Viking Lrr-4 User manual

PRODUCT MANUAL

Designed, Manufactured and Supported in the USA

COMMUNICATION & SECURITY SOLUTIONS

LRR-4 /LRT-4

Long Range 4 Channel

Receivers / Transmitters

September 18, 2018

VIKING

Features Applications

Specifications

Long Range 433 MHz Four Channel Transmitters

and Receivers with up to 400 ft* Range

Viking’s model LRR-4 Long Range 4 Channel Receivers with

integrated receive antenna and LRT-4 Long Range Wireless 4

Channel Radio Transmitters comprise Vikings high frequency, long-

range (RFID) identification solution. Intended for security access

control applications, the LRT-4’s wireless communication is based

upon a secure, digital, anti-playback routine. The LRT-4

Transmitters have four buttons, each corresponding to its own

Wiegand output on the LRR-4 Receiver. Each Transmitter includes

an integrated red LED, used to indicate both positive button press

and battery strength. They are also equipped standard with a

125 KHz HID** compatible potted proximity module allowing the

Transmitter to also be used as a close range access credential.

The transmitters and receivers operate at 433 MHz allowing a

transmission range of up to 400 ft (line of sight). The LRR-4 receiver

has an adjustable read range, optional external antenna connector,

terminal block with 4 channel Wiegand data output and a transducer

and LED to confirm transmitter button press. The LRR-4 has a

conformal coated circuit board mounted in a NEMA 4, 4x rated box

for use in outdoor applications.

ATTENTION: When ordering LRT-4 Transmitters, quantity,

Facility Code, starting Transmitter, and Proximity Module

Number must be specified. Please use the attached order

form on page 4.

LRR-4 LRT-4

SOLD

SEPARATELY

LRT-4 Long Range Transmitter

• Read range of up to 400 ft (line of sight)

• Convenient key fob design

• 4 buttons to activate up to 4 different Wiegand devices

• Secure, Rolling Code + Encryption, digital, anti-playback wireless

transmission

• Integrated 125 KHz proximity module for close range access credential

(can be used with Viking Proximity card readers and certain 125 KHz HID** readers)

• Replaceable CR2032 battery lasts up to 500,000 button presses

• Robust buttons rated for up to 1 million activations

• LED to indicate button press and battery strength

• Internal diaphragm / gasket seals circuit board from moisture and debris

• CE mark

LRR-4 Long Range Receiver

• Read range of up to 400 ft (line of sight)

• Secure, digital, anti-playback wireless communications

• 4 channels of 26 bit Wiegand data output

• Optional external antenna connector

• LED and transducer transmitter feedback

• Adjustable read range

• Removable terminal block for easy wiring

• Cable grommet included for sealing cable exit

• CE mark

*Up to 400ft line of sight range

** HID and the HID logo are registered trademarks of HID Global Corporation, an ASSA

ABLOY company. All other trademarks are the property of their respective owners.

Use with the following Viking models to remotely activate

relays for door/gate control, etc:

www.vikingelectronics.com

Information: (715) 386-8861

Model Description DOD

AES-2000 Accessible Entry System (with ES-3 controller) 202

AES-2005 Accessible Video Entry System (with ES-3 controller) 204

C-4000 Apartment / Office Entry Controller 164

ES-1 Stand Alone Keyless Entry System 193

ES-3 Entry System Controller (requires power adapter) 195

K-1200-IP VoIP 12 Button Apartment Entry Phone 271

K-1205-IP VoIP Apartment Entry Phone with Camera 272

K-1270-IP VoIP Entry Phone with Card Reader 273

K-1275-IP VoIP Entry Phone with Camera and Card Reader 274

K-1700-IP VoIP Entry Phone with Keypad 253

K-1705-IP VoIP Entry Phone with Keypad and Camera 254

K-1770-IP VoIP Entry Phone with Keypad and Card Reader 257

K-1775-IP VoIP Entry Phone with Keypad, Camera, and Card Reader 258

K-1770-3 Entry Phone with Keypad and Card Reader 275

K-1775-3 Entry Phone with Keypad, Camera, and Card Reader 280

K-1900-8-IP VoIP Entry Phone with Handset and Keypad 361

Shipping Weight: LRR-4 = 0.81 lb

LRT-4 = 0.1 lb

(see page 2 for complete specifications)

LLR-4 Specifications LRT-4 Specifications

Optional External

Antenna Connector

Audio Beeper

Model LRR-4

10-PIN Terminal Block

Read Range

Adjustment

Antenna Switch

Beeper Switch

Dimensions: 6.3” x 2.5” x 2.4”

AD0

AD1

BD0

BD1

CD0

CD1

DD0

DD1

GND

+VDC

Internal View

Cable Requirements

24 AWG minimum, multi-conductor stranded with an overall foil shield, for example

Belden 9540 or similar. Per the SIA’s Wiegand specification, maximum cable length

is 400 feet (121.92 m).

