will start
again aer 3 min and the
concerned detector will be
bypassed from this arming.
Flashing of the top red
indicator (only) every
second during arming
delay.
The top red indicator
flashes every two
seconds indicating that
the system is armed.
Everything is fine :
System is arming
Problem was
identified during
the incomplete
arming (detection
in and instant area)
The LEDs will stay
on for 5 seconds
The two indicators turn off, the system is
disarmed.
There was no alarm
An alarm
triggered on
The top indicator
flashes green for
2s, and that of the
bottom flashes
fixed green light
and the reader
beeps 4 times
The two indicators
remain on with
fixed green light
for 5 seconds
When reading the badge, the reader emits a beep, then two
beeps indicating the badge has been accepted. The LED
indicators of the reader are going to indicate a message:
When reading the badge, the reader emits a beep, then two
beeps indicating the badge has been accepted. The LED
indicators of the reader are going to indicate a message:
Functioning of indicators
During disarming
Verify with a keypad
in order to know more
about what happened

INSTALLATION SHEET
3
BR250/651/752 Badge Reader
www.videofied.com
Notes de sécurité / (EN) Security notes / (DE) Hinweise zur Sicherheit
Français
• Retirez les piles avant toute opération de
maintenance !
• Attention ! Il y a un risque d'explosion si
l'une des piles utilisées est remplacée par
une pile de type incorrect !
• Respectez la polarité lors de la mise en
place des piles !
• Ne jetez pas les piles usagées !
Ramenez-les à votre installateur ou à un
point de collecte spécialisé.
English
• Remove battery before any
maintenance !
• WARNING, there is a risk of explosion if a
battery is replaced by an incorrect type!
• Observe polarity when setting up the
batteries!
• Do not throw away used batteries!
Dispose of them properly according to
Lithium Metal requirements
Deutsch
• Batterien vor jeglichen Wartungsarbeiten
entfernen!
• Vorsicht, es besteht Explosionsgefahr,
wenn eine Batterie durch eine Batterie
falschen Typs ersetzt wird!
• Achten Sie beim Einsetzen der Batterien
auf die Polung!
• Entsorgen Sie Batterien nicht im
normalen Haushaltsmüll! Bringen Sie
Ihre verbrauchten Batterien zu den
öffentlichen Sammelstellen.
FCC Regulatory Information for USA and CANADA
FCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI Video Technologies may void the FCC
authorization to operate this equipment.
FCC Part 15.105 Class B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed toprovide reasonable protection against harmful interference in aresidential installation. This equipment generates,uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
> Reorient or relocate the receiving antenna.
> Increase the separation between the equipment and receiver.
> Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
> Consult the dealer or an experienced radio/TV technician for help.
Radio frequency radiation exposure information according 2.1091 / 2.1093 / OET bulletin 65
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
and operated with minimum distance of 20 cm between the radiator and your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé.
Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
1 This device may not cause harmful interference, and
2 This device must accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
1 L’appareil ne doit pas produire de brouillage,et
2 L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre
le fonctionnement.

www.videofied.com
North American Headquarters
1375 Willow Lake Blvd, Suite 103
Vadnais Heights, MN 55110
USA
E-Mail : usasales@rsivideotech.com
EMEA SALES
23, avenue du Général Leclerc
92340 BOURG-LA-REINE
FRANCE
4
INSTALLATION SHEET
BR250/651/752 Badge Reader
Electrical Data
Power requirements Three 3.6 V batteries
Battery type Lithium, LS14500
Battery life Up to 4 years
Standby current consumption 24µA
Low battery limit 2.75 V
RF Technology S2View®
Radio Type Spread Spectrum Bidirectional
Operating frequency
868MHz - BR250 (Europe, South Africa, Asia)
915MHz - FHSS - BR651 (USA, Canada, South America)
920MHz - FHSS - BR752 (Australia, South America)
Transmission security AES encryption algorithm
Supervision Polled signal every 8 minutes
Antenna Integrated
Tamper detection Wall and Cover tamper
Display lighting Automatic/ 2 LED
Built in sounder Emits arm and disarm beeps
Operating temperature -25°/+70°C (-13°/+158°F)
Maximum relative humidity 95%, non-condensing
Physical Data
Protection rating IP44 / IK08
Material Polycarbonate UL94
Dimensions 140 mm x 90 mm x 38 mm
(LxWxD): 5 1/2 in. x 3 1/2 in. x 1 1/2 in.
Weight 136 g/4.8oz. (without batteries)
Installation/Mounting
Unit/Base 2 screws secure the Badge Reader to the base
3 screws secure base to flat mounting surface
The BR references are BR651 for USA/Canada/Latam, BR752 for
Australia/South America and BR250 for Europe and the rest of the world.
Standards & Certifications
868MHz (BR250)
Standards :
EN60950-1 : 2006 +A11+A1+AC+A12
EN300220-1 V2.4.1
EN300220-2 V2.4.1
NF EN50130-5: 2011 Class IV
NF EN50131-3: 2009 - Grade 2
NF EN50131-5-3: 2005+/A1:2008 - Grade 2
NF EN50131-6: 2008 Grade 2 –Type C
Certifications :
Europe CE / EN50131 Grade 2
Netherlands NCP
Singapour IDA
SOuth Africa ICASA
915MHz (BR651)
USA FCC Part 15C (FCC47 CFR part15)
Canada IC (RSS-210 Issue 8)
920MHz (BR752)
Australia C-Tick
This manual suits for next models
2
Table of contents
Other Videofied Card Reader manuals