Grounding

Shield (drain) continuity must run from the Receiver to the access panel. Shield

and reader ground must be tied together at the access panel and connect then to

an earth ground at one point.

Power

Power required is 12 VDC nominal at 120mA. The Receiver may be powered by

the access panel. A linear power supply is recommended for best operation. Power

Supply is not included, but can be powered directly from Viking model ES-1,

K-1700-IP, C-4000, AES-2000, and AES-2005 entry systems. When used with an

ES-3 a separate 12 VDC power supply is required.

Mounting

The Receiver may be mounted indoors or outdoors. The base of the enclosure

includes a drill template providing mounting provisions to a wall box (standard

North American and European), as well as pre-drilled holes in the four corners

allowing mounting to a flat surface.

Read Range Adjustment

As shipped, the Receiver is set for the maximum read range, which is nominally

up to 400 feet. This may be reduced by adjusting the range pot in the counter-

clockwise direction. Additionally, for optimal read range it is important that the

Receiver be mounted as far from potential interference sources as possible. These

sources may include, but are not limited to, large metal obstructions, as well as

magnetic fields and radio transmissions. Note for each installation, read range may

vary.

External LED Indicator (Beeper Switch must be set to ON in order for

the external LED to operate)

Amber: Normal powered on state

Flash Green: An activated Transmitter button press has been received and

processed

Flash Red: A non-activated Transmitter button press has been detected

Off: Receiver is not powered on, or failed to power up successfully (or

Beeper Switch is turned to OFF)

Antenna Switch

As shipped, the Receiver’s Antenna Switch is set in the INT position. If a separate

antenna is to be used, then the switch should be set in the EXT position.

Beeper Switch

As shipped, the Receiver’s Beeper Switch is set in the ON position. If the

installation technician prefers to disable the beeper and External LED Indicator,

then the Beeper Switch should be set in the OFF position.

10-Pin Terminal Block - Refer to the information below for cabling to the

Receiver:

AD0: Button One, Wiegand Data 0, Channel A (GREEN)

AD1: Button One, Wiegand Data 1, Channel A (WHITE)

BD0: Button Two, Wiegand Data 0, Channel B (GREEN)

BD1: Button Two, Wiegand Data 1, Channel B (WHITE)

CD0: Button Three, Wiegand Data 0, Channel C (GREEN)

CD1: Button Three, Wiegand Data 1, Channel C (WHITE)

DD0: Button Four, Wiegand Data 0, Channel D (GREEN)

DD1: Button Four, Wiegand Data 1, Channel D (WHITE)

GND: Power, 0VDC (Ground)

+VDC: Power, 12VDC Nominal

Output Format

Transmitters are sequentially coded in the industry standard 26bit Wiegand format,

with exact number sequences. The Transmitter has an external number printed on

the ID label found on the back of the Transmitter. Specific coding details, including

internal number, facility code, and ID range can be found on the LRT-4 order form

on page 4.

Enrollment

Transmitter must be clicked twice within a Receiver’s read range to be learned

upon initial Receiver power up. This synchronizes the transmitter and receiver

rolling codes. If the transmitter is clicked more than five times outside of the

Receivers read range the transmitter and receiver will be desynchronized. To re-

sync, click twice again within read range.

Time-Out

LRT-4 transmitters make use of a time-out feature to preserve battery life and

prevent interference with other transmitters in the field. When a button is held down

continuously the transmitter will transmit the code once and shutdown and will

power up once the button is released.

Battery Replacement

Transmitters include a replaceable CR2032, 3.3V, lithium battery. The battery

should be replaced when a button press does not result in a flash of the LED,

reliable read range, and/or an output from the Receiver. To replace the battery,

follow the directions below:

1. Using a coin, place it in the gap (2-piece unit) near the key ring holder

and twist to pop the transmitter open.

2. Remove the old battery.

3. Insert the new CR2032, 3.3V, lithium battery. Be sure the plus (+) side of

the battery is visible when installed.

4. Snap both pieces together.

Range

Up to 400ft line of sight.

Buttons

(1 to 4)

Key Ring

Holder

Red LED

ID Label

Model LRT-4

Dimensions: 2.5” x 1.4” x 0.52”

Front View Back View

VIKING

ATTENTION: When ordering LRT-4 Transmitters, quantity,

Facility Code, starting Transmitter, and Proximity Module

Number must be specified. Please use the attached order

form on page 4.

For more information see Viking C-4000, Apartment / Office Entry Controller, Product Manual DOD 164.

Gate

Touch Tone

Programming

Phone (not included)

RAD-1A Remote Access

Device (not included,

see DOD 410)

Remote Touch

Tone Programming

Phone (not included)

VIKING©

VIKING

ELECTRONICS

HUDSON, WI 54016

STAND ALONE

DOOR CONTROLLER

ENTRY SYSTEM

POWER 12V DC

MODEL ES-1

POWER

PROGRAM

PHONE

LOG

BUS

2345

GANG

PROG

6789

WIEGAND

DEVICE

10 11

DOOR

STRIKE

N.O.

COM

N.C.

BLK

RED

GRN

WHT

Viking ES-1 (not included, DOD 193) or

Viking ES-3* (not included, DOD 195)

120V AC

12V DC Adapter

(included with ES-1)

Optional Viking PRX-3

(not included, DOD 221)

Model

LRR-4

120V AC

12V DC Adapter

(included with PRX-3)

* Important: When using the LRR-4 with

an ES-3, the LRR-4 must be powered

separately by a 12 VDC power adapter

(Viking model PS-2A).

+VDC is connected to “+” on PWR

adapter. GND is connected to “-” on PWR

adapter and to “BLK” terminal on ES-3.

Using a LRR-4 with an ES-1 or ES-3 for Wireless Gate Control

Using a LRR-4 with a C-4000 to Wirelessly Control up to 4 Gates

Troubleshooting

Should any of the corrective actions mentioned above not improve performance, please contact Viking directly.

Note 1. This lithium battery is widely available, and commonly used in electronic devices, including cameras and remote controls.

Note 2. Dispose of the battery according to local requirements. Recycle when possible.

Note 3. For best performance the Transmitter should be used as far from interference sources as possible. These sources may include, but are not limited to, large metal

obstructions, such as duct work and appliances, as well as magnetic fields and radio emissions.

Issue / Possible Causes Correction Action

No data received / Transmitter not enrolled Transmitter must be clicked twice to be learned by the Receiver upon initial Receiver power up

Short Read Range / Receiver Knob Adjustable knob should be set to the maximum setting

Prox insert not working / Compatibility Support with HID® 125-kHz Proximity Protocol readers only

IF YOU HAVE A PROBLEM WITH A VIKING PRODUCT, CONTACT: VIKING TECHNICAL SUPPORT AT (715) 386-8666

Our Product Support Department is available for assistance Monday - Friday 8am - 5pm central time. So we can give you better service, before you call please:

1. Know the model number, the serial number and what software version you have (see serial label).

2. Have your Technical Practice in front of you.

3. It is best if you are on site.

Warranty

RETURNING PRODUCT FOR EXCHANGE

The following procedure is for equipment that has failed out-of-box (within 10 days of purchase):

1. Customer must contact Viking’s Technical Support at 715-386-8666 to determine possible causes for the problem.

The customer MUST be able to step through recommended tests for diagnosis.

2. If the Technical Support Product Specialist determines that the equipment is defective based on the customer's input

and troubleshooting, a Return Authorization (R.A.) number will be issued. This number is valid for fourteen (14)

calendar days from the date of issue.

3. After obtaining the R.A. number, return the approved equipment to your distributor, referencing the R.A. number. Your

distributor will then replace the Viking product using the same R.A. number.

4. The distributor will NOT exchange this product without first obtaining the R.A. number from you. If you haven't

followed the steps listed in 1, 2 and 3, be aware that you will have to pay a restocking charge.

RETURNING PRODUCT FOR REPAIR

The following procedure is for equipment that needs repair:

1. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization (RA)

number. The customer MUST have a complete description of the problem, with all pertinent information regarding the

defect, such as options set, conditions, symptoms, methods to duplicate problem, frequency of failure, etc.

2. Packing: Return equipment in original box or in proper packing so that damage will not occur while in transit. Static

sensitive equipment such as a circuit board should be in an anti-static bag, sandwiched between foam and individually

boxed. All equipment should be wrapped to avoid packing material lodging in or sticking to the equipment. Include

ALL parts of the equipment. C.O.D. or freight collect shipments cannot be accepted. Ship cartons prepaid to:

Viking Electronics, 1531 Industrial Street, Hudson, WI 54016

3. Return shipping address: Be sure to include your return shipping address in the box. We cannot ship to a PO Box.

4. RA number on carton: In large printing, write the R.A. number on the outside of each carton being returned.

TWO YEAR LIMITED WARRANTY

Viking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for a period of two years from the date of purchase from any authorized Viking distributor. If at any time during the warranty period,

the product is deemed defective or malfunctions, return the product to Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI., 54016. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization

(R.A.) number.

This warranty does not cover any damage to the product due to lightning, over voltage, under voltage, accident, misuse, abuse, negligence or any damage caused by use of the product by the purchaser or others. This warranty does not cover non-

EWP products that have been exposed to wet or corrosive environments. This warranty does not cover stainless steel surfaces that have not been properly maintained.

NO OTHER WARRANTIES. VIKING MAKES NO WARRANTIES RELATING TO ITS PRODUCTS OTHER THAN AS DESCRIBED ABOVE AND DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTIES OR MERCHANTABILITY OR FITNESS FOR

ANY PARTICULAR PURPOSE.

EXCLUSION OF CONSEQUENTIAL DAMAGES. VIKING SHALL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE TO PURCHASER, OR ANY OTHER PARTY, FOR CONSEQUENTIAL, INCIDENTAL, SPECIAL OR EXEMPLARY DAMAGES

ARISING OUT OF OR RELATED TO THE SALE OR USE OF THE PRODUCT SOLD HEREUNDER.

EXCLUSIVE REMEDY AND LIMITATION OF LIABILITY. WHETHER IN AN ACTION BASED ON CONTRACT, TORT (INCLUDING NEGLIGENCE OR STRICT LIABILITY) OR ANY OTHER LEGAL THEORY, ANY LIABILITY OF VIKING SHALL BE

LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, OR AT VIKING'S OPTION, REFUND OF THE PURCHASE PRICE AS THE EXCLUSIVE REMEDY AND ANY LIABILITY OF VIKING SHALL BE SO LIMITED.

IT IS EXPRESSLY UNDERSTOOD AND AGREED THAT EACH AND EVERY PROVISION OF THIS AGREEMENT WHICH PROVIDES FOR DISCLAIMER OF WARRANTIES, EXCLUSION OF CONSEQUENTIAL DAMAGES, AND EXCLUSIVE

REMEDY AND LIMITATION OF LIABILITY, ARE SEVERABLE FROM ANY OTHER PROVISION AND EACH PROVISION IS A SEPARABLE AND INDEPENDENT ELEMENT OF RISK ALLOCATION AND IS INTENDED TO BE ENFORCED AS SUCH.

A basic gate access controlled entry point is wired

as shown right. The relay can be connected as

either Normally Open, or Normally Closed. All 26

bit Wiegand devices are fully supported.

Power and Data from the ES-1 (Data only

from ES-3) can be installed up to 500 feet

away using 24 gauge wire. Viking Wiegand

devices can run even further. The ES-1 or

ES-3 can support either a LRR-4 Receiver or

Proximity Card Reader (Viking model PRX-1

or PRX-3), or both. If any two Wiegand

devices are used, one can be placed on each

side of a doorway/gate for bi-directional

(entry and exit) access control.

Printed in the U.S.A

Order Form for Viking Model LRT-4 Long Range Transmitters

Please fill out the following form and return it to your Viking

distributor or email it to [email protected]

IMPORTANT: PROGRAMMED TRANSMITTERS ARE

NON-CANCELABLE AND NON-RETURNABLE

CUSTOMER INFORMATION:

Date: Distributor PO#:

Contact:

Company:

Address:

City / State / Zip:

Phone: Fax:

LRT-4 TRANSMITTER AND PROXIMITY MODULE PROGRAMMING:

Quantity:

Facility code (2-254):

First Internal (programmed) transmitter and proximity module

First External Transmitter number:

or No External Transmitter Number, check box:

Signature:

Fill out entire form;

scan and email to:

[email protected]

or fax to: 715-386-4344

(Internal Use Only)

File Name:

Notes:

Quick Definitions:

Facility code: A 3-digit number

that each transmitter and proximity

module contains in order to provide

greater security. Usually the

transmitter used at a given building

all have the same facility code.

Internal Transmitter and Proximity

module number: A 5-digit number that

each transmitter contains. This

number must be programmed in

the transmitter by Viking Electronics

External Transmitter Number: The

number that is printed on a label and

placed on the back side of each

transmitter.

number (00001-65534):

Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries

assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.

DOD 226 ZF303900 REV A

This manual suits for next models